Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 29, Problem 31SDP
To determine
Figure I.7b in the General Introduction shows a mirror that is suspended on a torsional beam, and can be inclined through electrostatic attraction by applying a voltage on either side of the micromirror at the bottom of the trench. Make a flowchart of the manufacturing operations required to produce this device.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A prototype of a tube with a square cross-section is to be fabricated using stereolithography. The outside dimension of the square = 100 mm and the inside dimension = 90 mm (wall thickness = 5 mm except at corners). The height of the tube (z-direction) = 80 mm. Layer thickness = 0.1 mm. The diameter of the laser beam (“spot size”) = 0.25 mm, and the beam is moved across the surface of the photopolymer at a velocity of 500 mm/s.
Compute an estimate for the time required to build the part, if 10 s are lost each layer to lower the height of the platform that holds the part. Neglect the time for post-curing.
solve the question given in image completely.
What is the shape factor F12 for the situation shown in Fig. 1 below ?
Chapter 29 Solutions
Manufacturing Engineering & Technology
Ch. 29 - Define MEMS, SIMPLE, SCREAM, and HEXSIL.Ch. 29 - Give three examples of common...Ch. 29 - Why is silicon often used with MEMS devices?Ch. 29 - Describe bulk and surface micromachining.Ch. 29 - What is the purpose of a spacer layer in...Ch. 29 - What is the main limitation to successful...Ch. 29 - What are common applications for MEMS andMEMS...Ch. 29 - Prob. 8RQCh. 29 - Prob. 9RQCh. 29 - Explain the differences between stereolithography...
Ch. 29 - What is MolTun? What are its main advantages?Ch. 29 - What is HEXSIL?Ch. 29 - What do SIMPLE and SCREAM stand for?Ch. 29 - Describe the difference between isotropic etching...Ch. 29 - Lithography produces projected shapes, so true...Ch. 29 - Which process or processes in this chapter allow...Ch. 29 - What is the difference between chemically reactive...Ch. 29 - The MEMS devices discussed in this chapter are...Ch. 29 - Explain how you would produce a spur gear if...Ch. 29 - Prob. 20QLPCh. 29 - Prob. 21QLPCh. 29 - Prob. 22QLPCh. 29 - Is there an advantage to using the MolTun process...Ch. 29 - The atomic-force microscope probe shown inFig....Ch. 29 - Estimate the natural frequency of the cantilever...Ch. 29 - Using data from Chapter 28, derive the time needed...Ch. 29 - It is desired to produce a 500 m by 500...Ch. 29 - If the Reynolds number for water flow through a...Ch. 29 - Prob. 30SDPCh. 29 - Prob. 31SDPCh. 29 - Prob. 32SDPCh. 29 - Design a micromachine or device that allows the...Ch. 29 - Conduct a literature search and determine the...Ch. 29 - Perform a literature search and write a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- I am confused about how this expressions was simplified. Can someone walk through this step-by-step?arrow_forwardTwo students decided to print a prototype for a gear. Student A use layer thickness of .1 mm and an infill density of 25%. Student B use a layer thickness of 0.07 mm and an infill density of 45%. Which student will take less time to print the gear? Select one: Stu nt since the ckness of layer is smaller and the infill density is higher. O We can't decide which process takes less time O Student A since the thickness of the layer is larger and the infill density is lower. Student B because thickness is higher than B and the infill density has no effect on the process speed. Student A because thickness is higher than B and the infill density has no effect on the process speed.arrow_forwardExplain microscopic and macroscopic approaches.arrow_forward
- Explain this step by steparrow_forwardRefer to the picture below.arrow_forwardA hemispherical dome of radius 40 feet is to be given 5 coats of paint, each of which is 1/100 inch thick. Use linear approximation to estimate the volume of paint needed for the job.( Hint: Approximate the change in the volume of a hemisphere when the radius increases from 40 feet to 40 feet 5/100 inches. Don't forget to make sure this increased radius is in terms of feet. )It will take approximately cubic feet of paint to apply all 5 coats of paint.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Unit Conversion the Easy Way (Dimensional Analysis); Author: ketzbook;https://www.youtube.com/watch?v=HRe1mire4Gc;License: Standard YouTube License, CC-BY