While discussing secondary voltage: Technician A says that the normal required secondary voltage is higher at idle speed than at wide open throttle conditions. Technician B says that the maximum available secondary voltage must always exceed the normally required secondary voltage. Who is correct?

While discussing secondary voltage: Technician A says that the normal required secondary voltage is higher at idle speed than at wide open throttle conditions. Technician B says that the maximum available secondary voltage must always exceed the normally required secondary voltage. Who is correct?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter22: Condensers

Section: Chapter Questions

Problem 16RQ: Explain the basic operation of a combination ORI and ORD low-ambient head pressure control valve.

See similar textbooks

Related questions

Q: The wind speed beyond which the turbine should stop its operation is triggering speed cut-in speed…

A: Cut out speed, wind speed beyond cut out speed, the turbine should stops its operation. Every wind…

Q: A throttle position sensor has _________ . a- a 0-5 volts signal output terminal b- a 5-volt…

A: all answers are correct hence c option is correct. Explanation → →A throttle position sensor signals…

Q: What are the different between TEV and TEV with equalizer?

A: Thermostatic expansion valve (TEV) is used to control the flow of refrigerant through the evaporator…

Q: advantages of using electronic controls rather than relying on conventional hydraulic controls in a…

A: In modern vehicles mostly electronic controls are used rather than the conventional hydraulic…

Q: Draw and Explain the Circuit diagram for holding the cylinder of double acting cylinder in the fully…

A: Solution: C = Double acting cylinder P = Pump E = Electric Motor T = Tank F = Filter R = Relief…

Q: Describe the voltage needed by an accelerator between accelerating tubes.

A: In this problem, it is asking about the voltage that is needed by an accelerator between…

Q: Which one of the following is a not electrical method of actuation,but it uses air to actuate…

A: Solution:

Q: What three functions are performed by the clutch safety switch when the car has an electronic engine…

Q: Which of the following is commonly used as a transmissionneutral start switch?a. Mercuryb.…

A: Given Transmission neutral start switch To find Technology used

Q: Technician A says that a stator aids in directing the flow of fluid from the impeller to the…

A: Technician A wrong Only Technician B correct

Q: What is the maximum torque? to avoid damage from throttle r LAB T

Q: one way flow control valve is the type of valve which is used to control the speed of an actuator.…

Q: Technician A says that some shift solenoids can be activated by providing a ground for the solenoid.…

A: The shift solenoid is used in the gear assembly which shifts the gear according to the desire of…

Q: Lockout may involve: Opening a disconnect swite b. Closing a valve. a. Placing a hlock in the equir

A: lockout switches in an electrical circuit are that are removable.

Q: Technician A says that double-cone synchronizers have friction material on both sides of the…

A: Technician A says that double-cone synchronizers have friction material on both sides of the…

Q: Explain the three controls of hazards.

A: To Explain: The 3 controls of Hazards. Explanation: Hazards: Anything that cause harm such that…

Q: What affect shift valves to cause a downshift?

A: Downshifting is the process of lowering the gear of the transmission system of an automobile. There…

Q: True or false? A damped, forced system can undergo pure resonance.

A: The given statement is FALSE

Q: the speed can be positive or negative false true

A: Speed is a scalar quantity. it has no direction so, speed can be positive or zero. it cannot be…

Q: controls on/off of the motor, when the air compressor tank reaches the specified bar.

A: Compressed and filtered air enters the tank after coming out of the Air compressor

Q: 1. How is the cylinder 3A (towards the right) fundamentally different than cylinders 1A and 2A? 2.…

A: To find : 1- how is the cylinder 3A (towords the right )fundamentally different than cylinder 1A and…

Q: Briefly explain the function of the 'Thermostatic Valve' and 'Expansion Tank' in a water cooled…

A: Thermostatic valve It is the kind of check valve fitted in the outlet of the engine which opens and…

Q: Technician A says that throttle position is an important input in most electronic shift control…

A: In electronically controlled automatic transmission, the most appropriate gear ratio for the power…

Q: Design an ignition system used for modern cars.

Q: 1) What is the effect if it occurs error data reading on Throttle Position Sensors?

A: As per policy, only one question can be answered. Hence first question is answered. (1) What is…

Q: What is the primary difference between an automatic traction control system and a stability control…

A: Traction control system in an automobile is designed to prevent the driving wheel from loosing the…

Q: Instruction: Complete the following table of Pneumatic Symbols. Name Symbol Name Symbol Compressor…

A: The complete table of Pneumatic symbols are shown in the following attached image:

Q: what is an attenuator used for in vehicle

A: A attenuator is used in the vehicles. It is intended to absorb impact of high or low speed crash,…

Q: neumatic Dia

A: Required Pneumatic diagram and name of its component.

Q: which one of the componets is used in Hydraulic systems only? a)counter balance valve b)Quick…

A: Let us discuss about hydraulic systems.

Q: Explain the above : pressure sensor, pressure gauge and pressure transmitter with an application

A: Pressure is defined as the forces by the liquid and gas on the surface and it is measured in Newton…

Q: 1-Can the (watt )regulator be used for higher speeds? 2-What does regulator stability mean?

A: 1. No, the fan consumes the same amount of current operated at different speeds. As when you control…

Q: governer of Conventional Engine

A: given: Discuss the principle of operation of the frequency governer of Conventional Engine…

Q: What is indicated by a LTFT reading of 24 percent?

A: Given Data : LTFT

Q: Describe the procedure for checking clutch pedal free travel

A: Clutch pedal free travel is a specific distance that a clutch has to travel to reach the point where…

Q: differentiate b/w overdamped, under damped , criticaly damped, undAmped system

A: The decay of oscillations in a system following a disturbance is described by the dimensionless…

Q: neat diagram, explain the wind turbine components such as Rotor, Drivetrain and Control System

A: The kinetic energy of wind waves when converted into electrical energy this mechanical process is…

Q: A counter balance valve is not used for always flow retardation continuously, and resists its flow…

A: true

Q: How can shift feel be controlled?

A: For many years, accumulators and associated circuits have been the dominant way for regulating…

Q: If an actuator fails to move, name five possible causes.f an actuator has slow or erratic motion,…

A: Actuator is a component of a machine which capable in moving in a controlled mechanism.It consist of…

Q: Technician A says that a faulty radiator fan relay can cause an engine to overheat. Technician B…

A: The radiator in an automobile is used to take away the excess heat of the engine and sending it out…

Q: A. Analyze and discuss the Extension Speed of Controlling Cylinder.

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: Which of the following is a control that relates directly to vacuum controlled EGR systems??…

A: PORTED VACCUM SWITCH IS A CONTROL THAT relates directly to vacuum controlled EGR systems as No…

Q: Answer the following question: 1. On an aircraft enumerate the turboprop starting procedures.

Q: system

A: Hydraulic system performance-associated matters can be grouped into inoperative, slow, fast, and…

Q: Explain the Interruption Cycle with neat sketch

A: The Interruption cycle (also known as the fetch–decode–execute cycle) is the cycle that the…

Q: Draw the symbol of compressor with FRL and pressure switch with required specifications and also…

A: Symbol of FLR:

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Expert Solution

Step 1

Solution:

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Technician A says that a faulty radiator fan relay can cause an engine to overheat. Technician B says that bidirectional control is NOT used to test an electric cooling fan. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
(B) Choose the correct answer for the following statements:- 1- For a faster response time, a spool type of directional control valve use a-Over lapping, b-Zero lapping, c- Under lapping, d- Non of them
A hot-wire MAF has low resistance across it when the wire is hot: Technician A says that this condition will cause the engine to stall as soon as you put the transmission into gear. Technician B says that this condition will cause the transmission to shift late. Who is correct?
While discussing ignition timing requirements: Technician A says that more advanced timing is desired when the engine is under a heavy load. Technician B says that more advanced timing is desired when the engine is running at high engine speeds. Who is correct?
Explain why a height-sensing proportioning valve is required on some vehicles.
Which of the following statements is not true? A direct acting PRV: Is complex in construction, therefore can malfunction if a very small dirt gets trapped inside the valve, which may result in safety hazard Offers uneven flow Does not provide precise pressure control Causes more wastage of HP compared to a compound one Which of the following basic system components has the primary function of removing the heat of compression from the air? Receiver Relief valve Pressure regulator Dryer Aftercooler Which of the following statements is true? A single acting cylinder may have two ports at two different ends and pressurized fluid can be directed to both of them A single acting cylinder with two ports will can be used as a double acting cylinder A single acting cylinder may have two ports at two different ends but into only one of the ports pressurized fluid is being directed A single acting cylinder…
one way flow control valve is the type of valve which is used to control the speed of an actuator. Select one: True False
An engine cranks slowly: Technician A says that a possible cause of the problem is poor starter circuit connections. Technician B says that an engine problem could be the cause. Who is correct?
Technician A says throttle pressure is controlled directly by the pressure regulator valve. Technician B says one of the primary purposes of the pressure regulator valve is to fill the torque converter with fluid. Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
. the engine rpm is measured by measuring the current of an alternrator, driven by the engine voltage of a DC generator, driven by the engine frequency of an alternrator, driven by the engine
Which of the following is true about a sequence valve? Sequence valves: A. Allow a check valve to override its normal operation B. Controls the rate of air flow in a pneumatic system C. Direct air flow to a different area in a circuit when actuated by pressure level D. Open and close the intet and outlet ports in a pneumatic system
1. What is the difference between running mate and firing order? 2. Enumerate the engine auxiliary systems and briefly discuss each of their functions?