You are given the data shown on the sketech of a load test. 1- Find the ultimate bearing capacity by Meyerhof equations 2- Find the ultimate bearing capacity by Hansen equations 3- Find the allowable bearing capacity by Terzaghi equations without considering the lateral forece and saftey factor of 2.4. H- 450 kN 1.5 0 kN Vul -1350 kN H- 0 kN 0.75 m y =16.4 kN/m • -25°,c = 35 kPa Gs = 2.65, e = 0.71 1.25 m L-3 m GWT

You are given the data shown on the sketech of a load test. 1- Find the ultimate bearing capacity by Meyerhof equations 2- Find the ultimate bearing capacity by Hansen equations 3- Find the allowable bearing capacity by Terzaghi equations without considering the lateral forece and saftey factor of 2.4. H- 450 kN 1.5 0 kN Vul -1350 kN H- 0 kN 0.75 m y =16.4 kN/m • -25°,c = 35 kPa Gs = 2.65, e = 0.71 1.25 m L-3 m GWT

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q4) A 400 square column carries dead load of 1050 kN and imposed load of 300 kN as shown in figure Q4. The safe bearing capacity of soil is 170 kN/m². By using following design data: Design data: The characteristic strength of reinforcement steel (f) = 500 N/mm? The characteristic strength of concrete is (feu) = 35 N/mm?. Over all depth of foundation 600 mm Diameter of tension reinforcement is 20 mm, Density of concrete is 24 kN/m3 Concrete cover 50 mm Design size of square footing Design of bending reinforcement iii. Check punching shear, face shear, i. ii. footing against = 1050 kN imposed = 300 kN Axial loads: dead Figure Q4
We are interested in the forces at a footing due to dead, live, and earthquake loads. The horizontal forces are 0.6 for dead, 0.9 for live, and 4.9 for earthquake. The vertical forces are 2.5 for dead, 3.7 for live, and 3.8 for earthquake. For vertical forces, positive indicates compression and negative indicates uplift. Apply all the relevant load combinations. All forces are in kips. Determine the largest compressive vertical force in kips to two decimals.
Work meyehof its own equation and hansens its own equation don't mixed pls . And tarzags and allowable
no. 3 please with explanation
1. PLEASE I NEED IT ASAP.
Give me right answer with short explanation. Note: If you don't know the answer please leave it but don't give me wrong answer. When revising the characteristic value of the subgrade bearing capacity, which of the following statements is correct ( ) (multiple choices)A. If the width of the foundation is less than 3m, it shall be taken as 3m; if it is greater than 6m, it shall be taken as 6m. B. If the filling is carried out after the superstructure construction, the buried depth shall be calculated from the filling surface. C. The characteristic value of subgrade bearing capacity determined by deep load test does not need depth correction. D. For the basement, if box foundation is adopted, the buried depth shall be calculated from the indoor ground.
The pin support A and roller support B of the bridge truss are supported on the concrete abutments. If the square bearing plates at C and D are 20 inches x 20 inches, and the bearing failure for concrete is (?????)? =3.8 ???, determine the factor of safety against bearing failure for the concrete under each plate.
In the following beam with the working section shown is subjected to the indicated loads and supported as shown, determine the magnitude of the twist BA and the deflection YC in the middle. Consider E = 70 GPa, A = 7.5 x 10-3 m2, IZ = 61.3 x 10-6 m4, IY = 23.2 x 10-6 m4 Develop by: 1) Double integration method 10 kN 2) Overlay Method 3) Moment area method 4m 4 m develop: a) Problem approach and solution sequence b) Free body diagram c) Calculation of intermediate and constant forces d) Bending moment diagram e) Application of equations and associated tables Caniatidado AM 141do earde tier ade
4.ASAP