Explanation Given information: The A992 steel beam has a moment of inertia of I = 125 ( 10 6 ) mm 4 Method adopted: Castigliano’s theorem. Assumptions: Young’s modulus of the A992 steel beam is E = 200 × 10 6 kN/m 2 . Explanation: Castigliano’s theorem to determine the slope for the beam is as follows: θ = ∫ 0 L M ( ∂ M ∂ M ′ ) d x E I (1) Here, θ is the slope of the tangent θ at a point on the elastic curve is to be determined, M is internal moment in the beam, expressed as a function of x and caused by both the force P and the actual loads on the beam, M ′ is the external moment, E is modulus of elasticity of a member, and I is moment of inertia of the cross-sectional area about the neutral axis. Internal moment in the beam ( M ): Apply external moment M ′ at the point where the slope is to be determined. Determine the reactions: Entire beam: Show the free-body diagram of the entire beam as in Figure 1. Moment about point B : Determine the vertical reaction at point C by taking moment about point B . ∑ M B = 0 C y ( 6 ) + 18 + M ′ − 18 = 0 (2) Along the vertical direction: Determine the vertical reaction at point B by resolving the vertical component of forces. ∑ F y = 0 B y + C y = 0 (3) Along the horizontal direction: Determine the horizontal reaction at point C by resolving the horizontal component of forces. ∑ F x = 0 C x = 0 Show the calculation of values as follows: Solve Equation (2). C y ( 6 ) = − M ′ C y = − M ′ 6 Substitute ( − M ′ 6 ) for C y in Equation (3). B y − M ′ 6 = 0 B y = M ′ 6 Region 0 ≤ x < 4 m from left end: Show the free body diagram of the beam for the region 0 ≤ x < 4 m as in Figure 2. Moment about the section: Determine the moment at the section by taking moment about the section. ∑ M x 1 = 0 M 1 + 18 = 0 (4) SolveEquation (4). M 1 = − 18 kN-m . Region 4 m < x < 10 m from left end: Show the free body diagram of the beam for the region 4 m < x < 10 m as in Figure 3. Moment about the section: Determine the moment at the section by taking moment about the section. ∑ M x 2 = 0 M 2 + 18 − B y ( x 2 ) + M ′ = 0 (5) Substitute M ′ 6 for B y in Equation (5). M 2 + 18 − M ′ 6 ( x 2 ) + M ′ = 0 M 2 = M ′ x 2 6 − 18 − M ′ Region 10 m < x ≤ 14 m : Show the free body diagram of the beam for the region 10 m < x ≤ 14 m as in Figure 4. Moment about the section: Determine the moment at the section by taking moment about the section. ∑ M x 3 = 0 − M 3 − 18 = 0 (6) Solve Equation (6). M 3 = − 18 kN-m Calculation: Tabulate the calculated values as in Table 1. Limit (m) M ∂ M ∂ M ′ M ( M ′ = 0 ) 0 ≤ x < 4 M 1 = − 18 kN-m ∂ M 1 ∂ M ′ = 0 M 1 = − 18 kN-m 4 < x < 10 M 2 = M ′ x 2 6 − 18 − M ′ ∂ M 2 ∂ M ′ = − 1 + x 2 6 M 2 = − 18 kN-m 10 < x ≤ 14 M 3 = − 18 kN-m ∂ M 3 ∂ M ′ = 0 M 3 = − 18 kN-m Rearrange the Equation (1)

9th Edition

ISBN: 9780133254426

Author: Russell C. Hibbeler

Publisher: Prentice Hall

See similar textbooks

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and af…

Videos

Question

Chapter 14.10, Problem 14.140P

To determine

The slope at B.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 14.10, Problem 14.139P

Chapter 14.10, Problem 14.141P

Students have asked these similar questions

Continuity equation A y x dx D T معادلة الاستمرارية Ly X Q/Prove that ди хе + ♥+ ㅇ? he me ze ོ༞“༠ ?

Q Derive (continuity equation)? I want to derive clear mathematics.

motor supplies 200 kW at 6 Hz to flange A of the shaft shown in Figure. Gear B transfers 125 W of power to operating machinery in the factory, and the remaining power in the shaft is mansferred by gear D. Shafts (1) and (2) are solid aluminum (G = 28 GPa) shafts that have the same diameter and an allowable shear stress of t= 40 MPa. Shaft (3) is a solid steel (G = 80 GPa) shaft with an allowable shear stress of t = 55 MPa. Determine: a) the minimum permissible diameter for aluminum shafts (1) and (2) b) the minimum permissible diameter for steel shaft (3). c) the rotation angle of gear D with respect to flange A if the shafts have the minimum permissible diameters as determined in (a) and (b).

Chapter 14 Solutions

Mechanics of Materials

Ch. 14.2 - A material is subjected to a general state of...Ch. 14.2 - The strain-energy density for plane stress must be...Ch. 14.2 - 14–3. Determine the strain energy in the stepped...Ch. 14.2 - Prob. 14.4P Ch. 14.2 - Using bolts of the same material and...Ch. 14.2 - If P = 60 kN, determine the total strain energy...Ch. 14.2 - Determine the maximum force P and the...Ch. 14.2 - *14–8. Determine the torsional strain energy in...Ch. 14.2 - Determine the torsional strain energy in the A-36...Ch. 14.2 - The shaft assembly is fixed at C. The hollow...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The slope at B .

Solution Summary: The author explains Castigliano's theorem to determine the slope for the A992 steel beam.

Concept explainers

Videos

The slope at B.

Want to see the full answer?

Chapter 14 Solutions