Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
6th Edition
ISBN: 9780135257272
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 20, Problem 7CQ
Two technicians are discussing testing coolant for proper pH. Technician A says that coolant has a pH above 7 when new and becomes lower with use in an engine. Technician B says that OAT and HOAT coolants have a lower pH when new compared to the od green IAT coolant. Which technician is correct?
- a. Technician A only
- b. Technician B only
- c. Both Technicians A and B
- d. Neither Technician A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A vehicle is having its water pump replaced.
When the water pump is removed, severe
corrosion is found on the water pump
impeller, and inside the engine. Technician A
states that the radiator cap may be
overpressurizing the system. Technician B
states that the vehicle may have been run
with 100% water in the cooling system for
some time. Who is correct?
Select one:
a. Technician A only
b. Technician B only
c. Both Technicians A and B
d. Neither Technician A nor B
A technician is inspecting a vehicle and finds
the upper radiator hose is collapsed, and the
cooling system pulled into a vacuum when
cold. Technician A states that a leak in the
surge tank could be the cause. Technician B
states that the radiator cap is most likely
defective. Who is correct?
Select one:
a. Technician A only
b. Technician B only
c. Both Technicians A and B
d. Neither Technician A nor B
Technician A says that coolant hoses should
be squeezed to check for hardening or
softening. Technician B says that coolant
hoses should be visually inspected for
swelling and cracks. Who is correct?
Select one:
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Chapter 20 Solutions
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Ch. 20 - What types of coolant are used in vehicles?Ch. 20 - Why is a 50/50 mixture of antifreeze and water...Ch. 20 - What are the differences among IAT, OAT, HOAT, and...Ch. 20 - What are some of the heavy metals that can be...Ch. 20 - What is the difference between galvanic activity...Ch. 20 - Coolant is water and ____________. a. methanol b....Ch. 20 - As the percentage of antifreeze in the coolant...Ch. 20 - Adding a chemical to make ethylene glycol coolant...Ch. 20 - Asian red coolant is what type? a. IAT b. OAT c....Ch. 20 - PHOAT coolant is what color? a. Dark green b. Red...
Ch. 20 - DEX-COOL is ____________. a. propylene glycol b....Ch. 20 - Two technicians are discussing testing coolant for...Ch. 20 - What percentage of coolant is water? a. 80% b. 50%...Ch. 20 - Reusing old coolant is generally not approved by...Ch. 20 - A voltmeter was used to check the coolant and a...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
What types of polymers are most commonly blow molded?
DeGarmo's Materials and Processes in Manufacturing
Select a mechanical component from Part 3 of this book (roller bearings, springs, etc.), go to the Internet, an...
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
A biological fluid moves at a flow rate of m=0.02kg/s through a coiled, thin-walled, 5-mm-diameter tube submerg...
Fundamentals of Heat and Mass Transfer
Repeat Problem 4-6 except solve by the vector loop method.
DESIGN OF MACHINERY
3.3 It is known that a vertical force of 200 lb is required to remove the nail at C from the board. As the nail...
Vector Mechanics for Engineers: Statics
5.1 through 5.9
Locate the centroid of the plane area shown.
Fig. P5.1
Vector Mechanics for Engineers: Statics and Dynamics
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that you may be able to smell antifreeze from a leaking heater core. Technician B says that you may be able to hear a loose belt when the engine is running. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTwo technicians are discussing a coolant drain and refill. Technician A says that draining the coolant removes all coolant from the system. Technician B says that any trapped air in the system will bleed itself out automatically. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardCoolant hoses are being discussed. Technician A states that many manufacturers recommend coolant hose replacement on a maintenance schedule. Technician B states that coolant hoses can fail prematurely due to contamination by oil. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forward
- A vehicle has had several radiator replacements, and each time there has been pinhole leaks in the aluminum. Technician A states that the engine coolant may need to be exchanged more often. Technician B states that the engine grounds should be inspected closely since this could be the cause. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forwardd. Check oil level & moisture content 19. If the main wire (coil) to the distributor and the coil to the switch are broken, replace them and make sure the connections are clean and tight relevant to a. Breaking system b. Ignition system c. Ventilation system d. Combustion system 20. The required gap in ignition system between---------- a.-4 to 5 b.-0.4 to 5 c.-0.4 to 0.5 d.-4 to 0,5 |21. Which of the following is the fouled of spark plug a. Soot b. Oil c. Over heated d. All of the above |22.The suitable thread of spark plug for heavy engine is a. M19 b. M18 c. M15 d. M16 23. Using a Torque wrench, tighten the plugs to the specified torque. (Most) 4mm plugs are torqued to four kilograms per square inch. a. True b. False 24. Start the engine and evaluate its performance refers to a. Weekly Maintenance b. Annually Maintenance c. Daily Maintenance d. None of them 25. Check to see if Dynamo is working properly. If necessary, adjust the regulator refers to a. Weekly Maintenance b. Annually…arrow_forwardTechnician A says that broken engine mounts can cause the fan to hit the shroud. Technician B says that missing or broken air dams can cause an engine to overheat. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Two techs are discussing oil coolers. Technician A says that when inspecting oil- to-water type coolers, look for mixing of the fluids: oil in the coolant, and coolant in the oil. Technician B says that when inspecting oil-to-air type coolers, look for oil in the coolant only. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardWhen performing a coolant pressure test, Technician A says to pressurize the system to the pressure shown on the radiator cap. Technician B says that the coolant should be drained before performing the test. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that coolant hoses should be squeezed to check for hardening or softening. Technician B says that coolant hoses should be visually inspected for swelling and cracks. Who is correct?arrow_forward
- An overheating vehicle is being discussed. Technician A states that the vehicle may be overheating becuase the heater control valve is stuck closed. Technician B states that the vehicle may be overheating because the PCM in not energizing the cooling fan relay. Who is correct?arrow_forwardTechnician A says that liquid cooling an engine helps to maintain a consistent operating temperature. Technician B says that oil is circulated through the cooling system to remove heat from the engine's parts. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that when installing an oil filter, you should tighten it with a filter wrench to prevent it from falling off. Technician B says that oil filters should only be installed by hand. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Extent of Reaction; Author: LearnChemE;https://www.youtube.com/watch?v=__stMf3OLP4;License: Standard Youtube License