Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 10, Problem 2MC
To determine
The incorrect statement amongst the give statements.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
When checking the front end, which of the following are NOT cause for rejection?
Bearing cap is broken or missing or if there are any cracks or welded repairs to any components.
Front axle is bent or gear box mounting is loose, bolts are missing, or bolts or case are cracked.
All of the statements shown are cause for rejection.
The steering damper leaks, is loose, mount is cracked/ broken, or is missing or steering shaft coupler/universal is binding, frayed, or cracked.
Give at least 5 STATEMENT OF THE PROBLEM regarding to this
topic. (A statement of the problem is used in research work as a claim
that outlines the problem addressed by a study. The statement of the
problem briefly addresses the question: What is the problem that the
research will address?)
"Comparing ABS system to hydraulic break of a
vehicle"
What type of ball joint is used on the lower control arm of an SLA suspension when the coil spring is placed between the lower control arm and the frame, and the control arm is beneath the knuckle?
Chapter 10 Solutions
Automotive Technology
Ch. 10 - WHat should be worn when working with any type of...Ch. 10 - Why should a memory saver be installed before dis...Ch. 10 - Prob. 1TFCh. 10 - True or False? The first step in removing an...Ch. 10 - Prob. 3TFCh. 10 - What is the best way to lift a vehicle when...Ch. 10 - Prob. 2MCCh. 10 - The buildup of minerals and deposits inside the...Ch. 10 - Hydrocarbon solvents are. flammable toxic both a...Ch. 10 - Which cleaning method uses high-frequency sound...
Ch. 10 - Parts must be when they go into an abrasive blast...Ch. 10 - Prob. 7MCCh. 10 - Which of the following is not considered part of...Ch. 10 - Which of the following statements is not true...Ch. 10 - Which of the following is not a common way to...Ch. 10 - While working on an engine with an excessive...Ch. 10 - While discussing the common causes for cracks...Ch. 10 - Technician A uses a crane to remove an engine from...Ch. 10 - Prob. 4ASRQCh. 10 - While discussing abrasive cleaners: Technician A...Ch. 10 - Technician A labels or marks all electrical wires...Ch. 10 - While discussing cleaning engine parts: Technician...Ch. 10 - While loosening the axle shaft hub nuts on a FWD...Ch. 10 - While preparing to remove an engine: Technician A...Ch. 10 - After removing the vehicles hood in preparation...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following is part of the sprung weight of a vehicle? a. Steering linkage b. Tires c. Engine d. All of the abovearrow_forwardTechnician A says that the use of firmer, urethane bushings in the suspension improves the vehicles road-holding ability and handling. Technician B says that firmer bushings help eliminate torque steer in some FWD vehicles. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that the suspension switch must be turned off before raising any corner of a car with an electronic air suspension. Technician B says that the ignition switch must not be turned on while any corner of a car with electronic air suspension is raised. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Name the three main driveline components that are added to a RWD vehicle to make it a 4WD vehicle.arrow_forwardTechnician A says that a seized shift linkage may cause the transfer case to operate only in 4WD. Technician B says that a worn and loose linkage may cause a transfer case to operate only in 2WD. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that the front wheel bearings on a typical FWD car are pressed in and out of the steering knuckle assembly. Technician B says that the front wheel bearings on a typical FWD may be bolted into the steering knuckle. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- What may be caused by improper engine and transmission mounts on FWD vehicles?arrow_forwardTechnician A says that each ABS has its own diagnostic procedure involving use of the brake and antilock warning lamps, special testers, breakout boxes, scan tools, troubleshooting charts, and wiring diagrams. Technician B says that ABSs vary in the number of codes they can store and whether they will retain the code in memory when the ignition is turned off. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardThe modified MacPherson rear strut suspension is common in _______. a. FWD vehicles b. RWD vehicles c. pickup trucks d. station wagonsarrow_forward
- Which of the following statements about unibodyconstruction is not true?a. A unibody is a stressed hull structure in whicheach of the body parts supplies structural supportand strength to the entire vehicle.b. Unibody vehicles tend to be tightly constructedbecause the major parts are all welded together.c. All unibodies are constructed from steel.d. Most front-wheel-drive unibody vehicles have acradle or partial frame.arrow_forwardA multilink front suspension contains which of the following? a. Strut b. Control arms c. Ball joints d. All of the abovearrow_forwardWhile conducting a bounce test: Technician A says that the bumper should be pushed two or three times downward with considerable weight applied on each corner of the vehicle. Technician B says that one free upward bounce should stop the vertical chassis movement if the shock absorber or strut provides proper spring control. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,