Welding: Principles and Applications (MindTap Course List)
8th Edition
ISBN: 9781305494695
Author: Larry Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 13, Problem 21R
Why should there be a space between the plates when making a fillet weld on thick plates of a tee joint?
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Show all work. Indicate the origin that is used for each plane.
Identify the Miller indices for the following planes.
N
23
1
A)
X
B)
y
the following table gives weight gain time data for the oxidation of some metal at an elevated temperature
W(mg/cm2). Time (min)
4.66 20
11.7 50
41.1 175
a) determin whether the oxidation kinetics obey a linear, parabolic, or logarithmic rate expression.
b) Now compute W after a time of 1000 min
A cylindrical specimen of aluminum is pulled in tension. Use the stress v. strain plot below
for this specimen of Al to answer parts (a) - (f). Hint: Each strain increment is 0.004.
Be sure to include your engineering problem solving method per the class rubric.
400
350
300
250
Stress
(MPa) 200
150
100
50
Aluminum (Stress v. Strain)
0
0
0.02
0.04
0.06
0.08
Strain
0.1
0.12
0.14
0.16
a. Compute the modulus of elasticity.
b. Determine the yield strength at a strain offset of 0.002.
c. Determine the tensile strength of this metal.
d. Compute the ductility in percent elongation.
e. Compute the modulus of resilience.
f. Determine the elastic strain recovery for an unloaded stress of 340 MPa.
Chapter 13 Solutions
Welding: Principles and Applications (MindTap Course List)
Ch. 13 - Why is it important to make sure that an FCA...Ch. 13 - What major safety concerns should an FCA welder be...Ch. 13 - Why should the FCA welding practice plates be...Ch. 13 - Why should the FCA welds be of substantial length?Ch. 13 - What must be done to a shielding gas cylinder...Ch. 13 - What can happen to the wire if the conduit is...Ch. 13 - Why is it a good idea for a new student welder to...Ch. 13 - Why is the curl in the wire end straightened out?Ch. 13 - What problems can a high-feed roller pressure...Ch. 13 - Referring to Table 13-1, answer the following a....
Ch. 13 - What are the disadvantages of beveling plates for...Ch. 13 - What is the maximum plate thickness that an FCS...Ch. 13 - What is the smallest V-groove angle that can be...Ch. 13 - What is the purpose of the root pass?Ch. 13 - Why is the FCA welding process not used for...Ch. 13 - Why should convex weld faces be avoided?Ch. 13 - What bead pattern is best for overhead welds?Ch. 13 - Why is the appearance of the cover pass so...Ch. 13 - What are the visual inspection standard's...Ch. 13 - Why is the backing strip 2 in. (50 mm) longer than...Ch. 13 - Why should there be a space between the plates...Ch. 13 - What would a small notch at the root weld's...Ch. 13 - What changes should be made in the setup for...Ch. 13 - What problem must be overcome if the amperage and...Ch. 13 - How can higher welding speeds help control...Ch. 13 - How can spatter buildup on the welding gun be...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Consider a single crystal of silver oriented such that a tensile stress is applied along a [112] direction. If slip occurs on a (011) plane and in a [111] direction and is initiated at an applied tensile stress of 15.9 MPa, compute the critical resolved shear stress.arrow_forwardA hypothetical component must not fail when a tensile stress of 15.25 MPa is applied. Determine the maximum allowable internal crack length if the surface energy of the component is 1.50 J/m2. Assume a modulus of elasticity of 350 GPa.arrow_forwardFresh air at 21.1 C in which partial pressure of water vapor is 0.018 atmosphere is blown at the rate of 214 m3/h first through a preheater and then adiabatically saturated in spray chambers to 100% saturation and again reheated this reheated air has humidity of 0.024 kg water vapor per kg dry air. It is assumed that the fresh air and the air leaving the re-heater have the same percentage humidity. Determine:- a- The temperature of preheater, spray-chamber and re-heater b- Heat requirement for preheating and re-heating 11:39 مarrow_forward
- Example(3): 0.15 kg/s steam at atmospheric pressure and superheated to 400 K is bled into an air stream at 320 K and 20 per cent relative humidity. What is the temperature, enthalpy, and relative humidity of the mixed stream if the air is flowing at 5 kg/ s? How much steam would be required to provide an exit temperature of 330 K and what would be the humidity of this mixture? 11:39 مarrow_forwardThe answer to the problem is 31.3rad/s. Please show me how to get the final answerarrow_forwardThe answer to the problem is 1.00 m/s^2. Please show me how to get the final answerarrow_forward
- The answer to the problem is 0.30. Please show me how to get the final answerarrow_forwardThe answer to the problem is 1.96 m/s. Please show me how to get the final answerarrow_forwardA cylindrical tank of diameter D is currently filled with water to a height h, as shown in the figure to the right. Water enters the tank through the pipe at (1) with a cross-sectional area A₁ and a uniform velocity V₁. The height of water in the tank is increasing at a constant rate of 5 mm/s. Given the parameters below, find the volumetric flow rate in the pipe at (2), V2, in cm³/s, and classify it as an inflow or outflow. D = 20 cm h = 0.5 m A₁ = 1 cm² V₁ = 0.1 m/s h 1 V₁ D Pwater = 1,000 kg/m³ V2 2arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Differences between Temporary Joining and Permanent Joining.; Author: Academic Gain Tutorials;https://www.youtube.com/watch?v=PTr8QZhgXyg;License: Standard Youtube License