Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 12, Problem 6MC
Which of the following is not a type of valve guide seal?
- Positive
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The spool is sealed along the
clearance between moving spool
and
O housing (valve body)
case
cylinder
O pipe
*
Three way valves has one
pressure port, one tank port
and one actuating port
True O
False O
Directional control valves can bypass, start, stop, sequence and interlock actuator
movement.
True
False
Chapter 12 Solutions
Automotive Technology
Ch. 12 - Explain staged and continuously variable value...Ch. 12 - Prob. 2SACh. 12 - Define valve margin.Ch. 12 - What usually causes warpage in an aluminum cylin...Ch. 12 - What are the two ways pushrods can be checked for...Ch. 12 - True False? Fiats MultiAir system relies on...Ch. 12 - True False? Camshaft straightness is checked using...Ch. 12 - Which of the following is not true of knurling? It...Ch. 12 - To allow the engine to run on the Atkinson cycle,...Ch. 12 - To ensure proper seating of the valve, the valve...
Ch. 12 - Many engines with WT have a phaser mounted to the...Ch. 12 - Multiple valve engines tend to be more efficient...Ch. 12 - Which of the following is not a type of valve...Ch. 12 - What type of valve lifter automatically...Ch. 12 - Prob. 8MCCh. 12 - While discussing the reasons for resurfacing a...Ch. 12 - While inspecting the timing gears of an engine:...Ch. 12 - Technician A says that positive valve stem seals...Ch. 12 - Prob. 4ASRQCh. 12 - Technician A says an engine may use one or more...Ch. 12 - Technician A says it is not necessary to measure...Ch. 12 - While discussing the Valvetronic system:...Ch. 12 - While checking a hydraulic phaser after the...Ch. 12 - While servicing a pair of aluminum cylinder heads:...Ch. 12 - While discussing camshafts Technician A says valve...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that positive valve stem seals fit tightly around the top of the valve guide. Technician B says that positive stem seals scrape oil off the valve as it moves up and down. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following statements is not true? Normally the desired valve face-to-seat contact area for intake valves is 1 inch. Normally the desired valve face-to-seat contact area for exhaust valves is 1 inch. The average valve seat width is 0.060 inch and the average seat begins 0.030 inch from the valve margin. A properly reconditioned seat has the correct seat width and sealing position on the valve face.arrow_forwardTechnician A says it is not necessary to measure valve stem height unless the valves have been replaced. Technician B says valve stem height can be adjusted with shims. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Valves are favored because of their lower cost and lighter weight Correct answer plug ball poppet butterflyarrow_forwardSelect the four seals commonly used to sealing around continuously reciprocating rods or pistons: piston rings lip seal U-cup face seals V-packing O-ringsarrow_forwardWhich of the following statements is not true? A direct acting PRV: Is complex in construction, therefore can malfunction if a very small dirt gets trapped inside the valve, which may result in safety hazard Offers uneven flow Does not provide precise pressure control Causes more wastage of HP compared to a compound one Which of the following basic system components has the primary function of removing the heat of compression from the air? Receiver Relief valve Pressure regulator Dryer Aftercooler Which of the following statements is true? A single acting cylinder may have two ports at two different ends and pressurized fluid can be directed to both of them A single acting cylinder with two ports will can be used as a double acting cylinder A single acting cylinder may have two ports at two different ends but into only one of the ports pressurized fluid is being directed A single acting cylinder…arrow_forward
- Choose correct answer: In direction control valve symbol with numbering system 2, 4,6&8 indicates exhaust ports. Select one: True Falsearrow_forwardwhat can happen when valve spring tension is too low?arrow_forwardTrue or False? Metering and proportioning valves balance the braking characteristics of disc and drum brakes.arrow_forward
- While discussing the results of an oil pressure test: Technician A says that when the fluid pressures are high, internal leaks, a clogged filter, low oil pump out put, or a faulty pressure regulator valve are indicated. Technician B says that if the fluid pressure increased at the wrong time, an internal leak at the servo or clutch seal is indicated. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A uses a 30-degree stone for topping a 45-degree valve seat. Technician B uses a 60-degree stone to lower a 45-degree valve seat. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardIndustrial Main What is the purpose of a check Valve?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Materials Science Mechanical Engineering - Part 3 Corrosion Explained; Author: Mega Mechatronics;https://www.youtube.com/watch?v=Il-abRhrzFY;License: Standard Youtube License