Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 29, Problem 85RQ
Why do samples analyzed in an electron microscopes generally have to be coated with a thin metal film?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
d)Please explain how to distinguish the types of defects that can be detected using X-Rays and AMI.
You can use 1kV-30kV in a scanning electron microscope (SEM). You are asked to analyze the surface topography as well as bulk microstructure of a cast iron. Keep working distance and spot size constant for your experiment. CALCULATE the ‘electron interaction’ volume or depth of penetration of electron beams to the sample for the 2kV voltage (applied). Which voltage (2kV, 5kV, 10kV, 20kV, or 30kV) do you prefer for surface topography and which one for bulk microstructure? For calculation, consider the cast iron as just iron. Show your work.
A typical energy of electrons in a modern transition electron microscope is 300 keV. Calculate the corresponding wavelength of the electron beam assuming that the vacuum inside the microscope is ideal.
Chapter 29 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 29 - Over the latter half of the 20th century, what...Ch. 29 - What was the major motivation for developing...Ch. 29 - Prob. 3RQCh. 29 - What is an example of a device feature that is...Ch. 29 - What type of manufacturing technology dominates...Ch. 29 - Name the four categories of miniature systems...Ch. 29 - Give two differences between lab-on-a-chip and...Ch. 29 - What is a scaling law?Ch. 29 - As the primary dimensions of an object decrease,...Ch. 29 - In the design of a water heater, the mean time...
Ch. 29 - Prob. 11RQCh. 29 - Name two conventional manufacturing processes that...Ch. 29 - Prob. 13RQCh. 29 - Why does breadth of scale of a product have an...Ch. 29 - What is the most complicated, expensive, and...Ch. 29 - Name three purposes that a resist mask can play.Ch. 29 - Name four key lithography methods.Ch. 29 - Name two through-mask lithography techniques.Ch. 29 - Name two direct-write lithography techniques.Ch. 29 - List the sequence of steps involved in...Ch. 29 - Of the two major classifications of photoresists,...Ch. 29 - List four requirements of a photoresist.Ch. 29 - What limits the resolution of a photoresist?Ch. 29 - What is meant by resist sensitivity?Ch. 29 - What is one requirement that contributes to the...Ch. 29 - List the three types of exposure methods used in...Ch. 29 - Why is projection printing equipment called a...Ch. 29 - What are typical materials etched during...Ch. 29 - What is etch bias?Ch. 29 - Prob. 30RQCh. 29 - What are some possible defects that can result...Ch. 29 - What are some possible defects that can result...Ch. 29 - List and describe two properties of etchants.Ch. 29 - What is etch anisotropy dependent upon?Ch. 29 - What is the difference between wet and dry?...Ch. 29 - What is dry etching?Ch. 29 - What are the three main categories of dry etching...Ch. 29 - What is the difference between plasma etching and...Ch. 29 - What is deep reactive ion etching?Ch. 29 - What is a benefit of using UV lasers to machine...Ch. 29 - Which type of non-lithographic micromachining...Ch. 29 - What are thin films?Ch. 29 - A) What is the difference between solution...Ch. 29 - What are the two broad categories of vapor...Ch. 29 - List two different types of physical vapor...Ch. 29 - List two advantages of sputtering over...Ch. 29 - What is meant by step coverage with regards to...Ch. 29 - Why is step coverage important?Ch. 29 - Prob. 49RQCh. 29 - What does gettering mean in relation to wafer...Ch. 29 - How are undesirable gas-phase reactions controlled...Ch. 29 - What is the key difference in the reactor designs...Ch. 29 - What are the two types of LPCVD reactor designs?...Ch. 29 - In metallization, what is the difference between a...Ch. 29 - What is the advantage of using plasma-enhanced on...Ch. 29 - A) What is epitaxy? B) is it important for...Ch. 29 - Name four techniques for solution deposition onto...Ch. 29 - Name four roll-to-roll processing techniques for...Ch. 29 - What is a semiconductor?Ch. 29 - Name three common semiconductor materials.Ch. 29 - Give three reasons why silicon is the most popular...Ch. 29 - Prob. 62RQCh. 29 - What is a silicon boule?Ch. 29 - Prob. 64RQCh. 29 - What are some geometric concerns involved with...Ch. 29 - What is meant by the term doping?Ch. 29 - What is the difference between n�type and...Ch. 29 - Name three methods for doping a silicon wafer.Ch. 29 - Prob. 69RQCh. 29 - Prob. 70RQCh. 29 - Prob. 71RQCh. 29 - Why are rapid thermal processing technologies...Ch. 29 - What are two ways in which silicon dioxide is...Ch. 29 - Give two reasons why wet oxidation is better...Ch. 29 - What is a p�n junction? \What can it be used...Ch. 29 - Prob. 76RQCh. 29 - Assuming an n�doped substrate is clean, list the...Ch. 29 - What is planarization and why is it needed?Ch. 29 - What is meant by the term ULSI?Ch. 29 - In general, what technological breakthroughs were...Ch. 29 - What drives the increase in component density and...Ch. 29 - Why are clean rooms so important to...Ch. 29 - What is the advantage of electron microscopy over...Ch. 29 - What is the collective advantage of...Ch. 29 - Why do samples analyzed in an electron microscopes...Ch. 29 - What are two differences between a scanning...Ch. 29 - What is important about a dual�beam focused ion...Ch. 29 - Why is white light normally preferred for...Ch. 29 - What is one advantage of an atomic force...Ch. 29 - What is the breadth of scale of an automotive...Ch. 29 - What is the breadth of scale of a computer...Ch. 29 - Which has a larger breadth of scale, the...Ch. 29 - Prob. 4PCh. 29 - A piece of silicon has an integrated resistor...Ch. 29 - Based on what you learned in problem #5, which...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 4. Poly-Si of the following structure is to be etched using a completely anisotropic dry-etch process, to remove poly-Si at a rate of 0.1 mm /min. However, this etching process has poor selectivities: selectivity to SiO₂ is 5; selectivity to photoresist is 2. (a) Sketch the cross-section after 5 minutes of etching. (b) Calculate the angle of the SiO₂ sidewalls after 5 minutes of etching. 0.lum oxide 1 um 0.7um Poly-Si I photoresist 0.5 umarrow_forwardMacroscopic examination is distinguished from microscopic examination by: The low magnification employed The small areas examined in relation to the whole specimen The high magnification employed The large areas examined in relation to the whole specimenarrow_forwardRj gandhiarrow_forward
- Q18arrow_forwardMagnetic resonance imaging (MRI) is a medical imaging technique that located in hospitals and radiology centers. MRI uses a strong magnetic field and radio waves to create detailed images of the organs and tissues within the body. (i) MRI system operators must make sure not to carry any metallic objects when they enter the room that house the MRI, even when the machine is not operating. Give the reason. (ii) What happens if a magnet was hitted with a hammer repeatedly? Explain your answer. Robots are used in automobile industries to weld two components at specific locations. Thus, the end position of the robot arms must be determined accurately in order to weld the components at the precise position. In selecting a proper material for the robot arms design, identify the factors must be considered for this application.arrow_forward2. What is the principle of RAMAN spectroscopy. Why is RAMAN spectroscopy considered a complement to IR spectroscopy, give examples of materials where it is used very commonly.arrow_forward
- A thin film of oil, on the surface of glass , results in destructive interference. If the wavelength of the incident light (650 nm) , find the thickness of the film. (Nair =1; Nott = 1.45; Nglass = 1.52)arrow_forwardWhat kind of material would you expect to show an x-ray diffraction profile like the one shown below? 130K 120K 110K 100K- 90K- 80K- 70K- 60K- 50K- 40K- 30K- 20K 10K Intensity (counts) 20⁰ O a. A material containing iron O b. A crystalline solid O c. O d. A single crystal solid A liquid A mixed amorphous and crystalline solid O e. O f. An amorphous solid A grain boundary is an example of a A vacancy is an example of a An interstitial is an example of a A dislocation is a perfect crystal 1-dimensional (line) defect 3-dimensional (volume) defect 0-dimensional (point) defect 2-dimensional (plane) defect Angle (degrees 20arrow_forwardI want questions and answers aboutGauge experiment for a concave diffraction grating (Roland Installation)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Introduction to Diffusion in Solids; Author: Engineering and Design Solutions;https://www.youtube.com/watch?v=K_1QmKJvNjc;License: Standard youtube license