Technician A says that a stator aids in directing the flow of fluid from the impeller to the turbine. Technician B says that a stator is equipped with a one-way clutch that allows it to remain stationary when necessary. Who is correct?

Q: Which of the following is a symbol of the valve which continuously, resisting its flow even after…

A: Solution:

Q: List any four advantages of the Vertical Axis Wind turbine.

A: Four advantages of vertical axis wind turbine - 1) Omnidirectional Natural of the Rotor Vertical…

Q: Explain the importance of a cone clutch with an application

A:

Q: The diesel engines operates with low pressure than petrol engine a. FALSE b. TRUE

A:

Q: Which of the following components give support to the wind turbine?

A: Explanation All the support provide by foundation to the wind turbine. There are two types of load…

Q: Which torque converter components is attached to the engine flywheel? A-impeller B-stator…

A: Main Parts of the Torque Converter are :- 1. Impeller 2. Stator 3. Turbine 4. Transmission fluid (…

Q: i. Describe the operation when valves 1 and 2 are in the positions as shown. ii. What would happen…

A: The  two way valves is  fill and drain a vessel is given.

Q: How many compression ring and oil ring a IC engine piston will have? a. 2 compression ring and 1…

A: Piston of internal combustion engine have three rings for each cylinder. Top two rings are called…

Q: Explanation of the operation of the sterilizer in the drone

A: Drones today use three and six axis gyro stabilization technology to provide navigational…

Q: out any four non return valves

A:

Q: To supply combustion air, a forced draft fan requires 1975 rpm at 4.8 lb-ft. What horse power rating…

A: The speed, N = 1975 rpm The torque provided, T = 4.8 lb.ft

Q: While discussing the cause of an oil leak in an axle housing, Technician A says if the fluid leaks…

A: Technician B is correct. As the leakage in an axle housing is due to the damaged axle seals. So. the…

Q: draw a Single acting cylinder circuit for Hydraulic system using 3/2 single solenoid valve operated…

A:

Q: In a double acting reciprocating pump, the piston carries suction and expulsion at the not same…

A: Yes, it is true.

Q: Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the…

A: A drum brake is a brake that uses friction caused by a set of shoes or pads that press outward…

Q: 4. How fast must a gear pump be run to produce a flowrate of 4.0 GPM if the displacement is 0.4 in³?

A: Given displacement =0.4in3 and flowrate 4.0GPMWe know that Where:231 is a conversion factor to…

Q: Carbon deposits on the intake valve or seat may cause the valve not to close properly. Tech a says…

A: If carbon deposits form on the valves or valve seats, the valves will be unable to close properly.…

Q: Explain with the aid of schematic diagram the working operation of two pressure valve and shuttle…

A: Twin pressure valve: Draw the schematic diagram of the twin pressure valve.

Q: Which one of the following devices creates only pressure? which one the correct ? 1 -Pneumatic…

A: It is required to determine which of the given device creates only pressure.

Q: Four functions of a clutch

A: Clutch is defined as the machine element which is used to engage and disengage the driver and driven…

Q: .Explain how to use the device to start the engine (0 to idle speed) with the vehicle not moving

A:

Q: Explain how the sterilizer in the drone works

A: Drones today use three and six axis gyro stabilization technology to provide navigational…

Q: List five advantages the use of piezoelectric injectorshas over solenoid-based injectors.

A: Given Injectors To find Advantages of piezoelectric injectors over solenoid-based injectors

Q: An engine starts and runs briefly after a small quantity of fuel is put into the spark plug hole,…

A: An engine starts and runs briefly after a small quantity of fuel is put into the spark plug hole,…

Q: With a neat sketch explain the operation of a stratified charge engine.

A:

Q: Radial hydraulic thrust is the summation of unbalanced impeller forces acting in the axial direction

A: according to the given questions

Q: A pneumatic power system will usually have a return line  a. True b. False

A: Concept: 1) Pneumatic power system consists of some pneumatic valves, Electro-pneumatic valves,…

Q: List three possible causes of a noisy bearing during clutch operation.

A: There are many types of clutch noises such as whistling or whining, rattling noises, and many more.…

Q: What is normal air flow rate? How is air flow pressure measured? 4- Which engine produces the most…

A: (2) Normal air flow rate: Means 1 atmosphere  or 101.3KPa   Base pressure Base Temperature…

Q: Technician A uses a feeler gauge and straightedge to determine the pump cover flatness.Technician B…

A: A feeler gauge is a hand-held instrument that is used to measure the distance between two objects…

Q: A pump forms a ___________system A. isolated B. closed C. both open and isolated D. open

A: A pump forms a open system always because both mass as well as energy transfer take place in pumps.

Q: What is the primary difference between hydraulics and pneumatics?

A:

Q: n a DCV, this part is designed with lands that channel the flow through the valve to specific ports…

A: DCV is the directional control values used in the hydraulic and pneumatic system, It controls the…

Q: How does a servo valve work?

A: Servo Valve :  A servo valve is also considered as directional control valve and They are capable to…

Q: Describe the functions of the hydraulic systemcombination valve.

A: Hydraulic fluids today are used for a variety of things. A hydraulic fluid's primary role is to…

Q: Name the different controls used in centrifugal compressors and explain their functions.

A: given; centrifugal compressor are used for delivering high pressure gas and temperature.

Q: In pneumatic actuators, fluid is used instead of compressed gas as in hydraulic actuators. True or…

A: In pneumatic actuators , compressed gases are used to transfer power . In hydraulic incompressible…

Q: Identify the Pump which increase the pressure due to squeezing action and explain its working…

A: The pumps which is used to increase the pressure by squeezing action is gear pump or rotary pump.…

Q: Which of the following is true about a sequence valve? Sequence valves:

A: A sequence valve is a normally closed, pressure-operated poppet or spool valve that opens at a…

Q: Q14. Which scenario will happen to the double acting cylinder if there are oil leakage at the direct…

A: 14. Which scenario will happen to the double acting cylinder if there are oil leakage at the direct…

Q: What would be done to increase the compressor speedon a belt-driven compressor?A. Decrease drive…

A: Typically, belt pulley systems are used to drive the generators that power the compressors. The size…

Q: A.I) The term pressure drop refers to what in a hydraulic circuit a. The change in the flow rate in…

A:

Q: Why check valve is used in hydraulic system? Describe the working principle of a pilot operated…

A:

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.