Two angle bars B and C are riveted to bracket A. Knowing that both angle bars are compression and that force is 25 kN in angle bar B and 40 kN in angle bar C, determine following: a. Number of 19 mm diameter rivets in angle bar B if the allowable bearing stress of angle is 60 MPa. Thickness of angle bar B is 6 mm. b. Number of 19 mm diameter rivets in angle bar C if the allowable shearing stress of rivet 25 MPa. Thickness of angle bar is 5 mm. 45° 20°. A O-O-O-O--.

Two angle bars B and C are riveted to bracket A. Knowing that both angle bars are compression and that force is 25 kN in angle bar B and 40 kN in angle bar C, determine following: a. Number of 19 mm diameter rivets in angle bar B if the allowable bearing stress of angle is 60 MPa. Thickness of angle bar B is 6 mm. b. Number of 19 mm diameter rivets in angle bar C if the allowable shearing stress of rivet 25 MPa. Thickness of angle bar is 5 mm. 45° 20°. A O-O-O-O--.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the below wooden beam, under the given loading and dimensions: ŢŢ 50 kN C 4m w = 10 kN/m B 150 mmm Calculate ans sketch the shear stress distribution of the section at the support 360 mmm
no. 3 please with explanation
Point B of the system given below is movable support and Enpoint is fixed bearing. According to the given loading condition a) Draw the normal force, moment and shear force diagrams. B) Check whether the section used between AB-BC-CD is suitable, as the material has normal allowable stress em = 85 Mpa and shear strength em = 50 Mpa. c) Find the diameter d of the section used between DE-EF since the normal allowable stress of the material is em = 85 Mpa and the shear strength is em = 50 Mpa.
i need the answer quickly
The assembly consists of three disks A, B and C that are used to support the load of 140 kN. Determine the smallest diameter d, of the top disk, the diameter d₂ within the support space, and the diameter d of the hole in the bottom disk. The allowable bearing stress for the material is (allow)b = 350 MPa and allowable shear stress is allow=125 MPa. B A 140 KN - dz d₂ 20 mm 10 mm
LAlogo_badge The allowable shear stress is Tallow = 9 ksi. (Figure 1) Figure Part A V 1 in. vec Submit VO VD ΑΣΦΙΚΗ 1 in. 3 in. Determine the largest shear force V that the member can sustain. Express your answer in kilopounds to three significant figures. Request Answer 1 in. 3 in. S < 1 of 1 C ? ( kip
2. The lap joint is fastened with four 30-mm-diameter rivets. The working stresses are 84 MPa for the rivets in shear and 84 MPa for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets... 35 mm KATIN 160 mm
Please write All answer in mpa
Six 7/8-in-diameter rivets fasten the plate in Figure below to the fixed member. Determine the average shearing stress caused in each rivet by the 15 kips loads. What additional loads P can be applied before the shearing stress in any rivet exceeds 9100 psi?
DETERMINE THE CONCRETE AND STEEL STRESS AT THE FIXED SUPPORT C.
R1-5. Determine the average punching shear stress the circular shaft creates in the metal plate through section AC and BD. Also, what is the average bearing stress developed on the surface of the plate under the shaft? C 40 KN -50 mm- -60 mm- -120 mm B D $10 mm
Two horizontal 5.39-kip forces are applied to pin B of the assembly shown. Knowing that a pin of 1.01-in. diameter is used at each connection,determine the bearing stress (in psi) at Bin member AB.