Essential University Physics (3rd Edition)
3rd Edition
ISBN: 9780134202709
Author: Richard Wolfson
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 19, Problem 8FTD
A heat-pump manufacturer claims the device will heat your home using only energy already available in the ground. Is this true?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A 32% efficient electric power plant produces 900 MJ of electric energy per second and discharges waste heat into 20°C ocean water. Suppose the waste heat could be used to heat homes during the winter instead of being discharged into the ocean. A typical American house requires an average 20 kW for heating. How many homes could be heated with the waste heat of this one power plant?
The urban heat island effect is often strongest at night when temperatures would typically drop. What does this indicate about energy transfer and the material used in the building?
(a) The material in buildings releases more energy at night than it absorbs during the day
(b) The material in buildings absorbs a lot of energy during the day and when it gets colder at night the energy is released back into the cooler air.
(c) The material in buildings absorbs energy during the day and releases it because the temperature of the buildings is lower than the cooler air
(d) The material in buildings releases a lot of energy into the hot air during the day so at night all of the energy is still there
In a solar water heater, energy from the Sun is gathered by water that circulates through tubes in a rooftop collector.The solar radiation enters the collector through a transparent cover and warms the water in the tubes; this water is pumped into a holding tank. Assume that the efficiency of the overall system is 20% (that is, 80% of the incident solar energy is lost from the system). What collector area is necessary to raise the temperature of 200 L of water in the tank from 20C to 40°C in 1.0 h when the intensity of incident sunlight is 700 W/m2?
Chapter 19 Solutions
Essential University Physics (3rd Edition)
Ch. 19.1 - Which of these processes is irreversible? (a)...Ch. 19.2 - The low temperature for a practical heat engine is...Ch. 19.3 - A clever engineer decides to increase the...Ch. 19.4 - In each of the following processes, does the...Ch. 19 - Could you cool the kitchen by leaving the...Ch. 19 - Prob. 2FTDCh. 19 - Should a car get better mileage in the summer or...Ch. 19 - Prob. 4FTDCh. 19 - Name some irreversible processes that occur in a...Ch. 19 - Your power company claims that electric heat is...
Ch. 19 - A hydroelectric power plant, using the energy of...Ch. 19 - A heat-pump manufacturer claims the device will...Ch. 19 - Prob. 9FTDCh. 19 - The heat Q added during adiabatic free expansion...Ch. 19 - Energy is conserved, so why cant we recycle it as...Ch. 19 - Why doesnt the evolution of human civilization...Ch. 19 - What are the efficiencies of reversible heat...Ch. 19 - A cosmic heat engine might operate between the...Ch. 19 - A reversible Carnot engine operating between...Ch. 19 - A Carnot engine absorbs 900 J of heat each cycle...Ch. 19 - Find the COP of a reversible refrigerator...Ch. 19 - Prob. 18ECh. 19 - The human body can be 25% efficient at converting...Ch. 19 - Calculate the entropy change associated with...Ch. 19 - You metabolize a 650-kcal burger at your 37C body...Ch. 19 - You heat 250 g of water from 10C to 95C. By how...Ch. 19 - Melting a block of lead already at its melting...Ch. 19 - How much energy becomes unavailable for work in an...Ch. 19 - Prob. 25ECh. 19 - A Carnot engine extracts 745 J from a 592-K...Ch. 19 - The maximum steam temperature in a nuclear power...Ch. 19 - Youre engineering an energy-efficient house that...Ch. 19 - A power plants electrical output is 750 MW....Ch. 19 - A power plant extracts energy from steam at 280C...Ch. 19 - The electric power output of all the thermal...Ch. 19 - Consider a Carnot engine operating between...Ch. 19 - An industrial freezer operates between 0C and 32C,...Ch. 19 - Use appropriate energy-flow diagrams to analyze...Ch. 19 - Prob. 35PCh. 19 - A refrigerator maintains an interior temperature...Ch. 19 - You operate a store thats heated by an oil furnace...Ch. 19 - Use energy-flow diagrams to show that the...Ch. 19 - A heat pump extracts energy from groundwater at...Ch. 19 - A reversible engine contains 0.350 mol of ideal...Ch. 19 - (a) Determine the efficiency for the cycle shown...Ch. 19 - A 0.20-mol sample of an ideal gas goes through the...Ch. 19 - A shallow pond contains 94 Mg of water. In winter,...Ch. 19 - Estimate the rate of entropy increase associated...Ch. 19 - The temperature of n moles of ideal gas is changed...Ch. 19 - The temperature of n moles of ideal gas is changed...Ch. 19 - A 6.36-mol sample of ideal diatomic gas is at 1.00...Ch. 19 - A 250-g sample of water at 80C is mixed with 250 g...Ch. 19 - An ideal gas undergoes a process that takes it...Ch. 19 - In an adiabatic free expansion, 6.36 mol of ideal...Ch. 19 - Find the entropy change when a 2.4-kg aluminum pan...Ch. 19 - An engine with mechanical power output 8.5 kW...Ch. 19 - Find the change in entropy as 2.00 kg of H2O at...Ch. 19 - Gasoline engines operate approximately on the Otto...Ch. 19 - The compression ratio r of an engine is the ratio...Ch. 19 - In a diesel cycle, gas at volume V1 and pressure...Ch. 19 - (a) Show that the heal flowing into the diesel...Ch. 19 - Youre considering buying a car that comes in...Ch. 19 - The 54-M W wood-fired McNeil Generating Station in...Ch. 19 - A 500-g copper block at 80C is dropped into 1.0 kg...Ch. 19 - An objects heat capacity is inversely proportional...Ch. 19 - A Carnot engine extracts heat from a block of mass...Ch. 19 - In an alternative universe, youve got the...Ch. 19 - Youre the environmental protection officer for a...Ch. 19 - Find an expression for the entropy gain when hot...Ch. 19 - Problem 74 of Chapter 16 provided an approximate...Ch. 19 - The molar specific heat at constant pressure for a...Ch. 19 - Prob. 68PCh. 19 - Energy-efficiency specialists measure the heat Qh...Ch. 19 - Refrigerators remain among the greatest consumers...Ch. 19 - The refrigerators COP is a. 13. b. 2. c. 3. d. 4.Ch. 19 - The fuel energy consumed at the power plant to run...Ch. 19 - Prob. 73PP
Additional Science Textbook Solutions
Find more solutions based on key concepts
At the right is a sketch showing one of the atoms in the diffuse, cool cloud of gas described in the previous q...
Lecture- Tutorials for Introductory Astronomy
The figure shows a cube of side s in a uniform electric field E. (1) Whats the flux through each of the three c...
Essential University Physics: Volume 2 (3rd Edition)
A police radars effective range is 1.0 km, and your radar detectors range is 1.9 km. Youre going 110 km/h in a ...
Essential University Physics: Volume 1 (3rd Edition)
Q37.2 If simultaneity is not an absolute concept, does that mean that we must discard the concept of causality?...
University Physics with Modern Physics (14th Edition)
42. Entrance and exit ramps for freeways are often circular stretches of road. As you go around one at a consta...
College Physics: A Strategic Approach (4th Edition)
The given sentence.
Glencoe Physical Science 2012 Student Edition (Glencoe Science) (McGraw-Hill Education)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- Why is a person able to remove a piece of dry aluminum foil from a hot oven with bare fingers, whereas a burn results if there is moisture on the foil?arrow_forwardA heat pump used for heating shown in Figure P18.25 is essentially an air conditioner installed backward. It extracts energy from colder air outside and deposits it in a warmer room. Suppose the ratio of the actual energy entering the room to the work done by the devices motor is 10.0% of the theoretical maximum ratio. Determine the energy entering the room per joule of work done by the motor given that the inside temperature is 20.0C and the outside temperature is 5.00C. Figure P18.25arrow_forwardA certain steel railroad rails 13 yd in length and weighs 70.0 lb/yd How much thermal energy is required to increase the length of such a rail by 3.0 mm? .Note: Assume the steel has the same specific heal as iron.arrow_forward
- A heat pump has a coefficient of performance of 3.80 and operates with a power consumption of 7.03 103 W. (a) How much energy does it deliver into a home during 8.00 h of continuous operation? (b) How much energy does it extract from the outside air?arrow_forwardYou are working on a summer job at a company that designs non-traditional energy systems. The company is working on a proposed electric power plant that would make use of the temperature gradient in the ocean. The system includes a heat engine that would operate between 20.0C (surface-water temperature) and 5.00C (water temperature at a depth of about 1 km). (a) Your supervisor asks you to determine the maximum efficiency of such a system. (b) In addition, if the electric power output of the plant is 75.0 MW and it operates at the maximum theoretically possible efficiency, you must determine the rate at which energy is taken in from the warm reservoir. (c) From this information, if an electric bill for a typical home shows a use of 950 kWh per month, your supervisor wants to know how many homes can be provided with power from this energy system operating at its maximum efficiency. (d) As energy is drawn from the warm surface water to operate the engine, it is replaced by energy absorbed from sunlight on the surface. If the average intensity absorbed from sunlight is 650 W/m2 for 12 daylight hours on a clear day, you need to find the area of the ocean surface that is necessary for sunlight to replace the energy absorbed into the engine. (e) From this information, you need to determine if there is enough ocean surface on the Earth to use such engines to supply the electrical needs for all the homes associated with the Earths population. Assume the energy use for a home in part (c) is an average over the entire planet. (f) In view of your results in this problem, your supervisor has asked for your conclusion as to whether such a system is worthwhile to pursue. Note that the fuel (sunlight) is free.arrow_forwardA resting adult of average size converts chemical energy in food into internal energy at the rate 120 W, called her basal metabolic rate. To stay at constant temperature, the body must put out energy at the same rate. Several processes exhaust energy from your body. Usually, the most important is thermal conduction into the air in contact with your exposed skin. If you are not wearing a hat, a convection current of warm air rises vertically from your head like a plume from a smokestack. Your body also loses energy by electromagnetic radiation, by your exhaling warm air, and by evaporation of perspiration. In this problem, consider still another pathway for energy loss: moisture in exhaled breath. Suppose you breathe out 22.0 breaths per minute, each with a volume of 0.600 L. Assume that you inhale dry air and exhale air at 37C containing water vapor with a vapor pressure of 3.20 kPa. The vapor came from evaporation of liquid water in your body. Model the water vapor as an ideal gas. Assume that its latent heat of evaporation at 37C is the same as its heat of vaporization at 100C. Calculate the rate at which you lose energy by exhaling humid air.arrow_forward
- The U.S. Department of Energy estimates that up to 10 percent of the energy use of a house can be saved by caulking and weatherstripping doors and windows to reduce air leaks at a cost of about $90 for materials for an average home with 12 windows and 2 doors. Caulking and weatherstripping every gas-heated home properly would save enough energy to heat about 4 million homes. The savings can be increased by installing storm windows. Determine how long it will take for the caulking and weatherstripping to pay for itself from the energy they save for a house whose annual energy use is $1500.arrow_forwardWould you be willing to financially back an inventor who is marketing a device that she claims has 25 kJ of heat transfer at 600 K, has heat transfer to the environment at 300 K, and does 12 kJ of work? Explain your answer.arrow_forwardA prototype power generation device that cycles steam between a geothermal source (temperature 393 K) and a cooling tower (temperature 280 K) has a theoretical maximum efficiency ofarrow_forward
- An inventor claims to have developed a heat pump that produces a 200-kW heating effect for a 293 K heated zone while only using 75 kW of power and a heat source at 273 K. Justify the validity of this claim.arrow_forwardA heat pump is used to maintain a house at 25°C by extracting heat from the outside air on a day when the outside air temperature is 4°C. The house is estimated to lose heat at a rate of 110,000 kJ/h, and the heat pump consumes 4.75 kW of electric power when running. Is this heat pump powerful enough to do the job?arrow_forwardA heat pump is used to maintain a house at a constant temperature of 23°C. The house is losing heat to the outside air through the walls and the windows at a rate of 85,000 kJ/h while the energy generated within the house from people, lights, and appliances amounts to 4000 kJ/h. For a COP of 3.2, determine the required power input to the heat pump.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Physics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
College PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage Learning
Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
College PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers, Technology ...
Physics
ISBN:9781305116399
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
College Physics
Physics
ISBN:9781285737027
Author:Raymond A. Serway, Chris Vuille
Publisher:Cengage Learning
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
College Physics
Physics
ISBN:9781305952300
Author:Raymond A. Serway, Chris Vuille
Publisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...
Physics
ISBN:9781337553292
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
The Second Law of Thermodynamics: Heat Flow, Entropy, and Microstates; Author: Professor Dave Explains;https://www.youtube.com/watch?v=MrwW4w2nAMc;License: Standard YouTube License, CC-BY