STRUCTURAL ANALYSIS (LL)
6th Edition
ISBN: 9780357030967
Author: KASSIMALI
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Question
Chapter 2, Problem 8P
To determine
Find the dead load acting on the girder AG.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
The floor system of a gymnasium consists of a 130- mm-thick concrete slab resting on four steel beams (A = 9,100 mm2) that, in turn, are supported by two steel girders (A = 25,600 mm2), as shown in Fig. P2.7. Determine the dead loads acting on beam BF and girder AD.
The roof of a single-story storage building, shown in Fig. P2.1, is subjected to a uniformly distributed load of 0.96 kPa over its surface area. Determine the loads acting on the floor beam BE and the girder AC of the framing system
PROBLEMS
1002. A timber beam is reinforced with steel plates rigidly
attached at the top and bottom as shown in Fig. P-1002. By what
amount is the moment increased by the reinforcement if n = 15 and the
allowable stresses in the wood and steel are 8 MPa and 120 MPa,
respectively?
Ans. 52.2 kN-m
150
ma
w
10 mm
150
mm
250 mm
300 mm
10 mm
Chapter 2 Solutions
STRUCTURAL ANALYSIS (LL)
Knowledge Booster
Similar questions
- The wall of a building is composed of braced W360 x 57 steel columns connected rigidly to a concrete foundation as shown above. Each column has a height of 4 m. The steel has a Young’s modulus of ? = 200 GPa and yield strength ?? = 500 MPa.a) For buckling about its strong axis (x-x), what are the support conditions at each end and what is the effective length?b) For buckling about its weak axis (y-y), what are the support conditions at each end what is the effective length?c) What is the critical load P able to be sustained by the column shown above?arrow_forward6.13 Determine the force in each member of the roof truss shown. State whether each member is in tension (T) or compression (C). 6 m -6 m 6 m 1.2 kN 2.4 kN F 2.4 kN D 1.2 kN 7.5 m B E 9 m 9 m Fig. P6.13arrow_forwardA box beam, built up as shown in Fig.. , is secured by screws spaced 5 in. apart. The beam supports a concentrated load P at the third point of a simply supported span 12 ft long. Determine the maximum value of P that will not exceed fy = 120 psi in the beam or a shearing force of 300 lb in the screws. What is the maximum flexural stress in the beam? 8 in 6 in 8 in 10 inarrow_forward
- A beam having a span of 4m is subjected to a maximum shear of 20 kN. It has a triangular cross - section having a base width of 140 mm and an altitude of 300 mm. Which of the following gives the maximum shearing stress developed on the beam? a. 1.43 MPa b. 1.80 MPa c. 1.62 MPa d. 1.78 MPaarrow_forwardA cast iron beam is of T-section as shown in Fig. 7.21. The beam is şimply supported on a span of 8 m. The beam carries a uniformly distributed load of 1.5 kN/m length on the entire span. Determine the maximum tensile and maximum compressive stresses. 100 mm 20 mm 32.23 Fmm 80 mm 100 mm 67.77 mm 20 mm- Fig. 7.21arrow_forwardA gable frame is subjected to a wind loading, as shown in Fig. 3.26. Determine the reactions at its supports due to the loadingarrow_forward
- In this structure, it has three beams 1,2,3 of length 3L. Beams 1,2,3 have a cross section area A, A, and 3A respectively. Beams 1 and 2 have a Young's modulus 3E, while beam 3 has a Young's modulus 2E. The beams are attached to some roller supports on the left and right (ignore the size of the supports). In the middle, the beams are attached to a rigid beam, which always stays perfectly vertical, and its width and mechanical property is neglected (serving only as a joint). The system is initially free of any stress. A distributed load of wintesity w0 is then applied (over a distance L) on the middle rigid beam. Calculate the normal stress in each member in terms of given variables.arrow_forwardA channel-shaped beam with an overhanging end is loaded as shown in Fig. 7-46. The material is gray cast iron having an allowable working stress of 30 MPa in tension and 120 MPa in compression. Determine the maximum allowable value of P. Also compute the shearing stress developed in the beam loaded with P computed. P 2 cт 20 ст 2P cm 2 cm 12 cm 2 m 2 m- 1 m Fig. 7-46arrow_forwardGiven. A two-story OCBF shown in Fig. 3.40c that forms part of the building frame system in SDC E. The axial loads on the ground floor brace B1 are as follows: Dead load D= 30 kips Live load L= 15 kips Seismic force QE = ±80 kips Snow load S= 0 kips Hydrostatic load H = 0 The redundancy coefficient p = 1.1. Mapped two-second såpectral acceleration, Sps = 0.826 g. Required. Determine a pipe section for brace B1, ASTM A53 Grade B steel; F, = 35 ksi, F = 60 ksi 16 ft 16 ft Figure -15 ft B2 B1 -- -15 ft B2 B1 Ordinary concentric brace frame (OCBF) example.arrow_forward
- A timber beam is 15 cm deep by 10 cm wide, and carries a central load of 30 kN at the centre of a 3 m span; the beam is simply-supported at each end. The timber is reinforced with flat steel plates 10 cm wide by 1.25 cm thick bolted to the upper and lower surfaces of the beam. Taking E for steel as 200 GN/m2 and E for timber as 1 GN/m2, estimate 1. the maximum direct stress in the steel strips; - Answered (120 MN/m2.)2. the average shearing stress in the timber; - Answered (1.00 MN/m2) 3. the shearing load transmitted by the bolts; - Answered (100 kn/m)4. the bending and shearing deflections at the centre of the beam. - Answered (0.75cm) Answers must be 100kn/m for no.3 and 0.75 cm for no.4. Please show solutions to get 100 kn/m and 0.75 cm.arrow_forward2. A beam with an inverted U section is loaded as shown. What is the max flexural stress developed and the max beam shear developed in the beam? 30mm 30mm 2m 6m 2m 200m 250mm 40mmarrow_forward3) 3. The roof system of an office building consists of a 100 mm-thick reinforced concrete slab resting on four steel beams (A =10,450 mm'), which are supported by two steel girders (A -27,700 mm'). The girders, in turn, are supported by four columns, as shown. Determine the dead loads acting on the girder AG. - 6 m Steel Steel girder (A = 27,700 mm) column - 100 mm D concrete slab 3 at 3 m =9 m F Steel floor beam (A = 10,450 mm?)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Structural Analysis (10th Edition)Civil EngineeringISBN:9780134610672Author:Russell C. HibbelerPublisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Fundamentals of Structural AnalysisCivil EngineeringISBN:9780073398006Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel LanningPublisher:McGraw-Hill Education
Traffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning
Structural Analysis (10th Edition)
Civil Engineering
ISBN:9780134610672
Author:Russell C. Hibbeler
Publisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Fundamentals of Structural Analysis
Civil Engineering
ISBN:9780073398006
Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning
Publisher:McGraw-Hill Education
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning