Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 27, Problem 7RQ
What are the capabilities of wire EDM? Could this process be used to make tapered parts? Explain.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
(a)
An engineer would like to drill a square hole of 20 mm x 20 mm with depth of
25 mm on a layered structure of natural fibre-reinforced polymer composite. He
encountered delamination problem in the workpiece (Figure 3) when he used
conventional cutting tool to drill the hole. Instead of using conventional
machining process, discuss ONE suitable advanced machining process that can
be applied for this machining purpose and predict TWO possible limitations for
the selected process.
Cutting
Tool
Delamination
Composite Material
Figure 3. Delamination of the composite material.
What is Bragg Grating.
• Explain its working principle.
• One practical application that uses the same technique
What is the difference between caulking and fullering? Explain with the help of neat sketches.
Chapter 27 Solutions
Manufacturing Engineering & Technology
Ch. 27 - Describe the similarities and differences between...Ch. 27 - Name the processes involved in chemical machining....Ch. 27 - Explain the difference between chemical machining...Ch. 27 - What is the underlying principle of...Ch. 27 - Explain how the EDM process is capable of...Ch. 27 - What are the important features of the Blue Arc...Ch. 27 - What are the capabilities of wire EDM? Could this...Ch. 27 - Explain why laser Microjet has a large depth of...Ch. 27 - Describe the advantages of water-jet machining.Ch. 27 - What is the difference between photochemical...
Ch. 27 - What type of workpiece is not suitable for...Ch. 27 - What is an undercut? Why must it be considered in...Ch. 27 - Explain the principle of hybrid machining.Ch. 27 - Give technical and economic reasons that the...Ch. 27 - Why is the preshaping or premachining of parts...Ch. 27 - Explain why the mechanical properties of workpiece...Ch. 27 - Prob. 17QLPCh. 27 - Prob. 18QLPCh. 27 - Why has electrical-discharge machining become so...Ch. 27 - Prob. 20QLPCh. 27 - Which of the advanced machining processes would...Ch. 27 - Which of the processes described in require a...Ch. 27 - Describe your thoughts regarding the laser-beam...Ch. 27 - Are deburring operations still necessary for some...Ch. 27 - List and explain factors that contribute to a poor...Ch. 27 - What is the purpose of the abrasives in...Ch. 27 - Which of the processes described in this chapter...Ch. 27 - Is kerf width important in wire EDM? Explain.Ch. 27 - Comment on your observations regarding Fig. 27.4.Ch. 27 - Why may different advanced machining processes...Ch. 27 - A 200-mm-deep hole that is 30 mm in diameter is...Ch. 27 - If the operation in Problem 27.31 were performed...Ch. 27 - A cutting-off operation is being performed with a...Ch. 27 - A 0.80-in.-thick copper plate is being machined by...Ch. 27 - Explain why it is difficult to produce sharp...Ch. 27 - Make a list of the processes described in this...Ch. 27 - Would the processes described in this chapter be...Ch. 27 - Prob. 38SDPCh. 27 - Describe your thoughts as to whether the...Ch. 27 - Make a list of machining processes that may be...Ch. 27 - At what stage is the abrasive in abrasive...Ch. 27 - Describe the similarities and differences among...Ch. 27 - Describe the similarities and differences among...Ch. 27 - Describe any workpiece size limitations in...Ch. 27 - Suggest several design applications for the types...Ch. 27 - Based on the topics covered in Parts III and IV,...Ch. 27 - Review Example 27.1 and explain the relevant...Ch. 27 - Precision engineering is a term that is used to...Ch. 27 - With appropriate sketches, describe the principles...Ch. 27 - Make a table of the process capabilities of the...Ch. 27 - One of the general concerns regarding advanced...Ch. 27 - It can be seen that several of the processes...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Define specific energy for plane strain machining (cutting). In plane-strain machỉning, the two main sources of energy dissipation are deformation along the shear plane (~70%) and friction at the tool-chip contact along the rake face (~30%). Consider machining of a rigid perfectly-plastic work material whose uniaxial yield stress is 700 MPa, and is independent of strain rate and temperature. A tool of zero-degree rake angle is employed. Measurements showed the (deformed) chip thickness to be twice that of the undeformed chip thickness. Based on the aforementioned distribution of energy, estimate the specific energy for this process.arrow_forwardA furniture company that makes upholstered chairs and sofas must cut large quantities of fabrics. Many of these fabrics are strong and wear-resistant, which properties make them difficult to cut. What nontraditional process(es) would you recommend to the company for this application? Justify your answer by indicating the characteristics of the process that make it attractive.arrow_forwardExplain (i) Angle of repose with a Neat diagram (ii) Impending Motion and Limiting Frictionarrow_forward
- A 10 mm thick plate is rolled to 7 mm thick in a rolling mill using 1000 mm diameter rigid rolls. The neutral point is located at an angle of 0.3 times the bite angle from the exit. What will be the thickness of the plate at the neutral point.arrow_forwardCalculate the material removal rate and electrode feed rate in the electrochemical machining of an iron surface that is 25 mm × 25 mm in cross-section, using NaCl in water as electrolyte. The gap between the tool and the work-piece is 0.25 mm. The supply voltage is 12 volt D.C. The specific resistance of electrolyte is 3 2 cm. Take for iron: Valency = 2, Atomic weight = 55.85,Density = 7860 kg/m³.arrow_forwarda rod is to be manufactured using turning operations and is made of Nickel alloy. The rod is 80 mm in length and 15 mm in diameter. The final required diameter is 10 mm and the spindle rotates at N = 500 rpm while the tool axial speed is 100 mm/ min. Calculate material removal rate, cutting speed, cutting time, the power dissipated, and cutting force.arrow_forward
- What is the Mannesmann milling process? Why is the Mannesmann piercing process not capable of producing extremely long lengths of seamless tubing?arrow_forwardExplain the differences between deforming processes and material removal processes.arrow_forwardExplain the benefits of wireline coring?arrow_forward
- In plane-strain orthogonal machining, the two main sources of energy dissipation are deformation along the shear plane (~70%) and friction at the tool-chip contact along the rake face (~30%). Consider plane-strain machining of a rigid perfectly-plastic work material whose uniaxial yield stress is 700 MPa, and is independent of strain rate and temperature. A tool of zero-degree rake angle is employed. Measurements showed the (deformed) chip thickness to be twice that of the undeformed chip thickness. Based on the aforementioned distribution of energy, estimate the specific energy for this process.arrow_forwardWhat is the manufacturing process of lathe bed? Which material will be suitable for the product? Justify your answer.arrow_forwardA cylindrical workpiece of 100mm diameter and 150mm in height (Fig. 1) is upset (open die forged) at 1200° C to 100mm height disk (Fig. 2). Material of the workpiece is low carbon steel. A graphite lubricant reduces the friction to u=0.25. A press with 2-m/sec speeds is used to make this part. At 1200° C the material has the values for its C=48MPA and m=0.08 parameters Fig. 1 Height=150mm, Diameter=100mm Fig. 2 Height = 100mm, Diamete = ? mm (a) (b) (c) Determine the final diameter of the disk (see Fig. 2) Determine the true strain rate at the end of process. Calculate the flow stress at the end of the stroke.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Types of Manufacturing Process | Manufacturing Processes; Author: Magic Marks;https://www.youtube.com/watch?v=koULXptaBTs;License: Standard Youtube License