MindTap Engineering for Glover/Overbye/Sarma's Power System Analysis and Design, 6th Edition, [Instant Access], 1 term (6 months)
6th Edition
ISBN: 9781305636309
Author: J. Duncan Glover; Thomas Overbye; Mulukutla S. Sarma
Publisher: Cengage Learning US
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 2, Problem 2.45P
Two balanced Y-connected loads, one drawing 10 kW at 0.8 power factor lagging and the other IS kW at 0.9 power factor leading, are connected in parallel and supplied by a balanced three-phase Y-connected, 480-V source. (a) Determine the source current. (b) If the load neutrals are connected to the source neutral by a zero-ohm neutral wire through an ammeter, what will the ammeter read?
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
8. A 4-µF capacitor, a 6-uF capacitor, and an 8-μF
capacitor are in parallel across a 300-V source.
Find (a) the total capacitance, (b) the magnitude
of charge stored by each capacitor, and (c) the
total stored energy.
to be
A Full-wave rectifier is used to supply 50V D.C to a resistive load of 800 2. The diode has a
resistance of 2 N. Calculate A.C voltage across center tapped secondary.
solve for the capacitor (Filter) values of the Half-wave
Design a half-wave rectifier with a filter for the following conditions:
a) The peak input voltage is 10 V. Input frequency is 60 Hz.
b)Use virtual diode (VON = 0.7 V).
c)The minimum output voltage should be at least 90% of the maximum output voltage.
d)The load resistance may vary from 1.5 k ohm to 2.5 k ohm.
Instructions:
~ Vomax = 10 - 0.7 = 9.3 V; Vomin = 0.9xVomax;
angleV = Vomax- Vomin~ fin =60Hz; fp =60Hz.~ Use the smallest value of load resistance (1.5 k ohm) to calculate the capacitor value.~ Use the above calculated capacitor value (same value) to build 2 circuits (half-waverectifier with a filter), with load resistance of 1.5 kohm and 2.5 kohm, respectively.~ Note: The same capacitor value is applied to the load resistance of 1.5 kohm and 2.5 kohm,respectively.
Chapter 2 Solutions
MindTap Engineering for Glover/Overbye/Sarma's Power System Analysis and Design, 6th Edition, [Instant Access], 1 term (6 months)
Ch. 2 - The rms value of v(t)=Vmaxcos(t+) is given by a....Ch. 2 - If the rms phasor of a voltage is given by V=12060...Ch. 2 - If a phasor representation of a current is given...Ch. 2 - Prob. 2.4MCQCh. 2 - Prob. 2.5MCQCh. 2 - Prob. 2.6MCQCh. 2 - Prob. 2.7MCQCh. 2 - Prob. 2.8MCQCh. 2 - Prob. 2.9MCQCh. 2 - The average value of a double-frequency sinusoid,...
Ch. 2 - The power factor for an inductive circuit (R-L...Ch. 2 - The power factor for a capacitive circuit (R-C...Ch. 2 - Prob. 2.13MCQCh. 2 - The instantaneous power absorbed by the load in a...Ch. 2 - Prob. 2.15MCQCh. 2 - With generator conyention, where the current...Ch. 2 - Consider the load convention that is used for the...Ch. 2 - Prob. 2.18MCQCh. 2 - The admittance of the impedance j12 is given by...Ch. 2 - Consider Figure 2.9 of the text, Let the nodal...Ch. 2 - The three-phase source line-to-neutral voltages...Ch. 2 - In a balanced three-phase Y-connected system with...Ch. 2 - In a balanced system, the phasor sum of the...Ch. 2 - Consider a three-phase Y-connected source feeding...Ch. 2 - For a balanced- load supplied by a balanced...Ch. 2 - A balanced -load can be converted to an...Ch. 2 - When working with balanced three-phase circuits,...Ch. 2 - The total instantaneous power delivered by a...Ch. 2 - The total instantaneous power absorbed by a...Ch. 2 - Under balanced operating conditions, consider the...Ch. 2 - One advantage of balanced three-phase systems over...Ch. 2 - While the instantaneous electric power delivered...Ch. 2 - Given the complex numbers A1=630 and A2=4+j5, (a)...Ch. 2 - Convert the following instantaneous currents to...Ch. 2 - The instantaneous voltage across a circuit element...Ch. 2 - For the single-phase circuit shown in Figure...Ch. 2 - A 60Hz, single-phase source with V=27730 volts is...Ch. 2 - (a) Transform v(t)=75cos(377t15) to phasor form....Ch. 2 - Let a 100V sinusoidal source be connected to a...Ch. 2 - Consider the circuit shown in Figure 2.23 in time...Ch. 2 - For the circuit shown in Figure 2.24, compute the...Ch. 2 - For the circuit element of Problem 2.3, calculate...Ch. 2 - Prob. 2.11PCh. 2 - The voltage v(t)=359.3cos(t)volts is applied to a...Ch. 2 - Prob. 2.13PCh. 2 - A single-phase source is applied to a...Ch. 2 - Let a voltage source v(t)=4cos(t+60) be connected...Ch. 2 - A single-phase, 120V(rms),60Hz source supplies...Ch. 2 - Consider a load impedance of Z=jwL connected to a...Ch. 2 - Let a series RLC network be connected to a source...Ch. 2 - Consider a single-phase load with an applied...Ch. 2 - A circuit consists of two impedances, Z1=2030 and...Ch. 2 - An industrial plant consisting primarily of...Ch. 2 - The real power delivered by a source to two...Ch. 2 - A single-phase source has a terminal voltage...Ch. 2 - A source supplies power to the following three...Ch. 2 - Consider the series RLC circuit of Problem 2.7 and...Ch. 2 - A small manufacturing plant is located 2 km down a...Ch. 2 - An industrial load consisting of a bank of...Ch. 2 - Three loads are connected in parallel across a...Ch. 2 - Prob. 2.29PCh. 2 - Figure 2.26 shows three loads connected in...Ch. 2 - Consider two interconnected voltage sources...Ch. 2 - Prob. 2.35PCh. 2 - Prob. 2.36PCh. 2 - Prob. 2.37PCh. 2 - Prob. 2.38PCh. 2 - Prob. 2.39PCh. 2 - A balanced three-phase 240-V source supplies a...Ch. 2 - Prob. 2.41PCh. 2 - A balanced -connected impedance load with (12+j9)...Ch. 2 - A three-phase line, which has an impedance of...Ch. 2 - Two balanced three-phase loads that are connected...Ch. 2 - Two balanced Y-connected loads, one drawing 10 kW...Ch. 2 - Three identical impedances Z=3030 are connected in...Ch. 2 - Two three-phase generators supply a three-phase...Ch. 2 - Prob. 2.48PCh. 2 - Figure 2.33 gives the general -Y transformation....Ch. 2 - Consider the balanced three-phase system shown in...Ch. 2 - A three-phase line with an impedance of...Ch. 2 - A balanced three-phase load is connected to a...Ch. 2 - What is a microgrid?Ch. 2 - What are the benefits of microgrids?Ch. 2 - Prob. CCSQCh. 2 - Prob. DCSQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- For the full-wave rectifier circuit shown in Fig. below, assume ideal diodes Find: (i) d.c. output voltage (ii) peak inverse voltage PIV IDEAL 5:1 m 230 V 100 2 m IDEAL eleee earrow_forwardExample 2: calculate the RMS noise voltage arising from thermal noise in two resistors 100 & 150 resp. at T= 300°K within a bandwidth of IMHZ if: a- The resistors are connected in series. b- The resistors are connected in parallel.arrow_forward1. Determine the frequency of oscillation of a three-stage phase shift ladder network oscillator based on the following combinations of capacitance and resistance: a) C = 10 nF and R 24 kn. b) C = 50 µF and R = 800 N. c) C = 0.1 nF and R = 100 kn. d) C = 470 nF and R 12 kn. e) C = 1 µF and R = 900 0. 2. A certain cascaded amplifier arrangement has the following voltage gains: Av1 = and Av4 = 6. What is the overall voltage gain? Express each gain in decibels (dB) and determine the total voltage gain in dB.. 3.5, Av2 = 27, Av3 = 13arrow_forward
- A capacitor that has air between its plates is connected across a potential difference of 12.0 V and stores 48.0 uC of charge. What is the capacitance of the capacitor?arrow_forward7- A certain TTL gate has IH =20 µA, IL =0.1 mA, IOH =0.4 mA and IoL = 4 mA. Determine the input and output loading in the HIGH and LOW states in terms of UL. When the 1 UL (LOW state)=1.6 mA and 1 UL (HIGH state)=40 µA.arrow_forward(d) Consider a synchronous circuit with a critical path consisting of 10 logic gates, and for which the minimum logic gate delay guaranteeing a stable output is 5 milliseconds. What is the maximum clock frequency for this circuit? Justify your answer by explaining the purpose of the clock in a synchronous circuit. Provide an explanation of how you determined a suitable clock frequency for the circuit.arrow_forward
- When the electromotive force is removed from a circuit Containing inductance and resistance but no capacitors, the rate of decrease of the current is proportional to the current. If the initial current is 30 amp and it's down to 1 amp after 0.01 sec, what is the current after 0.03 sec?arrow_forwardWrite the short answer for the following: (a) What is "Seebeck Effect"? Explain (b) Explain how capacitive type of transducers can be used for pressure measurement. (c) What are the different factors which influence the choice of method used for the measurement of flow? (d) Explain briefly how small displacements can be measured by a linear or differential transformer. (e) Explain the factors which influence the response of a temperature sensing device.arrow_forwardEx) A standard two-junction thermocouple configuration is being used to measure the temperature in a wind tunnel. The reference junction is held at a constant temperature of 10 °C. We have only a thermocouple table referenced to 0 °C. Determine the output voltage when the measuring junction is exposed to an air temperature of 100 °C. Junction Temperature (°C) Output Voltage (mV) 10 0.507 20 1.019 30 1.536 40 2.058 50 2.585 60 3.115 70 3.649 80 4.186 90 4.725 100 5.268arrow_forward
- 100 2 IR R3 20 V R1 200 N E, + VR R - 200 Ω E3 10 V Is R2 100 Ω 150 mA 1. Use superposition to find the voltage (VR) and current (Ir) through the load resistor (R). 2. Find Thevenin's equivalent circuit seen between terminals a and b 3. Find Norton's equivalent circuit seen between terminals a and barrow_forward(d) It is desired to monitor the running of three fans using two light emitting diodes (LED’s). The required specification is as follows: (i) If no fan is running, no LED is to be activated. (ii) If one fan is running, the first LED is to be activated. (iii) If two fans are running, the other LED is to be activated. (iv) If three fans are running, both LED's are to be activated. Sketch a ladder logic diagram to implement this specification.arrow_forwardHomework of Amplifier 1. Assume that a 600 2, 12 µV rms voltage source is driving the amplifier in Figure 1. Determine the overall voltage gain by taking into account the attenuation in the base circuit, and find the total output voltage (ac and de). What is the phase relationship of the collector signal voltage to the base signal voltage? Voc +18 V 3.3 kN C3 V R, 47 kN C, Vin 10 μF 10 μF BDC - 75 B = 70 Figure 1 RL 10 KN R. 12 kN RE 1.0 kN 10 μFarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Database System ConceptsComputer ScienceISBN:9780078022159Author:Abraham Silberschatz Professor, Henry F. Korth, S. SudarshanPublisher:McGraw-Hill EducationStarting Out with Python (4th Edition)Computer ScienceISBN:9780134444321Author:Tony GaddisPublisher:PEARSONDigital Fundamentals (11th Edition)Computer ScienceISBN:9780132737968Author:Thomas L. FloydPublisher:PEARSON
- C How to Program (8th Edition)Computer ScienceISBN:9780133976892Author:Paul J. Deitel, Harvey DeitelPublisher:PEARSONDatabase Systems: Design, Implementation, & Manag...Computer ScienceISBN:9781337627900Author:Carlos Coronel, Steven MorrisPublisher:Cengage LearningProgrammable Logic ControllersComputer ScienceISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
Database System Concepts
Computer Science
ISBN:9780078022159
Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan
Publisher:McGraw-Hill Education
Starting Out with Python (4th Edition)
Computer Science
ISBN:9780134444321
Author:Tony Gaddis
Publisher:PEARSON
Digital Fundamentals (11th Edition)
Computer Science
ISBN:9780132737968
Author:Thomas L. Floyd
Publisher:PEARSON
C How to Program (8th Edition)
Computer Science
ISBN:9780133976892
Author:Paul J. Deitel, Harvey Deitel
Publisher:PEARSON
Database Systems: Design, Implementation, & Manag...
Computer Science
ISBN:9781337627900
Author:Carlos Coronel, Steven Morris
Publisher:Cengage Learning
Programmable Logic Controllers
Computer Science
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education
Electrical Measuring Instruments - Testing Equipment Electrical - Types of Electrical Meters; Author: Learning Engineering;https://www.youtube.com/watch?v=gkeJzRrwe5k;License: Standard YouTube License, CC-BY
01 - Instantaneous Power in AC Circuit Analysis (Electrical Engineering); Author: Math and Science;https://www.youtube.com/watch?v=If25y4Nhvw4;License: Standard YouTube License, CC-BY