Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Question
Chapter 16, Problem 5ASRQ
To determine
While measuring resistance with an ohmmeter: The technician with correct approach.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
1)Couplings is an instrument used to protect overload between two power transmitting shafts.
Select one:
True
False
2)"Thimble" is a part of the Micrometer.
Select one:
True
False
Lubrication is a method to reduce wear on surfaces that are not in close contact and act as a seal to reduce noise.
Select one: True
False
True false or neither true or false
Chapter 16 Solutions
Automotive Technology
Ch. 16 - How will an electrical circuit behave if there is...Ch. 16 - What happens to an electrical circuit when there...Ch. 16 - Prob. 3SACh. 16 - What type of solder should be used to repair...Ch. 16 - True or False? The MIN/MAX function on some DMMs...Ch. 16 - True or False? A zero reading on an ohmmeter means...Ch. 16 - Prob. 3TFCh. 16 - While troubleshooting a problem, the key to...Ch. 16 - Prob. 5TFCh. 16 - Prob. 1MC
Ch. 16 - Prob. 2MCCh. 16 - Wiring harnesses are typically shielded by plastic...Ch. 16 - Which of the following lab scope controls must be...Ch. 16 - Prob. 5MCCh. 16 - Which of the following information is not given in...Ch. 16 - While discussing electricity: Technician A says...Ch. 16 - While discussing NTC thermistors: Technician A...Ch. 16 - While measuring the resistance of a wire with an...Ch. 16 - While testing variable resistors: Technician A...Ch. 16 - Prob. 5ASRQCh. 16 - Technician A uses a testlight to test circuit...Ch. 16 - Technician A uses a testlight to detect...Ch. 16 - While diagnosing the location of a wire-to-wire...Ch. 16 - While measuring resistance: Technician A uses an...Ch. 16 - While discussing how to test a switch: Technician...
Knowledge Booster
Similar questions
- While measuring resistance: Technician A uses an ohmmeter to measure resistance of a component before disconnecting it from the circuit. Technician B uses a voltmeter to measure voltage drop. A circuit with very low resistance will drop zero or very little voltage. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile measuring the resistance of a wire with an ohmmeter: Technician A says that if low resistance is shown on the meter, the wire is shorted. Technician B says that if no resistance is measured, the wire is shorted. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forwardTrue or False? A lab scope is a visual voltmeter that shows voltage over a period of time.arrow_forward
- While checking an A/C compressor clutch coil clamping diode with a DMM, the meter shows infinite resistance when the diode is measured in both directions: Technician A says that the diode is open. Technician B says that all diodes should behave this way until a specified voltage is applied to them. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardTechnician A uses a testlight to detect resistance. Technician B uses a jumper wire to test circuit breakers, relays, and lights. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue or False? A zero reading on an ohmmeter means the circuit or component is open.arrow_forward
- Technician A uses a testlight to test circuit protection devices. Technician B uses a voltmeter to test circuit protection devices. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile checking an A/C compressor clutch coil spikesuppressing diode with an ohmmeter, the meter shows infinite resistance when the diode is measured in both directions: Technician A says that the diode is open. Technician B says that all diodes should behave this way until a specified voltage is applied to them. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue or False? A bad ground can cause an increase in the reference voltage to a sensor.arrow_forward
- While discussing diagnostic procedures: Technician A says that after the visual inspection has been performed, the DTCs should be cleared from the memory of the PCM. Technician B says that serial data can be helpful when there are no DTCs but there is a fault in the system. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardAll gauges operate but read lower than normal: Technician A says that the connection to the instrument cluster may be corroded. Technician B says that the cluster s IVR may be open. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue or False? The same information available in service manuals and bulletins may also be available electronically on DVDs and the Internet.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning