Materials Science And Engineering Properties
1st Edition
ISBN: 9781111988609
Author: Charles Gilmore
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 13, Problem 2CQ
To determine
Theprocess in powder fabrication of metal and cermaics, when the pressed powder is part is sintered, the particle bond to each other.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Normal stress of alumi
Which of the following is correct when we increase the volume fraction
porosity of a ceramic material?
both the flexural strength and modulus of elasticity decreases
flexural strength decreases, while modulus of elasticity increases
flexural strength increases, while modulus of elasticity decreases
both the flexural strength and modulus of elasticity increases
In an engineering application, the material is a strip of iron with a fixed crystallographic structure subject to a tensile load during operation. The part
failed (yielded) during operation and needs to be replaced with a component with better properties. You are told that two other iron strips had failed
at yield stresses of 110 and 120 MPa, with grain sizes of 30 microns and 25 microns respectively. The current strip has a grain size of 20 microns. The
diameter of the rod is 1 mm and the load applied is 100 N. What is the yield stress of the new part C and would you recommend it for operation?
Select one:
Oa. 133.5 MPa, yes
O b.
OC.
Od
Oe.
120.5 MPa, no
129.5, yes
140.5, no
123.5 MPa, yes
Chapter 13 Solutions
Materials Science And Engineering Properties
Ch. 13 - Prob. 1CQCh. 13 - Prob. 2CQCh. 13 - Prob. 3CQCh. 13 - Prob. 4CQCh. 13 - Prob. 5CQCh. 13 - Prob. 6CQCh. 13 - Prob. 7CQCh. 13 - Prob. 8CQCh. 13 - Prob. 9CQCh. 13 - Prob. 10CQ
Ch. 13 - Prob. 11CQCh. 13 - Prob. 12CQCh. 13 - Prob. 13CQCh. 13 - Prob. 14CQCh. 13 - Prob. 15CQCh. 13 - Prob. 16CQCh. 13 - Prob. 17CQCh. 13 - Prob. 18CQCh. 13 - Prob. 19CQCh. 13 - Prob. 1ETSQCh. 13 - Prob. 2ETSQCh. 13 - Prob. 3ETSQCh. 13 - Prob. 4ETSQCh. 13 - Prob. 5ETSQCh. 13 - Prob. 6ETSQCh. 13 - Prob. 7ETSQCh. 13 - Prob. 8ETSQCh. 13 - Prob. 9ETSQCh. 13 - Prob. 10ETSQCh. 13 - Prob. 11ETSQCh. 13 - Prob. 12ETSQCh. 13 - Prob. 13ETSQCh. 13 - Prob. 14ETSQCh. 13 - Prob. 15ETSQCh. 13 - Prob. 16ETSQ
Knowledge Booster
Similar questions
- 9.5 The following thermal bimorph is made of Silicon with a thermal conductivity k = 130 W/(m°C), Young's modulus E = 200 GPa, Poisson's ratio v = 0.27, and ther- mal expansion coefficient a = 2.6 × 10-6/°C. It is 1 mm thick with fixed tempera- tures of 60°C and 10°C, respectively, at the leftmost ends of its hot arm and cold arm, as shown below. Suppose the bimorph has a uniform internal heat genera- tion at 100 W/m³, and ignore the effects of convective heat transfer. (1) Determine the steady-state temperature distribution in the thermal bimorph. (2) Determine the thermally induced deformation and stresses in the bimorph if the two arms are fixed on their left ends. Hot arm Thot = 60°C Cold arm Tcold = 10°C All dimensions are in millimeters. 6.000- 3.000 2.000 2.000 200 12.000 5.000 3.000arrow_forwardWhich of the following statements is incorrect about ceramics? A Ceramics have very weak interatomic bonding. (B) Ceramics have a low coefficient of thermal expansion © Ceramics can be crystalline or nanocrystalline (amorphous). (D Ceramics can be used as a matrix material in composites.arrow_forward
Recommended textbooks for you
Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning