Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
6th Edition
ISBN: 9780135257272
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 23, Problem 2CQ
Two technicians are discussing oil pumps. Technician A says that many oil pumps are driven directly off the front of the crankshaft. Technician B says that some are driven from the distributor if the engine uses a distributor-type ignition system. Which technician is correct?
- a. Technician A only
- b. Technician B only
- c. Both Technicians A and B
- d. Neither Technician A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Technician A says that the engine oil drain
plug typically needs to be replaced with a
new one at each oil change. Technician B
says that engine oil drain plugs must be
tightened with a torque wrench when they
are installed. Who is correct?
Select one:
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
Technician A says that you may be able to
smell antifreeze from a leaking heater core.
Technician B says that you may be able to
hear a loose belt when the engine is running.
Who is correct?
Select one:
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Carbon deposits on the intake valve or seat may cause the valve not to close properly. Tech a says that the flywheel will be harder to spin when starting the engine. Tech b says that the engine will loose power. Who is correct?
Chapter 23 Solutions
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Ch. 23 - What causes a wedge-shaped film to form in the...Ch. 23 - What is hydrodynamic lubrication?Ch. 23 - Explain why internal engine leakage affects oil...Ch. 23 - Describe how the oil flows from the oil pump,...Ch. 23 - What is the purpose of a windage tray?Ch. 23 - Normal oil pump pressure in an engine is...Ch. 23 - Two technicians are discussing oil pumps....Ch. 23 - A typical oil pump can pump how many gallons per...Ch. 23 - In typical engine lubrication systems, what...Ch. 23 - Hydrodynamic lubrication created by the wedging...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
A pipe flowing light oil has a manometer attached, as shown in Fig, P1.52. What is the absolute pressure in pip...
Fundamentals Of Thermodynamics
Locate the centroid of the area. Prob. 9-17
Engineering Mechanics: Statics
Define or describe each type of fluid: (a) viscoelastic fluid (b) pseudoplastic fluid (c) dilatant fluid (d) Bi...
Fluid Mechanics: Fundamentals and Applications
Assume the following vectors are already defined: V1=[302]V2=[214]V3=[5131]V4=[0.50.10.20.2] For each of the fo...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
CONCEPT QUESTIONS
15.CQ3 The ball rolls without slipping on the fixed surface as shown. What is the direction ...
Vector Mechanics for Engineers: Statics and Dynamics
Convert the following quantities from English to SI units: a. 98 Btu/(hr-ft-F) b. 0.24 Btu/(lbm-F) C. 0.04 Ibm/...
Heating Ventilating and Air Conditioning: Analysis and Design
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says throttle pressure is controlled directly by the pressure regulator valve. Technician B says one of the primary purposes of the pressure regulator valve is to fill the torque converter with fluid. Who is correct? a. A only b. B only c. Both A and B d. Neither A nor Barrow_forwardAn engine starts and runs briefly after a small quantity of fuel is put into the spark plug hole, but it doesn't not start when fuel is added to the carburetor throat. Tech a says that the problem may be that the exhaust valve is not closing completely due to carbon buildup. Tech b says it may be due to a defective carburetor mounting gasket. Who is correct?arrow_forwardWhile discussing central port injection systems: Technician A says that CPI systems use one injector and several injector nozzles. Technician B says that CPI systems open each injector sequentially. Who is correct? A.Technician A B.Technician B C.Both A and B D.Neither A nor Barrow_forward
- A vehicle has had several radiator replacements, and each time there has been pinhole leaks in the aluminum. Technician A states that the engine coolant may need to be exchanged more often. Technician B states that the engine grounds should be inspected closely since this could be the cause. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forwardTechnician A says that a stator aids in directing the flow of fluid from the impeller to the turbine. Technician B says that a stator is equipped with a one-way clutch that allows it to remain stationary when necessary. Who is correct?arrow_forwardTechnician A says that an air-conditioning system removes heat from inside the engine. Technician B says that the heating system removes heat from the inside of the vehicle. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
- True or False? The camshaft is always locatedin the engine block.arrow_forwardTechnician A says that black exhaust smoke is an indication of a too-rich air-fuel mixture. Technician B says that white smoke (steam) is an indication of coolant being burned in the engine.arrow_forwardThe diesel engines operates with low pressure than petrol engine a. FALSE b. TRUEarrow_forward
- Technician A says that a two-stroke oil injection system uses a gravity-fed pressure system. Technician B says that a reservoir is not needed to store injection oil. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardan engine is being discussed for lean running condition. technician A checks for air leak in the intake. Technician B checks for alcohol in the fuel. who is correct?arrow_forwardCam bearings in OHV engines are typically whichtype?a. Split insertb. Full-roundc. Thrustd. None of the abovearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License