Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
6th Edition
ISBN: 9780135257272
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 17, Problem 8CQ
To determine
Mention the inflation pressure specification that must be used when correcting or checking tire pressure.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
All of the following statements are correct except?a. Tire inflation pressure directly affects traction.b. The recommended tire pressure for front andrear tires may be different.c. The recommended tire pressures are oftenlower than maximum pressures.d. The recommended tire pressure is moldedinto the sidewall of the tire
Which of the following would NOT be cause for rejection when checking the tire condition?
Any tire has a fabric break or cut exposing ply or cord or any tire is in contact with the body or frame.
Any tire tread or recap is separated or any tire is flat.
All of the statements shown are cause for rejection.
Any tire has any bumps, bulges, or knots or is repaired with a boot or blowout patch.
what is the formula to measure gas from tire interior?
Chapter 17 Solutions
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Ch. 17 - Why should brake fluid not be filled above the...Ch. 17 - Why should brake fluid be kept in an airtight...Ch. 17 - How do you check differential fluid?Ch. 17 - What are four lubricants that a manual...Ch. 17 - How often does diesel exhaust fluid (DEF) need to...Ch. 17 - Prob. 1CQCh. 17 - When should the engine oil be replaced? a....Ch. 17 - Prob. 3CQCh. 17 - Routine service includes ____________. a. checking...Ch. 17 - Which of these conditions must be met before...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- All of the following statements are correct except? a. Tire inflation pressure directly affects traction. b. The recommended tire pressure for front and rear tires may be different. c. The recommended tire pressures are often lower than maximum pressures. d. The recommended tire pressure is molded into the sidewall of the tire.arrow_forwardWhich of the following statements about sidewall markings is correct? a. The load index is given as a letter. b. The traction and temperature ratings are based on the speed rating of the tire. c. The tires recommended inflation pressure and load are indicated. d. The DOT code indicates when and where the tire was made.arrow_forwardHow does a technician determine the proper inflation for a vehicle's tires?arrow_forward
- Technician A says that replacement wheel rims should be the same as the original equipment wheels in load capacity, offset, width, diameter, and mounting configuration. Technician B says that if wheels are installed that have a different stock width or diameter, make sure to use a tire that has the same overall width as the original tires. Otherwise the vehicles wheel-speed sensors, speedometer, antiock brake system, and many other systems will be affected. Who is correct? a. Technician A only b. Technician B only c. Both A and B Neither A nor Barrow_forwardA P195/75R14 tire classification includes both metric and English standard measurements. True Falsearrow_forwardDescribe the proper procedure to seal a puncture in a tire.arrow_forward
- A front tire has excessive wear on both edges of the tire tread. The most likely cause of this problem is ______. a. overinflation b. underinflation c. improper static balance d. improper dynamic balancearrow_forwardWhile performing a prealignment inspection: Technician A says that improper front-wheel bearing adjustment may affect wheel alignment angles. Technician B says that worn ball joints affect only the camber angle. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardAn indirect TPMS is being discussed. Technician A says that if a specific tire is low, the system will typically alert the driver which tire is low. Technician B says that after serving the indirect TPMS, you need to perform a re-learn procedure. Who is correct? Technician A Technician B Both Technician A and B Neither Technician A or Barrow_forward
- While discussing pull during braking: Technician A says that this can be caused by one tire being underinflated. Technician B says that a frozen wheel cylinder on one side of the car can cause this. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forward108) Technician A says that engine management malfunctions may be misinterpreted as transmission malfunction. Technician B says that imbalance in driveline components or wheels may be a likely cause of vibration. Which technician is correct? O Technician A O Technician B O Both technicians A and B O Neither technician A nor Barrow_forwardWhile diagnosing the cause of noise from a transfer case: Technician A says that a probable cause is incorrect tire size. Technician B says that the most probable cause is a faulty bearing or gear. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,