Pearson eText for Materials for Civil and Construction Engineers -- Instant Access (Pearson+)
4th Edition
ISBN: 9780137505586
Author: Michael Mamlouk, John Zaniewski
Publisher: PEARSON+
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 1, Problem 1.51QP
Referring to the dial gauge shown in Figure P1.51, determine
a.    Accuracy
b.    Sensitivity
c.    Range, given that the small pointer moves one division for each full turn of the large pointer
d.    Which of the preceding items can be improved through calibration?
e.    For measuring devices, which of the following two statements is always true?
(i)Â Â Â Â Accuracy cannot exceed sensitivity
(ii)Â Â Â Â Sensitivity cannot exceed accuracy
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Referring to the dial gauge shown in Figure P1.44, determine
a. Accuracy
b. Sensitivity
c. Range, given that the small pointer moves one division for each full turn
of the large pointer
d. Which of the preceding items can be improved through calibration?
e. For measuring devices, which of the following two statements is always
true?
19 0
18
17
Bai
16
15
-14
13
002 mm
12
11 10
FIGURE P1.44
(i) Accuracy cannot exceed sensitivity
(ii) Sensitivity cannot exceed accuracy
6.
During the design of a building the deflection of a beam is calculated to be 0.90 inch. In order to limit the maximum deflection of the beam to 0.75 inch, how should the design be changed?
A. Substitute a beam having a plastic modulus 20 percent greater
B. Substitute a beam having a moment of inertia 20 percent greater
C. Substitute a beam having a moment of inertia 15 percent greater
D. Substitute a beam having a yield point 20 percent greater
1 - An aluminum plate is subjected to uniform stress along its
boundaries, as shown in the figure. Determine the change of length
of diagonal BD.
120mm
120 MPa
160mm
C
B
V
100MPa
-200 MPa
E-80GPa
âś“=0.3
G=30MPa
Chapter 1 Solutions
Pearson eText for Materials for Civil and Construction Engineers -- Instant Access (Pearson+)
Ch. 1 - State three examples of a static load application...Ch. 1 - A material has the stressstrain behavior shown in...Ch. 1 - A tensile load of 50.000 lb is applied to a metal...Ch. 1 - A tensile load of 190 kN is applied to a round...Ch. 1 - A cylinder with a 6.0 in. diameter and 12.0 in....Ch. 1 - A metal rod with 0.5 inch diameter is subjected to...Ch. 1 - A rectangular block of aluminum 30 mm 60 mm 90...Ch. 1 - A plastic cube with a 4 in. 4 in. 4 in. is...Ch. 1 - A material has a stressstrain relationship that...Ch. 1 - On a graph, show the stressstrain relationship...
Ch. 1 - The rectangular block shown in Figure P1.11 is...Ch. 1 - The rectangular metal block shown in Figure P1.11...Ch. 1 - A cylindrical rod with a length of 380 mm and a...Ch. 1 - A cylindrical rod with a radius of 0.3 in. and a...Ch. 1 - A cylindrical rod with a diameter of 15.24 mm and...Ch. 1 - The stressstrain relationship shown in Figure...Ch. 1 - A tension test performed on a metal specimen to...Ch. 1 - An alloy has a yield strength of 41 ksi, a tensile...Ch. 1 - Prob. 1.21QPCh. 1 - Figure P1.22 shows (i) elasticperfectly plastic...Ch. 1 - An elastoplastic material with strain hardening...Ch. 1 - A brace alloy rod having a cross sectional area of...Ch. 1 - A brass alloy rod having a cross sectional area of...Ch. 1 - A copper rod with a diameter of 19 mm, modulus of...Ch. 1 - A copper rod with a diameter of 0.5 in., modulus...Ch. 1 - Define the following material behavior and provide...Ch. 1 - An asphalt concrete cylindrical specimen with a...Ch. 1 - What are the differences between modulus of...Ch. 1 - Prob. 1.33QPCh. 1 - A metal rod having a diameter of 10 mm is...Ch. 1 - What is the factor of safety? On what basis is its...Ch. 1 - Prob. 1.36QPCh. 1 - Prob. 1.37QPCh. 1 - A steel rod, which is free to move, has a length...Ch. 1 - In Problem 1.38, if the rod is snugly fitted...Ch. 1 - A 4-m-long steel plate with a rectangular cross...Ch. 1 - Estimate the tensile strength required to prevent...Ch. 1 - Prob. 1.42QPCh. 1 - Briefly discuss the variability of construction...Ch. 1 - In order to evaluate the properties of a material,...Ch. 1 - A contractor claims that the mean compressive...Ch. 1 - A contractor claims that the mean compressive...Ch. 1 - Prob. 1.47QPCh. 1 - Prob. 1.48QPCh. 1 - Prob. 1.49QPCh. 1 - Briefly discuss the concept behind each of the...Ch. 1 - Referring to the dial gauge shown in Figure P1.51,...Ch. 1 - Repeat Problem 1.51 using the dial gauge shown in...Ch. 1 - Measurements should be reported to the nearest...Ch. 1 - During calibration of an LVDT, the data shown in...Ch. 1 - During calibration of an LVDT, the data shown in...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- The (G-E) diagram obtained in the tensile test performed on a metal sample with a diameter of 16 mm is as follows. The loads at points A, B and C and the elongation measured on l. 16 cm gauge length were determined as follows: B A B C Load (kgf) 4800 8400 7200 Elongation (mm) 0.192 28.8 38.4 a) Calculate the proportionality limit, modulus of elasticity, tensile strength, maximum uniform elongation, and contraction-elongation ratio of the metal. b) Since the measured diameter of the metal at break is 12 mm, find the constriction ratio and the actual stress at break.arrow_forwardAt a temperature of 37.4 °C a 0.49-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 128.7°C, determine the change in length of the steel rod if L = 328.25 mm and M = 215 mm. Round off the final answer to four decimal places.arrow_forwardCalculate the value of b in millimeters. USE NSCP 2015.arrow_forward
- Please solve for Ray, Rax, Rdy, Rdx, and AB. Please show the steps don't skip any step as That is really what i need to understand this problem. Thank you  PROVIDE HANDWRITTEN ANSWERarrow_forwardThe assembly shown in the figure consists of an aluminum tube AB and a steel rod BC. The rod is attached to the tube through the rigid collar at B and passes through the tube. The cross-sectional area of the rod is 75 mm2 and the cross-sectional area of the tube is 400 + UV in mm2, where UV is 99. A tensile load of 80 kN is applied to the rod. Take Est = 200 GPa for the steel rod, Eal = 70 GPa for the aluminum tube. Determine: (a) the displacement of end C with respect to end B (i.e., the elongation of the steel rod), (b) the displacement of end B with respect to the fixed end A (i.e., the shrink of the aluminum tube), (c) the displacement of the end C of the rod (i.e., (a) + (b)).arrow_forwardThe stress-strain relation shown in figure below was obtained during the tensile test of an aluminum alloy specimen. Picture1(3).jpg 60,000 40,000 20,000 0.002 0.004 0.006 0.008 Strain, in./in. Copyright ©2017 Pearson Education, All Rights Reserved Determine tangent modulus at a stress of 45,000 psi in same unit (psi). Stress, psiarrow_forward
- Measurements should be reported to the nearest 1000, 100, 10, 1, 0.1, 0.01, 0.001 units, etc., depending on their variability and intended use. Using your best judgment, how should the following measurements be reported? Deformation of a steel specimen during the tension test (in.) Tensile strength of steel (psi) Modulus of elasticity of aluminum (MPa) Weight of aggregate in a sieve analysis test (grams) Compressive strength of portland cement concrete (psi) Moisture content in a concrete masonry unit (percent) Asphalt content in hot-mix asphalt (percent) Specific gravity of wood Distance between New York City and Los Angeles (miles) Dimensions of a computer microchip (mm)arrow_forwardQuestion 3: The block shown is made of a magnesium alloy for which E=760GPa and 9 =0.35. Knowing that o=157 MPa, determine (a) the magnitude of o, for which the change in the height of the block will be zero, (b) the corresponding change in the area of the face ABCD, (c) the corresponding change in the volume of the block.arrow_forwardA piece of Titanium originally at 300 mm long is pulled in tension with a stress load of 40,000 psiWhat is the elongation if the deformation is elasticRefer to the given table for other needed data. Do not answer in image format. Maintain accuracy and quality in your answer. Answer completely.arrow_forward
- Q2/Show the mechanical properties changes during tensile test of a metal specimen. Write the mathematical relationships. 443Xarrow_forwardAnswer the following questions based on the given information in the table and further calculation (if needed for any missing parameter, e.g. strain at yield point). Assume all metals started with the same shape and size before the tensile tests occurred. Material A B C D E Yield Strength (MPa) 105 600 430 355 The material that experienced the greatest percent reduction in area is material The hardest material is material The hardest material has Tensile Strength (MPa) The material that experienced the greatest percent reduction in area has 135 850 The material that experienced the largest change in shape before plastic deformation occurred is material The stiffest material is material The stiffest material has 535 365 Fracture before yielding The material that experienced the largest change in shape before plastic deformation occurred has Strain at Fracture [Choose ] [Choose ] [Choose ] [Choose ] [Choose ] [Choose ] [Choose ] [Choose ] 0.45 0.15 0.20 0.25 Fracture Strength (MPa)…arrow_forwardA 10 cm long rectangular bar (when subjected to a tensile load) deforms by 0.1 mm. Calculate the normal strain.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Engineering Fundamentals: An Introduction to Engi...Civil EngineeringISBN:9781305084766Author:Saeed MoaveniPublisher:Cengage LearningMaterials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Engineering Fundamentals: An Introduction to Engi...
Civil Engineering
ISBN:9781305084766
Author:Saeed Moaveni
Publisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning
Experimental Testing of a Real Scale Flat Slab Building for Gravity and Lateral Loading; Author: American Concrete Institute;https://www.youtube.com/watch?v=t3jybLy7ev8;License: Standard Youtube License