Technician A says that EMI can affect sensor signals. Technician B says that EMI can cause intermittent driveability problems. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor B

Q: What does the engine load sensor mean? What are the electrical lines of this sensor, explain it?

A: Engine load can be measure by a sensor which is commonly known as Mass Air Flow Sensor. It measure…

Q: The oil level sensor use the ... technic for * operation.

A: Oil level sensors: A oil level sensor works on the principle of buoyancy.

Q: While discussing EGR systems with a differentialpressure feedback electronic (DPFE) sensor:…

A: Exhaust Gas Recirculation (EGR) is a cost-effective and efficient method for lowering nitrogen…

Q: A TPMS sensor is being replaced. Technician A says that if you replace it with a manufacturer…

A: Objective: To determine which statement is correct for replacing the TPMS sensor.

Q: This landing instrument guides an aircraft to maintain a 2.5 to 3 degrees angle when attempting to…

A: Given question: The landing instrument that guides an aircraft to maintain a 2.5 to 3 degree angle…

Q: Explain how

A: Sensor

Q: Which of the following will be used by a contact type sensor ? a. Ultrasonic Sound Wave b. Dial…

A:

Q: Light intensity of a halogen bulb is to be tested using a sensor. Identify from the below options,…

A: Answer is Photo transistor

Q: 103) Which of the following sensors is NOT an input necessary for electronic control of the…

A:

Q: °Mice that monitor movement using an optical sensor rather of a traditional mechanical one.

A: Optical sensors have emerged as a viable alternative to traditional mechanical sensors in computer…

Q: Integral controller has large overshoot. Select one: O True O False

A: Demerits System gets to be sluggish due to the expansion of fundamentally term. Takes bigger time…

Q: A STOL command line in galaxy is us- ommands to the spacecraft and to e procedures. O True O False

A: Given Data : STOL Command line  Blind commanding line

Q: Explain the working of NDIR and chemical sensors of exhaust gas analyzers

A: NDIR (Nondispersive Infrared Sensors) It is a simple spectroscopic sensor that is used as the gas…

Q: iii) Discuss the controller's behavior in terms of transient, steady state response. What about the…

A: The consistent state reaction is continuously consonant, and has the same recurrence as that of…

Q: What is a TPS sensor?

A: The full form of TPS is throttle position sensor.

Q: The IAT sensor location is

A: IAT sensor: It is Intake Air Temperature sensor which is use to check the temperature of the intake…

Q: What is attitude indicator

A: The attitude indicator (AI), formerly known as the gyro horizon or artificial horizon, is a flight…

Q: What is a camera light meter,  and how is it important to determine proper exposure? is used to…

A: camera light meter is used for the measurement of the light reflection during the process and then…

Q: The relation between the output and input of the sensor is ___________

A: Correct option is:

Q: The relation between the output and input of the sensor is O a. square of the input O b. Linear O c.…

A: The relation between the output and input of the sensor is linear.

Q: is an example of analog indicating type device. a. Ultra Violet Recorders O b. Voltmeter O c.…

A:

Q: OBD II systems use several modes of operation. List three of them.

A: There are nine Global OBDII modes. Three of them are Monitor Status and Current Data, Freeze Frame,…

Q: Technician A says that the oxygen sensor provides the major input during the open-loop…

A: There are two modes of operations for the engine: (1) Open loop mode: In this mode, no feedback is…

Q: the activity of an O2 sensor is best monitered with a ______ . a. scan tool b. logic probe c.…

A: the activity of an O2 sensor is best monitered with a ______ .

Q: Which of the following is true of a critically damped piezo-electric accelerometer? A. = 2.0 B. Wn =…

A: Explained the condition for the critically damped piezoelectric accelerometer.

Q: Question: What is the main difference between active Sensor and passive Sensor: ( Select the…

A: A sensor transducer is a device which converts a physical form of signal into measurable form of…

Q: Describe atleast two methods of checking the operation of hall effect sensors?

A: Hall effect sensor : Hall effect sensor is characterized as the straight transducer which is use to…

Q: timing diagram with IPO, IPC, TPO, TPC,EPO, EPC as 35,35,40,40,35,50

A: The port timing diagram for required functions with angle is shown below.

Q: Question: What is the best example of passive sensor from the following

A: Given: Question: What is the correctclassification of the modern encodersensor ( Select the best…

Q: Identify the sensor which uses float for its operation.

A: Identify the sensor which uses float for its operation. Answer: Rotameter

Q: The eluate exiting the column first passes through a suppressor before reaching the detector. Why is…

A: To explain: The need of suppressor.

Q: 104) Which of the following inputs is NOT a driver commanded input? Brake pedal switch Mass airflow…

A: Given Driver commanded input To find Verify from the following which is not driver commanded input

Q: LVDT can be used as the primary  sensing element . Select one: True False

A: LVDT stands for Linear Variable Differential Transformer. It is a device that measures linear…

Q: Which of the following is not a voltage-generating type sensor? vehicle speed sensor OSS MAP ISS

A: Voltage generating type sensors This type of generators consists of different types of speed sensors…

Q: Contact Type displacement sensors makes direct contact with the object being monitored. Select one:…

A: True Contact type displacement sensors makes direct contact with the object  being monitored

Q: 8. Which of the following statements about the sensors of quadrotor UAVS is WRONG? a.Barometer…

A: The barometer is a device that is used to measure the atmospheric pressure at a location.  The…

Radiation

Radiation can be described as the energy in the form of a particular matter or electromagnetic waves traveling in the air and can be in the form of light, sound, and heat. Radiation can be detected through special instruments like X-rays. The radiation from a cooler object is less intense as compared to the radiation from hot objects.