Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 10, Problem 2ASRQ
While discussing the common causes for cracks developing in a cylinder block or head: Technician A says that the chilling of a hot engine by a sudden rush of cold water or air over the surf ace may cause cracking. Technician B says that excessive overheating is a common cause. Who is correct?
- Technician A
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A vehicle has had several radiator
replacements, and each time there has been
pinhole leaks in the aluminum. Technician A
states that the engine coolant may need to be
exchanged more often. Technician B states
that the engine grounds should be inspected
closely since this could be the cause. Who is
correct?
Select one:
a. Technician A only
b. Technician B only
c. Both Technicians A and B
d. Neither Technician A nor B
Why is it important to loosen the cylinder head bolts in the recommended order?
The CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the right side of the vehicle appear to be stretched apart.
Technician A says that one or more of the engine/transaxle's mounts may be broken.
Technician B says that one or more of the engine/transaxle's subframe mounts may be broken.
Who is correct?
O a. A only
O b.B only
C. Both A and B
O d. Neither A nor B
Chapter 10 Solutions
Automotive Technology
Ch. 10 - WHat should be worn when working with any type of...Ch. 10 - Why should a memory saver be installed before dis...Ch. 10 - Prob. 1TFCh. 10 - True or False? The first step in removing an...Ch. 10 - Prob. 3TFCh. 10 - What is the best way to lift a vehicle when...Ch. 10 - Prob. 2MCCh. 10 - The buildup of minerals and deposits inside the...Ch. 10 - Hydrocarbon solvents are. flammable toxic both a...Ch. 10 - Which cleaning method uses high-frequency sound...
Ch. 10 - Parts must be when they go into an abrasive blast...Ch. 10 - Prob. 7MCCh. 10 - Which of the following is not considered part of...Ch. 10 - Which of the following statements is not true...Ch. 10 - Which of the following is not a common way to...Ch. 10 - While working on an engine with an excessive...Ch. 10 - While discussing the common causes for cracks...Ch. 10 - Technician A uses a crane to remove an engine from...Ch. 10 - Prob. 4ASRQCh. 10 - While discussing abrasive cleaners: Technician A...Ch. 10 - Technician A labels or marks all electrical wires...Ch. 10 - While discussing cleaning engine parts: Technician...Ch. 10 - While loosening the axle shaft hub nuts on a FWD...Ch. 10 - While preparing to remove an engine: Technician A...Ch. 10 - After removing the vehicles hood in preparation...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While determining the cause for air leaking out of the oil throttle body during a cylinder leakage test: Technician A says that a burnt intake valve is indicated. Technician B says that a warped cylinder head or bad head gasket is indicated. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forwardWhile diagnosing the cause for an engine having good results from a compression test and cylinder leakage test but poor results from a cylinder power balance test: Technician A says that incorrect valve timing is the most likely cause. Technician B says that a severely worn cam lobe is a likely cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says that if an engine had good results from a compression test, it will have good results from a cylinder leakage test Technician B says that if an engine had good results from a cylinder leakage test, it will have good results from a running compression test Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- While discussing the reasons for resurfacing a cylinder head; Technician A says it should be resurfaced to make it flat and very smooth so the head gasket can seal properly during engine assembly. Technician B says that it can be resurfaced to raise the compression. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile determining the most likely problem of an engine with poor compression test results but acceptable cylinder leakage readings: Technician A says that the problem may be incorrect valve timing. Technician B says that the problem is worn valve seats. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing the causes of extreme engine bearing damage Technician A says that contaminated and old engine oil could be the cause. Technician B says that a leaking radiator could be the cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Which of the following statements is incorrect? Cylinder head bolts must be tightened to the proper amount of torque. Most cylinder head bolts are tightened in a sequence that starts on one end. On some engines, the head bolts are retorqued after the engine has been run and is hot. Many engines use head bolts of different lengths.arrow_forwardWhile looking at the results of an oil pressure test: Technician A says that higher than normal readings can be caused by using oil that is too thin. Technician B says that higher than normal readings can be expected on a cold engine. Who is correct? Technician A Technician Both A and B Neither A nor Barrow_forwardWhich of the following statements about the purpose of a cylinder head gasket is not true? It seals intake stroke vacuum, combustion pressure, and the heat of combustion. It prevents coolant leakage and resists rust, corrosion and, in many cases, meters coolant flow. It allows for lateral and vertical head movement as the engine heats and cools. It meters lubricating oil onto the engines cylinder walls.arrow_forward
- Which of the following is not a common way to identify the location of cracks in the engine block or cylinder head? Pressure checks Vacuum test Magnetic particle inspection Penetrativearrow_forwardTechnician A says an engine may use one or more valve springs per valve. Technician B says additional valve springs are used to control vibration and increase total pressure. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardCarbon deposits on the intake valve or seat may cause the valve not to close properly. Tech a says that the flywheel will be harder to spin when starting the engine. Tech b says that the engine will loose power. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Material Properties 101; Author: Real Engineering;https://www.youtube.com/watch?v=BHZALtqAjeM;License: Standard YouTube License, CC-BY