Materials for Civil and Construction Engineers (4th Edition)
4th Edition
ISBN: 9780134320533
Author: Michael S. Mamlouk, John P. Zaniewski
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 10, Problem 10.21QP
a)
To determine
Draw the graph between load and deflection using spread sheet.
b)
To determine
Plot the proportional limit on the graph.
c)
To determine
The modulus of rupture of the wood lumber.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A wood specimen was subjected to bending until failure by applying a load inthe middle of its span. The specimen has a cross section of 25 mm * 25 mm(actual dimensions) and a span of 350 mm between the simple supports. Theload and the deflection in the middle of the span were recorded as shown inTable P10.22.a. Using a computer spreadsheet program, plot the load–deflectionrelationship.b. Plot the proportional limit on the graph.c. Calculate the modulus of rupture (flexure strength).
A wood specimen having a square cross section of 2-inch x 2-inch (actual dimensions) was tested in bending by applying a load at the middle of the span, where the span between the simple supports was 28 inches. The deflection under the load was measured (see below). Plot the load versus deflection relationship. Identify the proportional limit on the diagram. Calculate the modulus of rupture. Does the modulus of rupture truly represent the extreme fiber stresses in the specimen? Comment on the assumptions used to compute the modulus of rupture and the actual response of the wood specimen
A wood specimen was subjected to bending until failure by applying a loadin the middle of its span. The specimen has a cross section of 1 in. * 1 in.(actual dimensions) and a span of 14 in. between the simple supports. Theload and the deflection in the middle of the span were recorded as shown inTable P10.22.a. Using a computer spreadsheet program, plot the load–deflectionrelationship.b. Plot the proportional limit on the graph.c. Calculate the modulus of rupture (flexure strength).
Chapter 10 Solutions
Materials for Civil and Construction Engineers (4th Edition)
Ch. 10 - What are the two main classes of wood? What is the...Ch. 10 - Prob. 10.2QPCh. 10 - Prob. 10.3QPCh. 10 - Discuss the anisotropic nature of wood. How does...Ch. 10 - Prob. 10.5QPCh. 10 - Prob. 10.6QPCh. 10 - Prob. 10.7QPCh. 10 - Prob. 10.8QPCh. 10 - Prob. 10.9QPCh. 10 - Prob. 10.10QP
Ch. 10 - Prob. 10.11QPCh. 10 - Prob. 10.12QPCh. 10 - Prob. 10.13QPCh. 10 - Prob. 10.14QPCh. 10 - Prob. 10.15QPCh. 10 - Prob. 10.16QPCh. 10 - Prob. 10.17QPCh. 10 - Prob. 10.18QPCh. 10 - Prob. 10.19QPCh. 10 - Prob. 10.20QPCh. 10 - Prob. 10.21QPCh. 10 - Prob. 10.22QPCh. 10 - Prob. 10.23QPCh. 10 - A wood specimen was prepared with actual...Ch. 10 - A pine wood specimen was prepared with actual...Ch. 10 - Prob. 10.26QPCh. 10 - Prob. 10.27QPCh. 10 - Prob. 10.28QPCh. 10 - Prob. 10.29QPCh. 10 - Prob. 10.30QPCh. 10 - Prob. 10.31QPCh. 10 - Prob. 10.32QPCh. 10 - Prob. 10.33QP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A pine wood specimen was prepared with actual dimensions of 50 mmx50 mm x 250 mm and grain parallel to its length. The deformation was measured over a gauge length of 200 mm. The specimen was subjected to compression parallel to the grain failure. The load- deformation results are shown in table below: Load (kN) Deformation (mm) 8.9 0.457 17.8 0.597 26.7 0.724 34.5 0.838 43 0.965 52.9 1.118 62.01 1.27 71.03 1.422 80.1 1.588 89 1.765 99.6 1.956 108 2.159 111.3 2.311 112 2.456 a. Using a computer spreadsheet program, plot the stress-strain relationship. b. Calculate the modulus of elasticity. С. What is the failure stress?arrow_forwardA wood specimen was prepared with actual dimensions of 25 mm * 25 mm *150 mm and grain parallel to its length. Displacement was measured over a100 mm gauge length. The specimen was subjected to compression parallel to the grain to failure. The load–deformation results are as shown in Table P10.24. a. Using a computer spreadsheet program, plot the stress–strain relationship.b. Calculate the modulus of elasticity.c. What is the failure stress?arrow_forwardThe grains of wood in the board make an angle of 20° with the horizontal as shown. The board is subjected to an axial load of P = 300 N. (Figure 1) Part A Determine the normal stress that acts perpendicular to the grains. Express your answer to three significant figures and include the appropriate units. µA Value Units Submit Request Answer Figure < 1 of 1 Part B Determine the shear stress that acts parallel to the grains. Express your answer to three significant figures and include the appropriate units. HA -300 mm 160 mm Ta'y = Value Units 20° 25 mm1 Submit Request Answerarrow_forward
- The grains of wood in the board make an angle of 20° with the horizontal as shown. The board is subjected to an axial load of P = 250 N . (Figure 1) Part A Determine the normal stress that acts perpendicular to the grains. Express your answer to three significant figures and include the appropriate units. µA Value Units Figure 1 of 1 Submit Request Answer Part B 300 mm Determine the shear stress that acts parallel to the grains. 60 mm Express your answer to three significant figures and include the appropriate units. 20° 25 mm HẢ ? Value Units P Pearsonarrow_forwardA wood beam reinforced by an aluminum channel section is shown in the figure. 150 mm 230 mm 38 mm 6.5 mm -163 mm- The beam has a cross section of dimensions 150 mm x 230 mm, and the channel has a uniform thickness of 6.5 mm. If the allowable stresses in the wood and aluminum are 8 MPa and 50 MPa, respectively, and if their moduli of elasticity are in the ratio 1 to 6, what is the maximum allowable bending moment for the beam? Enter the magnitude in kN · m. (Assume that the component parts of the beam are securely bonded by adhesives or connected by fasteners. Also, be sure to use the transformed-section method in the solution.) (No Response) 14.06 kN· marrow_forwardThe device shown is used for determining the shear strength of the wood. The dimensions of the woodblock are 6 in x 8 in x 1.5 in. If the force required to break the wood block is 12 kips, determine theaverage shear strength of the wood.arrow_forward
- Calculate the modulus of elasticity of the wood specimen with the stress-strain relationship shown in figure below. 25 20 15 10 0.1 0.2 0.3 0.4 0.5 STRAIN (%) COMPRESSIVE STRESS PARALLEL TO GRAINS (MPA)arrow_forwardQ: A composite section shown in Figure consisted of a rectangular and triangular sections with a semicirele hole as shown. Locate the centroid (x, y) of this section using the below table. Y 90 mm 10 mm 20 mm 10 mm 60 mm Xị Yi Part Area Ai (mm) (mm) (mm) A, Xi (mm') A, Yi (mm') +Yellow rectangle + Blue triangle - White semicircle Totalsarrow_forwardThe wood has an allowable normal stress of Oallow = 15 MPa and an allowable shear stress of Tallow = 1.33 MPa. (Figure 1) Part A Determine the minimum dimension h of the beam's cross section to safely support the load. Express your answer to three significant figures and include the appropriate units. µA ? h = Value Units Submit Request Answer Figure Provide Feedback 25 kN/m B 2 m 100 mmarrow_forward
- A wood beam reinforced by an aluminum channel section is shown in the figure. 150 mm 232 mm 38 mm 6.5 mm 163 mm- The beam has a cross section of dimensions 150 mm x 232 mm, and the channel has a uniform thickness of 6.5 mm. If the allowable stresses in the wood and aluminum are 8 MPa and 46 MPa, respectively, and if their moduli of elasticity are in the ratio 1 to 6, what is the maximum allowable bending moment for the beam? Enter the magnitude in kN • m. (Assume that the component parts of the beam are securely bonded by adhesives or connected by fasteners. Also, be sure to use the transformed-section method in the solution.) kN marrow_forwardThe rectangular wood beam is loaded as shown in the figure. 12 kN. 8 KN/m 150 m 250 mm 10m 2 m What is the bending stress in the beam 2 meters from point A? 7.68 MPa O 5.76 MPa O 10.24 MPa 4.48 MPa What is the bending stress 50 mm from the top of the beam 0.5 meters from point A? * 3.456 MPa 5.760 MPa 10.245 MPa 6.144 MPa What is the shear stress in the beam at point C? O0.48 MPa 0.80 MPa 0.64 MPa O0.32 MPaarrow_forwardThe figure shows a glued joint, known as a finger joint, in a 200 mm. by 25 mm piece of lumber. Find the normal and shear stresses acting on the surface of the joint.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Structural Analysis (10th Edition)Civil EngineeringISBN:9780134610672Author:Russell C. HibbelerPublisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Fundamentals of Structural AnalysisCivil EngineeringISBN:9780073398006Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel LanningPublisher:McGraw-Hill Education
Traffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning
Structural Analysis (10th Edition)
Civil Engineering
ISBN:9780134610672
Author:Russell C. Hibbeler
Publisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Fundamentals of Structural Analysis
Civil Engineering
ISBN:9780073398006
Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning
Publisher:McGraw-Hill Education
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning