STRUCTURAL ANALYSIS (LL)
6th Edition
ISBN: 9780357030967
Author: KASSIMALI
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Question
Chapter 2, Problem 9P
To determine
Find the live loads acting on the girder AE and beam CD.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
3. The floor of an apartment building, shown in Fig. P2.3, is subjected to a uniformly distributed
load of 45 psf over its surface area. Determine the loads acting on the floor beams AF, BG, and
CH, and the girders AC and FH, of the framing system.
The floor system of a gymnasium consists of a 130- mm-thick concrete slab resting on four steel beams (A = 9,100 mm2) that, in turn, are supported by two steel girders (A = 25,600 mm2), as shown in Fig. P2.7. Determine the dead loads acting on beam BF and girder AD.
PROBLEMS
1002. A timber beam is reinforced with steel plates rigidly
attached at the top and bottom as shown in Fig. P-1002. By what
amount is the moment increased by the reinforcement if n = 15 and the
allowable stresses in the wood and steel are 8 MPa and 120 MPa,
respectively?
Ans. 52.2 kN-m
150
ma
w
10 mm
150
mm
250 mm
300 mm
10 mm
Chapter 2 Solutions
STRUCTURAL ANALYSIS (LL)
Knowledge Booster
Similar questions
- Given. A two-story OCBF shown in Fig. 3.40c that forms part of the building frame system in SDC E. The axial loads on the ground floor brace B1 are as follows: Dead load D= 30 kips Live load L= 15 kips Seismic force QE = ±80 kips Snow load S= 0 kips Hydrostatic load H = 0 The redundancy coefficient p = 1.1. Mapped two-second såpectral acceleration, Sps = 0.826 g. Required. Determine a pipe section for brace B1, ASTM A53 Grade B steel; F, = 35 ksi, F = 60 ksi 16 ft 16 ft Figure -15 ft B2 B1 -- -15 ft B2 B1 Ordinary concentric brace frame (OCBF) example.arrow_forwardThe roof of a single-story storage building, shown in Fig. P2.1, is subjected to a uniformly distributed load of 0.96 kPa over its surface area. Determine the loads acting on the floor beam BE and the girder AC of the framing system.arrow_forward2. A beam with an inverted U section is loaded as shown. What is the max flexural stress developed and the max beam shear developed in the beam? 30mm 30mm 2m 6m 2m 200m 250mm 40mmarrow_forward
- A doubly symmetrical I-section beam is reinforced by a flat plate attached to the upper flange as shown in Fig. P.10.3. If the resulting compound beam is subjected to a vertical shear load of 200 kN, determine the distribution of shear stress in the portion of the cross section that extends from the top of the plate to the ncutral axis. Calculate also the shcar force per unit length of bcam resisted by the shear connection between the plate and the flange of the I-section beam.arrow_forwardA 5-m long simply supported timber beam carries two concentrated loads, as shown in Figure P of the beam are shown in Figure F (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the 5-m span length. (d) Determine the maximum compression bending stress that occurs in the beam at any location within the 5-m span length. 2m 14 kN 1² 2 m 42 kN 0.5 m -x a' en Im 150 mm 100 mm H K 150 mm 450 mm The cross-sectional dimensionsarrow_forwardThe steel reinforced concrete slab shown in Fig. Q3 below has a 200mm thickness and is supported by 3 concrete beam girders at equal spacing of 9m. The deck is monolithically attached to the girders and has a total length of 20m and a width of 10m. It is reinforced with 15 x q16 steel bars across the length (19m length each bar) and 10 x p16 steel bars across the width (9m each bar). 3. 9 m Fig. Q3 (a) Assuming a nominal concrete unit weight of 25kN/m' and a steel unit weight of 78kN/m³, calculate the dead load G in kN. Consider only the deck selfweight and the selfweight of the steel reinforcement. Neglect the concrete beam girders. (b) The concrete deck carries a live load Q of 6kN/m Determine the total design load of the deck for the ultimate (ULS) and serviceability limit states (SLS) in kN (neglect the beam girders). (c) A steel column is 4m long and has a diameter of 0.50m. It is subjected to a compressive force of 20MN. Given that the, elastic modulus of the material is 210GPA,…arrow_forward
- The floor of an apartment building, shown in the figure, is subjected to a uniformly distributed load of 45 psf over its surface area. The aspect ratio (beam length to spacing ratio) of the slabs in the framing plan is 40 ft/25 ft = 1.6. The load path is: concrete slabs - floor beams - girders - columns - foundations. 1. Determine the loads acting on the floor beams AF, BG, and CH of the framing system. Sketch the tributary area of the beams selected on the building framing plan. Draw the free body diagram of the beams selected.arrow_forwardA timber beam is 15 cm deep by 10 cm wide, and carries a central load of 30 kN at the centre of a 3 m span; the beam is simply-supported at each end. The timber is reinforced with flat steel plates 10 cm wide by 1.25 cm thick bolted to the upper and lower surfaces of the beam. Taking E for steel as 200 GN/m2 and E for timber as 1 GN/m2, estimate 1. the maximum direct stress in the steel strips; - Answered (120 MN/m2.)2. the average shearing stress in the timber; - Answered (1.00 MN/m2) 3. the shearing load transmitted by the bolts; - Answered (100 kn/m)4. the bending and shearing deflections at the centre of the beam. - Answered (0.75cm) Answers must be 100kn/m for no.3 and 0.75 cm for no.4. Please show solutions to get 100 kn/m and 0.75 cm.arrow_forwardProblem 2. Determine the minimum height h of the beam shown in the figure if the flexural stress is not to exceed 20 Mpa. 1m 2.6 kN/m R₁ 6 KN 3 m 2 m R₂ 80 mm harrow_forward
- A simply supported beam of length L carries a uniformly distributed load of 6000 N/m and has the cross section shown in Fig. Find L to cause a maximum flexural stress of 16 MPa. What maximum shearing stress is then developed? 200 mm 150 mm 300 mm 250 mmarrow_forwardA small one-story reinforced concrete building is idealized for purposes of structural analysis as a massless frame supporting a total dead load of 10 kips at the beam level. The frame is 24 ft wide & 12 ft high. Each column & the beam Assume E = 3 x 103 ksi & =5 %. Determine the peak response of this frame to the El Centro ground motion. In particular, determine the peak lateral deformation at the beam level & plot the diagram of bending moments at the instant of peak response. has a 10 in square cross-section. %3Darrow_forwardFor the simply supported beam shown below, determine the internal resultant loadings at a point 1 meter to the left of point D. 6 KN 3 KN/m C 1.5 m 15m 0.5 m 0.5 marrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
