Explanation Given information: The modulus of elasticity of the shaft ( E ) is 200 GPa . The diameter of the shaft ( d ) is 30 mm . The point load act at a first pulley of the shaft ( P 1 ) is 150 N . The point load act at a second pulley of the shaft ( P 2 ) is 60 N . The point load act at a third pulley of the shaft ( P 3 ) is 150 N . The moment of inertia of the shaft is I . The length of the shaft ( L ) is 1000 mm . Calculation: Show the free body diagram of the shaft as in Figure 1. Refer Figure 1. Calculate the support reactions A and B ( R A and R B ) : Calculate the vertical forces by applying the equation of equilibrium: Sum of vertical forces is equal to 0. ∑ F y = 0 R A + R B − 150 − 60 − 150 = 0 R A + R B − 360 = 0 R A + R B = 360 (1) Calculate the moment about point A by applying the equation of equilibrium: Sum of moments about point A is equal to 0. ∑ M A = 0 ( R B × 1000 ) − ( 150 × 250 ) − ( 60 × 500 ) − ( 150 × 750 ) = 0 1 , 000 R B − 180 , 000 = 0 1 , 000 R B = 180 , 000 R B = 180 , 000 1 , 000 R B = 180 N Substitute 180 N for R B in Equation (1). R A + 180 = 360 R A = 360 − 180 R A = 180 N Calculate the moment function with respect of the x distance M ( x ) : M ( x ) = [ − ( − 180 ) ( x − 0 ) − 150 ( x − 0.25 ) − 60 ( x − 0.5 ) − 150 ( x − 0.75 ) ] = [ 180 x − 150 ( x − 0.25 ) − 60 ( x − 0.5 ) − 150 ( x − 0.75 ) ] Elastic Curve and slope is as follows: E I d 2 υ d x 2 = M ( x ) (2) Substitute [ − 180 x − 150 ( x − 0.25 ) − 60 ( x − 0.5 ) − 150 ( x − 0.75 ) ] for M ( x ) in Equation (2). E I d 2 υ d x 2 = [ 180 x − 150 ( x − 0.25 ) − 60 ( x − 0.5 ) − 150 ( x − 0.75 ) ] (3) Integrate both sides of the Equation (3). E I d υ d x = [ 180 2 x 2 − 150 2 ( x − 0.25 ) 2 − 60 2 ( x − 0.5 ) 2 − 150 2 ( x − 0.75 ) 2 + C 1 ] = [ 90 x 2 − 75 ( x − 0.25 ) 2 − 30 ( x − 0.5 ) 2 − 75 ( x − 0.75 ) 2 + C 1 ] (4) Integrate both sides of the Equation (4). E I υ = [ 90 3 x 3 − 75 3 ( x − 0.25 ) 3 − 30 3 ( x − 0.5 ) 3 − 75 3 ( x − 0.75 ) 3 + C 1 x + C 2 ] = [ 30 x 3 − 25 ( x − 0.25 ) 3 − 10 ( x − 0.5 ) 3 − 25 ( x − 0.75 ) 3 + C 1 x + C 2 ] (5) Boundary conditions are as follows: υ = 0 at x = 0 υ = 0 at x = 1 m Apply the first boundary condition in Equation (5)

9th Edition

ISBN: 9780133254426

Author: Russell C. Hibbeler

Publisher: Prentice Hall

See similar textbooks

Concept explainers

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft …

Question

Chapter 12.3, Problem 12.46P

To determine

The slope of the shaft at A (θA) .

The slope of the shaft at B (θB) .

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 12.3, Problem 12.45P

Chapter 12.3, Problem 12.47P

Students have asked these similar questions

-6- 8 من 8 Mechanical vibration HW-prob-1 lecture 8 By: Lecturer Mohammed O. attea The 8-lb body is released from rest a distance xo to the right of the equilibrium position. Determine the displacement x as a function of time t, where t = 0 is the time of release. c=2.5 lb-sec/ft wwwww k-3 lb/in. 8 lb Prob. -2 Find the value of (c) if the system is critically damping. Prob-3 Find Meq and Ceq at point B, Drive eq. of motion for the system below. Ш H -7~ + 目 T T & T тт +

Q For the following plan of building foundation, Determine immediate settlement at points (A) and (B) knowing that: E,-25MPa, u=0.3, Depth of foundation (D) =1m, Depth of layer below base level of foundation (H)=10m. 3m 2m 100kPa A 2m 150kPa 5m 200kPa B

W PE 2 43 R² 80 + 10 + kr³ Ø8=0 +0 R²+J+ kr200 R² + J-) + k r² = 0 kr20 kr20 8+ W₁ = = 0 R²+1) R²+J+) 4 lec 8.pdf Mechanical vibration lecture 6 By: Lecturer Mohammed C. Attea HW1 (Energy method) Find equation of motion and natural frequency for the system shown in fig. by energy method. m. Jo 000 HW2// For the system Fig below find 1-F.B.D 2Eq.of motion 8 wn 4-0 (1) -5- m

Chapter 12 Solutions

Mechanics of Materials

Ch. 12.2 - In each case, determine the internal bending...Ch. 12.2 - Determine the slope and deflection of end A of the...Ch. 12.2 - Determine the slope and deflection of end A of the...Ch. 12.2 - Determine the slope of end A of the cantilevered...Ch. 12.2 - Determine the maximum deflection of the simply...Ch. 12.2 - Determine the maximum deflection of the simply...Ch. 12.2 - Determine the slope of the simply supported beam...Ch. 12.2 - An L2 steel strap having a thickness of 0.125 in....Ch. 12.2 - The L2 steel blade of the band saw wraps around...Ch. 12.2 - A picture is taken of a man performing a pole...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The slope of the shaft at A ( θ A ) . The slope of the shaft at B ( θ B ) .

Concept explainers

The slope of the shaft at A (θA) . The slope of the shaft at B (θB) .

Want to see the full answer?

Chapter 12 Solutions

The slope of the shaft at A (θA) .

The slope of the shaft at B (θB) .