Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
6th Edition
ISBN: 9780135257272
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 20, Problem 1CQ
Coolant is water and ____________.
- a. methanol
- b. glycerin
- c. kerosene
- d. ethylene glycol
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
ANSWER THERMOFLUIDS QUESTIONS
A vehicle is having its water pump replaced.
When the water pump is removed, severe
corrosion is found on the water pump
impeller, and inside the engine. Technician A
states that the radiator cap may be
overpressurizing the system. Technician B
states that the vehicle may have been run
with 100% water in the cooling system for
some time. Who is correct?
Select one:
a. Technician A only
b. Technician B only
c. Both Technicians A and B
d. Neither Technician A nor B
Graphite is __.a. an anaerobic substanceb. an RTVc. an aerobic substanced. none of these
Chapter 20 Solutions
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Ch. 20 - What types of coolant are used in vehicles?Ch. 20 - Why is a 50/50 mixture of antifreeze and water...Ch. 20 - What are the differences among IAT, OAT, HOAT, and...Ch. 20 - What are some of the heavy metals that can be...Ch. 20 - What is the difference between galvanic activity...Ch. 20 - Coolant is water and ____________. a. methanol b....Ch. 20 - As the percentage of antifreeze in the coolant...Ch. 20 - Adding a chemical to make ethylene glycol coolant...Ch. 20 - Asian red coolant is what type? a. IAT b. OAT c....Ch. 20 - PHOAT coolant is what color? a. Dark green b. Red...
Ch. 20 - DEX-COOL is ____________. a. propylene glycol b....Ch. 20 - Two technicians are discussing testing coolant for...Ch. 20 - What percentage of coolant is water? a. 80% b. 50%...Ch. 20 - Reusing old coolant is generally not approved by...Ch. 20 - A voltmeter was used to check the coolant and a...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
23.23 A highly oxidized and uneven round bar is being turned on a lathe. Would you recommend a small or a large...
Manufacturing Engineering & Technology
A number of common substances are
Some of these materials exhibit characteristics of both solid and fluid beha...
Fox and McDonald's Introduction to Fluid Mechanics
Consider a subsonic compressible flow in cartesian coordinates where the velocity potential is given by (x,y)=V...
Fundamentals of Aerodynamics
A 20-lb force is applied to the control rod AB as shown. Knowing that the length of the rod is 9 in. and that t...
Statics and Mechanics of Materials
A biological fluid moves at a flow rate of m=0.02kg/s through a coiled, thin-walled, 5-mm-diameter tube submerg...
Fundamentals of Heat and Mass Transfer
What types of polymers are most commonly blow molded?
DeGarmo's Materials and Processes in Manufacturing
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A method for killing bacteria, viruses, and protozoa in ice machines is A. sanitizing. B. cleaning. C. rinsing. D. brushing.arrow_forwardWhich of the following gases is the least dense? A.oxygen B.helium C.carbon dioxide D.argonarrow_forwardWhich beaker best illustrates what happens when the following acids are dissolved in water?a. HNO2b. HNO3c. HC1d. HFe. HC2H3O2arrow_forward
- An oil/gas separator is a pressure vessel used for separating a well stream into gaseous and liquid components. _____________greatly reduces the capacity of oil/gas separators because a much longer retention time is required to adequately separate a given quantity of foaming crude oil. a. water b. sand c. foaming d. saltsarrow_forwardA 2 inch-diameter horizontal jet of water with a velocity of 20 ft/s relative to the ground strikes a flat plate that is attached to a car moving at a velocity of Ve. After it hits, the water splatters in all directions in the plane of the plate. Investigate the effect of the car velocity V. on the force exerted on the plate.arrow_forwardWhat is required for a combustile mixture A. OXYGEN B. FUEL C. WATER PUT CHECK MARK OR CROSS MARK TO THE LETTERarrow_forward
- A supercooled water droplet turning into ice is called ____________. a. c. deposition b. e. nucleation c. d. glaciation d. a. evaporation e. b. condensationarrow_forwardDescribe the differences between CFCs, HCFCs, HFCs,and HCs.arrow_forwardSelect the type of coolant which is very toxic. O a. Mix of Long-Life ethylene glycol and Propylene glycol Ob. Ethylene glycol O c. Propylene glycol O d. Long-Life ethylene glycolarrow_forward
- Describe the difference between an azeotropic refrigerant blend and a near-azeotropic or zeotropic refrigerant blend.arrow_forwardd. Check oil level & moisture content 19. If the main wire (coil) to the distributor and the coil to the switch are broken, replace them and make sure the connections are clean and tight relevant to a. Breaking system b. Ignition system c. Ventilation system d. Combustion system 20. The required gap in ignition system between---------- a.-4 to 5 b.-0.4 to 5 c.-0.4 to 0.5 d.-4 to 0,5 |21. Which of the following is the fouled of spark plug a. Soot b. Oil c. Over heated d. All of the above |22.The suitable thread of spark plug for heavy engine is a. M19 b. M18 c. M15 d. M16 23. Using a Torque wrench, tighten the plugs to the specified torque. (Most) 4mm plugs are torqued to four kilograms per square inch. a. True b. False 24. Start the engine and evaluate its performance refers to a. Weekly Maintenance b. Annually Maintenance c. Daily Maintenance d. None of them 25. Check to see if Dynamo is working properly. If necessary, adjust the regulator refers to a. Weekly Maintenance b. Annually…arrow_forwardWhat advantage might the commercially packaged coolant material have over ice other thanit produces less mess?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Thermodynamic Availability, What is?; Author: MechanicaLEi;https://www.youtube.com/watch?v=-04oxjgS99w;License: Standard Youtube License