The different ways in which the Concrete Masonry Units are cured.

Question

Want to see more full solutions like this?

Answer 1

Question

Chapter 12, Problem 1RQ

To determine

The different ways in which the Concrete Masonry Units are cured.

Expert Solution & Answer

Answer to Problem 1RQ

The curing of Concrete Masonry Units can be done by low pressure kiln or by autoclaving.

Explanation of Solution

The curing of Concrete Masonry Units (CMUs) can be cured by low pressure steam kiln or an autoclaving.

In a low-pressure kiln, the units are placed on a set before the steam is introduced. This is done for one to three hours with a temperature of 22 ^oC to 38 ^oC. The steam produced is then induced which provides moisture to the units. The temperature is then gradually raised to 66 ^oC to 82 ^oC, depending on the composition of the concrete. This is maintained for a minimum duration of time until the required strength is achieved.

Autoclaving uses a high-pressure steam where the units are placed in the auto clave for a duration of two to five hours and then gradually steam is provided under a pressure of 150 psi for about three hours. Upon the attainment of maximum pressure and temperature, the units are soaked for 5 to 10 hours and the pressure is gradually released.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Students have asked these similar questions

How limestone or calcite affects the perfomance of concrete?

What are the benefits of adding admixtures such as water reducers and air-entraining agents to concrete?

Understand the many types of concrete admixtures and how they affect the concrete.

Answer 2

Question

Chapter 12, Problem 1RQ

To determine

The different ways in which the Concrete Masonry Units are cured.

Expert Solution & Answer

Answer to Problem 1RQ

The curing of Concrete Masonry Units can be done by low pressure kiln or by autoclaving.

Explanation of Solution

The curing of Concrete Masonry Units (CMUs) can be cured by low pressure steam kiln or an autoclaving.

In a low-pressure kiln, the units are placed on a set before the steam is introduced. This is done for one to three hours with a temperature of 22 ^oC to 38 ^oC. The steam produced is then induced which provides moisture to the units. The temperature is then gradually raised to 66 ^oC to 82 ^oC, depending on the composition of the concrete. This is maintained for a minimum duration of time until the required strength is achieved.

Autoclaving uses a high-pressure steam where the units are placed in the auto clave for a duration of two to five hours and then gradually steam is provided under a pressure of 150 psi for about three hours. Upon the attainment of maximum pressure and temperature, the units are soaked for 5 to 10 hours and the pressure is gradually released.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 3

Question

Chapter 12, Problem 1RQ

To determine

The different ways in which the Concrete Masonry Units are cured.

Expert Solution & Answer

Answer to Problem 1RQ

The curing of Concrete Masonry Units can be done by low pressure kiln or by autoclaving.

Explanation of Solution

The curing of Concrete Masonry Units (CMUs) can be cured by low pressure steam kiln or an autoclaving.

In a low-pressure kiln, the units are placed on a set before the steam is introduced. This is done for one to three hours with a temperature of 22 ^oC to 38 ^oC. The steam produced is then induced which provides moisture to the units. The temperature is then gradually raised to 66 ^oC to 82 ^oC, depending on the composition of the concrete. This is maintained for a minimum duration of time until the required strength is achieved.

Autoclaving uses a high-pressure steam where the units are placed in the auto clave for a duration of two to five hours and then gradually steam is provided under a pressure of 150 psi for about three hours. Upon the attainment of maximum pressure and temperature, the units are soaked for 5 to 10 hours and the pressure is gradually released.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 4

Question

Chapter 12, Problem 1RQ

To determine

The different ways in which the Concrete Masonry Units are cured.

Expert Solution & Answer

Answer to Problem 1RQ

The curing of Concrete Masonry Units can be done by low pressure kiln or by autoclaving.

Explanation of Solution

The curing of Concrete Masonry Units (CMUs) can be cured by low pressure steam kiln or an autoclaving.

In a low-pressure kiln, the units are placed on a set before the steam is introduced. This is done for one to three hours with a temperature of 22 ^oC to 38 ^oC. The steam produced is then induced which provides moisture to the units. The temperature is then gradually raised to 66 ^oC to 82 ^oC, depending on the composition of the concrete. This is maintained for a minimum duration of time until the required strength is achieved.

Autoclaving uses a high-pressure steam where the units are placed in the auto clave for a duration of two to five hours and then gradually steam is provided under a pressure of 150 psi for about three hours. Upon the attainment of maximum pressure and temperature, the units are soaked for 5 to 10 hours and the pressure is gradually released.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 5

Chapter 12, Problem 1RQ

To determine

The different ways in which the Concrete Masonry Units are cured.

Expert Solution & Answer

Answer to Problem 1RQ

The curing of Concrete Masonry Units can be done by low pressure kiln or by autoclaving.

Explanation of Solution

The curing of Concrete Masonry Units (CMUs) can be cured by low pressure steam kiln or an autoclaving.

In a low-pressure kiln, the units are placed on a set before the steam is introduced. This is done for one to three hours with a temperature of 22 ^oC to 38 ^oC. The steam produced is then induced which provides moisture to the units. The temperature is then gradually raised to 66 ^oC to 82 ^oC, depending on the composition of the concrete. This is maintained for a minimum duration of time until the required strength is achieved.

Autoclaving uses a high-pressure steam where the units are placed in the auto clave for a duration of two to five hours and then gradually steam is provided under a pressure of 150 psi for about three hours. Upon the attainment of maximum pressure and temperature, the units are soaked for 5 to 10 hours and the pressure is gradually released.

Answer 6

Chapter 12, Problem 1RQ

To determine

The different ways in which the Concrete Masonry Units are cured.

Expert Solution & Answer

Answer to Problem 1RQ

The curing of Concrete Masonry Units can be done by low pressure kiln or by autoclaving.

Explanation of Solution

The curing of Concrete Masonry Units (CMUs) can be cured by low pressure steam kiln or an autoclaving.

In a low-pressure kiln, the units are placed on a set before the steam is introduced. This is done for one to three hours with a temperature of 22 ^oC to 38 ^oC. The steam produced is then induced which provides moisture to the units. The temperature is then gradually raised to 66 ^oC to 82 ^oC, depending on the composition of the concrete. This is maintained for a minimum duration of time until the required strength is achieved.

Autoclaving uses a high-pressure steam where the units are placed in the auto clave for a duration of two to five hours and then gradually steam is provided under a pressure of 150 psi for about three hours. Upon the attainment of maximum pressure and temperature, the units are soaked for 5 to 10 hours and the pressure is gradually released.

Answer 7

Chapter 12, Problem 1RQ

To determine

The different ways in which the Concrete Masonry Units are cured.

Answer 8

Expert Solution & Answer

Answer to Problem 1RQ

The curing of Concrete Masonry Units can be done by low pressure kiln or by autoclaving.

Answer 9

Expert Solution & Answer

Answer 10

Expert Solution & Answer

Answer 11

Explanation of Solution

The curing of Concrete Masonry Units (CMUs) can be cured by low pressure steam kiln or an autoclaving.

In a low-pressure kiln, the units are placed on a set before the steam is introduced. This is done for one to three hours with a temperature of 22 ^oC to 38 ^oC. The steam produced is then induced which provides moisture to the units. The temperature is then gradually raised to 66 ^oC to 82 ^oC, depending on the composition of the concrete. This is maintained for a minimum duration of time until the required strength is achieved.

Autoclaving uses a high-pressure steam where the units are placed in the auto clave for a duration of two to five hours and then gradually steam is provided under a pressure of 150 psi for about three hours. Upon the attainment of maximum pressure and temperature, the units are soaked for 5 to 10 hours and the pressure is gradually released.

Answer 12

Ch. 12 - Prob. 1RQ Ch. 12 - Prob. 2RQ Ch. 12 - Prob. 3RQ Ch. 12 - Prob. 4RQ Ch. 12 - Prob. 5RQ Ch. 12 - Prob. 6RQ Ch. 12 - Prob. 7RQ Ch. 12 - Prob. 8RQ Ch. 12 - Prob. 9RQ

The different ways in which the Concrete Masonry Units are cured.

Concept explainers

The different ways in which the Concrete Masonry Units are cured.

Answer to Problem 1RQ

Explanation of Solution

Want to see more full solutions like this?

Chapter 12 Solutions