Principles of Foundation Engineering (MindTap Course List)
9th Edition
ISBN: 9781337705028
Author: Braja M. Das, Nagaratnam Sivakugan
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 12, Problem 12.28P
To determine
Find the allowable load for the pile using the modified EN formula.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A 10m long and 0.8m diameter precast concrete pile is driven into a saturated clay deposit
as shown in the figure below. The groundwater table is at the ground surface. For the ratio
of the undrained shear strength to vertical effective pressure is approximated as follows:
= 0.11 + 0.0037(PI)
NC
(9- 9
(OCR)8
OC
Determine the bearing capacity for the pile by the
a) Alpha (a) method.
b) Lambda (A) method
Depth, m
Layer 1
OCR = 5, Yat = 19.5 kN/m³, Pl = 35
Layer 2
OCR = 1.5, %at = 19.0 kN/m, Pl = 25
Layer 3
OCR = 8, %at = 19.5 kN/m, Pl = 20
10
D, = 0.8 m
D 10 m
A steel H-pile (section HP13 × 100) is driven by a hammer. The maximum rated
hammer energy is 40 kip-ft, the weight of the ram is 12 kip, and the length of
the pile is 90 ft. Also, we have coefficient of restitution
pile cap = 2.4 kip, hammer efficiency = 0.85, number of blows for the last inch
of penetration = 10, and E, = 30 × 10° lb/in.?. Estimate the pile capacity using
Eq. (9.114). Take FS = 6.
0.35, weight of the
%3D
A concrete bored pile has a diameter of 800 mm as given in the figure
below. Calculate the ultimate load carrying capacity of the pile.
-0.8-
Clay
Cu = 60 kN/m²
Y = 18 kN/m³
%3D
4m
G.W.T
Sand
6m
$ = 30°
Y = 20 kN/m³
Clay
Cu = 100 kN/m²
Y = 20 kN/m³
5m
Chapter 12 Solutions
Principles of Foundation Engineering (MindTap Course List)
Ch. 12 - Prob. 12.1PCh. 12 - A 20 m long concrete pile is shown in Figure...Ch. 12 - A 500 mm diameter are 20 m long concrete pile is...Ch. 12 - Redo Problem 12.3 using Coyle and Castellos...Ch. 12 - A 400 mm 400 mm square precast concrete pile of...Ch. 12 - Determine the maximum load that can be allowed on...Ch. 12 - A driven closed-ended pile, circular in cross...Ch. 12 - Consider a 500 mm diameter pile having a length of...Ch. 12 - Determine the maximum load that can be allowed on...Ch. 12 - Prob. 12.10P
Ch. 12 - Prob. 12.11PCh. 12 - Prob. 12.12PCh. 12 - A concrete pile 16 in. 16 in. in cross section is...Ch. 12 - Prob. 12.14PCh. 12 - Solve Problem 12.13 using Eqs. (12.59) and...Ch. 12 - Prob. 12.16PCh. 12 - Prob. 12.17PCh. 12 - A steel pile (H-section; HP 310 125; see Table...Ch. 12 - Prob. 12.19PCh. 12 - A 600 mm diameter and 25 m long driven concrete...Ch. 12 - Redo Problem 12.20 using Vesics method, assuming...Ch. 12 - Prob. 12.22PCh. 12 - Prob. 12.23PCh. 12 - Solve Problem 12.23 using the method of Broms....Ch. 12 - Prob. 12.25PCh. 12 - Solve Problem 12.25 using the modified EN formula....Ch. 12 - Solve Problem 12.25 using the modified Danish...Ch. 12 - Prob. 12.28PCh. 12 - Prob. 12.29PCh. 12 - Figure 12.49a shows a pile. Let L = 15 m, D (pile...Ch. 12 - Redo Problem 12.30 assuming that the water table...Ch. 12 - Refer to Figure 12.49b. Let L = 18 m, fill = 17...Ch. 12 - Estimate the group efficiency of a 4 6 pile...Ch. 12 - The plan of a group pile is shown in Figure...Ch. 12 - Prob. 12.35PCh. 12 - Figure P12.36 shows a 3 5 pile group consisting...Ch. 12 - Prob. 12.37P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- Concrete pile 356mm x 356mm Loose sand 1-30° 7-17.5kN/m 12 m Dense sand =42 0 y-18.5 kN/m A square concrete pile12m long is shown in Figure. Estimate the following: Ultimate shaft carrying capacity by Meyerhof's Method 471 kN 784.6 kN O 319.5kN 576.5 kN O 141.7 kNarrow_forwardA 450 mm x 450 mm concrete pile 20.0 m long is driven into sand deposits with y = 17 kN/m³ and = 30°. Find the ultimate load i.e. point load Qp by Meyerhoff's method and Janbu method. Meyerhoff's N = 55, Atmospheric pressure = 100 kN/m², Janbu's N = 18.4arrow_forward. A steel H-pile (section HP13 x100) is driven by a hammer. The maximum rated hammer energy is 40 kip-ft, the weight of the ram is 12 kip, and the length of the pile is 90 ft. Also, we have coefficient of restitution = 0.35, weight of the pile cap = 2.4 kip, hammer efficiency = 0.85, number of blows for the last inch of penetration = 12, and Ep = 330 x 106 Ib/in.2. Estimate the pile capacity using Eq. (9.114). Take FS = 5.arrow_forward
- P-2 A driven closed-ended pile, circular in cross section, is shown in the Figure. Calculate the following: Layer I Groundwater 3 m táble a. The ultimate point load using Meyerhof's procedure. 3 m Layer II b. The ultimate frictional resistance Qs. [Take K = 1.4 and ô'= 0.6º'] c. The allowable load of the pile (use FS = 3 15 m Layer II d. Calculate the (a), (b) and (c) if the layer III was a Clay soil with C,=80 kPa (use ca-method by Terzaghi and FS = 3) %3D Layer I Y = 15.7 kN/m³ 4' = 32° Layer II = 18.2 kN/m3 Ysat = 19.2 kN/m³ Layer III 381 mm Ysat 4' = 32° c' = 0 = 40° c' = 0 c' = 0arrow_forwardA 20 m long concrete pile is shown in Figure P12.2. Estimate the ultimate point load Qp by a. Meyerhofs method b. Vesics method c. Coyle and Castellos method Use m = 600 in Eq. (12.28).arrow_forwardA 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2arrow_forward
- P-1 A driven closed-ended pile, circular in cross section, is shown in the Figure. Calculate the following: Layer I Groundwater 3 m táble a. The ultimate point load using Meyerhof's procedure. 3 m Layer II b. The ultimate frictional resistance Qs. [Take K = 1.4 and ô'= 0.64'] c. The allowable load of the pile (use FS = 3 15 m Layer III d. Calculate the (a), (b) and (c) if the layer III was a Clay soil with C,=80 kPa (use a-method by Terzaghi and FS = 3) %3D Layer II = 18.2 kN/m3 Layer I Layer III Y = 15.7 kN/m³ o' = 32° c' = 0 19.2 kN/m3 381 mm Ysat 6' = 32° c' = 0 Ysat 4' = 40° c' = 0 Chabie Charrow_forwardFind the maximum pile capacity for the pile group shown in figure below. If My = 500 kN.m and V = 7200 kN. 'My X=1.4 - x=1.4- y=1.2 y=1.2arrow_forwardFor the (4 x 4) pile group as shown in the figure, the settlement of pile group, in a normally consolidated clay stratum having properties as shown in the figure will be (Load dispersion = 2 H:1 V) mm. 900 kN G Normally consolidated clay Yat = 20 kN/m 6 m w̟ = 40% 8 m w, = 25% e, = 1.05 Hard stratum 250 mm Piles are spaced at 0.5 m c/c. Diameter of piles is 250 mm 0.5 m 0.5 m Top viewarrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Fundamentals of Geotechnical Engineering (MindTap...Civil EngineeringISBN:9781305635180Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Fundamentals of Geotechnical Engineering (MindTap...
Civil Engineering
ISBN:9781305635180
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning