Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 27, Problem 7SA
What does a slope in the spark line represent?
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
朱媽
2020-09-23 19:17 reply:2 Read:11
What kind of situation might happened to the
engine due to too high temperture?
What does a slope in the spark line represent?
a. Low secondary resistance
b. High resistance in the primary circuit
c. An incorrect air-fuel mixture
d. High resistance in both the primary and secondary circuit
If the spark line is totally flat, is longer than 2 ms, and is less than 500 volts, there is a good chance that __________ .
Chapter 27 Solutions
Automotive Technology
Ch. 27 - Prob. 1SACh. 27 - Name the three types of trace pattern display...Ch. 27 - Prob. 3SACh. 27 - List at least two methods of checking the...Ch. 27 - Prob. 5SACh. 27 - What is the typical procedure for checking the...Ch. 27 - What does a slope in the spark line represent?Ch. 27 - What happens if one of the ground electrodes of a...Ch. 27 - True or False? The first test when checking a...Ch. 27 - True or False? Coil secondary resistance is...
Ch. 27 - True or False? On some engines, if the gap between...Ch. 27 - Richer air-fuel mixtures. a. decrease the...Ch. 27 - While checking a pickup coil with an ohmmeter, a...Ch. 27 - A CKP sensor can be checked with all of the...Ch. 27 - Which of the following will cause one or more, but...Ch. 27 - Prob. 1ASRQCh. 27 - Prob. 2ASRQCh. 27 - Prob. 3ASRQCh. 27 - Technician A says that EMI can affect sensor...Ch. 27 - While discussing waste spark EI systems:...Ch. 27 - While discussing how to test a Hall-effect...Ch. 27 - While discussing the possible causes for a...Ch. 27 - Prob. 8ASRQCh. 27 - While discussing EI service and diagnosis:...Ch. 27 - While discussing engine misfire diagnosis:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What is meant by regulator creep?arrow_forward20. Technician A says that an ignition system must generate sufficient voltage to force a spark across the spark plug gap. Technician B says that the ignition system must time the arrival of the spark to coincide with the movement of the engine's pistons and vary it according to the operating conditions of the engine. Who is correct? O a. Technician A O b. Technician B c. Both A and B O d. Neither A nor Barrow_forwardWhich of the following will cause one or more, but not all, firing lines to be higher than normal? a. High resistance in the spark plug wire b. Faulty fuel injector c. Defective spark plug d. All of the abovearrow_forward
- An engine starts and runs briefly after a small quantity of fuel is put into the spark plug hole, but it doesn't not start when fuel is added to the carburetor throat. Tech a says that the problem may be that the exhaust valve is not closing completely due to carbon buildup. Tech b says it may be due to a defective carburetor mounting gasket. Who is correct?arrow_forwardDetermine the following: a. Type of engine b. Number of strokes c. Manner of ignitionarrow_forwardWhat is the function of On/Off valve?arrow_forward
- what is upward velocity of box Earrow_forward! What are engine parameters affecting ignite timing?arrow_forwardIt represents the net power output of the engine at the crankshaft. * Your answer If the fuelair ratio is proper and ignition timing is correct, the combustion process should be completed just after center at the beginning of the power stroke. * our answer The ignition time varies from 20 to 35 degrees before the top dead center to ensure complete combustion when the piston is slightly past the top quiet center position. TRUE OR FALSE? * Your answerarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Solids: Lesson 53 - Slope and Deflection of Beams Intro; Author: Jeff Hanson;https://www.youtube.com/watch?v=I7lTq68JRmY;License: Standard YouTube License, CC-BY