Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 11, Problem 10ASRQ
Technician A uses a feeler gauge and straightedge to determine the pump cover flatness. Technician B uses an outside micrometer to measure the diameter and thickness of the outer rotor. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Briefly describe the definition of hydraulic radius.
Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the vehicle. Technician B says their size is based on the top speed the vehicle can achieve. Who is correct?
a. A only b. B only c. both A and B d. neither A nor B
If a force of 150 pounds is applied to a master cylinder with a piston area of 1 square inch, how much force is developed on a wheel cylinder that has a piston area of 2 square inches?
a. 75 pounds b. 150 pounds c. 300 pounds d. 450 pounds
While manually bleeding a brake system, Technician A loosens all the brake bleeder screws at the same time. Technician B uses shop air to push the fluid and air through the lines and out the bleeder screws. Who is correct?
a. A only b. B only c. both A and B d. neither A nor B
Brake fluid serves as a lubricant for the parts of the hydraulic system and ensures smooth and even operation.
a. True b. False
Technician A says that a micrometer can be used tomeasure the outside diameter of something. TechnicianB says that a vernier caliper can be used to measurethe inside diameter of a bore. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor B
Chapter 11 Solutions
Automotive Technology
Ch. 11 - Describe how to inspect an oil pump.Ch. 11 - What is the cylinder taper?Ch. 11 - Describe how to measure main bearing oil...Ch. 11 - Where does maximum cylinder bore wear occur and...Ch. 11 - List three types of compression rings.Ch. 11 - What is the purpose of a thrust main bearing?Ch. 11 - How should the oil pump be primed when installing...Ch. 11 - Most pistons used today are made of. cast iron...Ch. 11 - Cam bearings in OHV engines are typically which...Ch. 11 - Which of the following is not of concern when...
Ch. 11 - Each halt' of a split bearing is made slightly...Ch. 11 - Prob. 5MCCh. 11 - Which of the following are not typically found in...Ch. 11 - All of the following are functions of the...Ch. 11 - Which type of oil ring is slotted so that excess...Ch. 11 - When removing the balance shaft assembly:...Ch. 11 - After installing cam bearings: Technician A checks...Ch. 11 - Technician A says that a cylinder wall with too...Ch. 11 - Technician A installs a cup-type core plug with...Ch. 11 - Technician A uses a micrometer to measure the...Ch. 11 - Technician A says that piston ring end gaps should...Ch. 11 - Technician A checks crankshaft oil clearance with...Ch. 11 - When removing the piston and rod assemblies from a...Ch. 11 - Technician A says that crankshaft counterweights...Ch. 11 - Technician A uses a feeler gauge and straightedge...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the vehicle. Technician B says their size is based on the top speed the vehicle can achieve. Who is correct? a. A only b. B only c. both A and B d. neither A nor B If a force of 150 pounds is applied to a master cylinder with a piston area of 1 square inch, how much force is developed on a wheel cylinder that has a piston area of 2 square inches? a. 75 pounds b. 150 pounds c. 300 pounds d. 450 pounds While manually bleeding a brake system, Technician A loosens all the brake bleeder screws at the same time. Technician B uses shop air to push the fluid and air through the lines and out the bleeder screws. Who is correct? a. A only b. B only c. both A and B d. neither A nor B Brake fluid serves as a lubricant for the parts of the hydraulic system and ensures smooth and even operation. a. True b. False Rusted-through brake lines are uncommon. a. True b. False A technician is diagnosing a vehicle with…arrow_forwardTechnician A uses a feeler gauge and straightedge to determine the pump cover flatness. Technician B uses an outside micrometer to measure the diameter and thickness of the outer rotor. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardCentralizer is to keep the casing away from the borehole so that there is some annular clearance on all sides. Which improves displacement efficiency and differential sticking. a. True b. Falsearrow_forward
- When fitting a freshly ground valve into a freshly ground seat: Technician A says that the seat should be ground more with the same stone if the margin is too small. Technician B says that the seat should be ground more with the same stone if the valve seat is too high. Who is correct?arrow_forwardThe indicator needle on a speedometer is heldto the zero position by ___.a. magnetic forceb. the weight of the needlec. the speedometer cabled. a hairspringarrow_forward4.a. You can usually check for a leak in a vacuum system by looking at or feelingA. at the vacuum gauge at the vacuum pump.B. for signs of dirt on the piping.C. at the exhaust of the vacuum pump. 4.b. When a pneumatic solenoid fails, the failure is normally due to aB. weak pilot.C. bad spool.D. ripped seal.arrow_forward
- Technician A says that the engine oil drain plug typically needs to be replaced with a new one at each oil change. Technician B says that engine oil drain plugs must be tightened with a torque wrench when they are installed. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardWhich among the valves is called non return valve a.flap check b.ball c.plunger valve d.diaphragm e.Checkarrow_forwardTechnician A uses a micrometer to measure the connectingrod journal for taper. Technician B uses amicrometer to measure the connecting rod journalfor out-of-roundness. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor Barrow_forward
- An instrument often used to check the alignment of twoshafts is theA. micrometer.B. dial indicator.C. manometer.D. sling psychrometer.arrow_forwardPressure regulators are being discussed. Technician A says they are located in the fuel rail. Technician B says they are located on the fuel rail. Who is correct? a. A only b. B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that coolant hoses should be squeezed to check for hardening or softening. Technician B says that coolant hoses should be visually inspected for swelling and cracks. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Principles of Lubrication | Automobile Engineering; Author: Magic Marks;https://www.youtube.com/watch?v=MGbbSxZTdCQ;License: Standard Youtube License