A beam simply supported on a 8 m span carries a uniformly distributed load of 30 kN/m over the middle 5 m. Using an allowable stress, f = 120 MPa, determine the most economical W shape beam, with the condition that the depth of the beam shoul not exceed 500 mm [Select] V What is the actual stress in the selected [Select] beam? [Select W 310 x 117 W 460 x 97 W 460 x89 W 460 x 52

A beam simply supported on a 8 m span carries a uniformly distributed load of 30 kN/m over the middle 5 m. Using an allowable stress, f = 120 MPa, determine the most economical W shape beam, with the condition that the depth of the beam shoul not exceed 500 mm [Select] V What is the actual stress in the selected [Select] beam? [Select W 310 x 117 W 460 x 97 W 460 x89 W 460 x 52

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Use transformed sec method please
Answer problem1
I. Problem Solving. Box your final answer. 1. Find the (a) maximum tensile and compressive bending stress in the wooden beam and (b) maximum shear stress in the shaded area of a wooden beam. 1 . 4kN 2kN 3kN 2m- A 1m 1m 2m 4m 3m 8m 5m 1m
Find maximum normal stress in given beam section a-a. 6 = A MPa 30 kN 50 kN 50 kN 30 kN 2 m i a 5 @ 0.8 m = 4 m W310 X 52 B H
The steel beam has the cross section shown. The beam length is L = 5.6 m, and the cross-sectional dimensions are d = 335 mm, bf = 195 mm, tf = 12 mm, and tw = 10 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 165 MPa. Wo X Answer: Wo= 12 B 72 C kN/m
Problem 8.57 The sign is subjected to the uniform wind loading. Determine the stress components at points A and B on the 100-mm- diameter supporting post. (Eigure 1) Figure 7 of 8 > Review Determine the normal stress at point A. Express your answer using three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. HÅ ? JA= Value Units Submit Request Answer Determine the shear stress at point A. Express your answer using three significant figures and include the appropriate units. μA C ? Value Units Review Part C Determine the normal stress at point B. Express your answer using three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. μA Ⓒ ? TB - Value Units Submit Request Answer Determine the shear stress at point B. Express your answer using three significant figures and include the appropriate units.…
A distributed load of w N/m is applied over an entire length of a simply supported beam 8m long. The beam section is made up of four 20mmx100mm rectangles arranged as shown. Determine the following: a. maximum value of w without exceeding the permissible flexure stress of 10MPa. b. maximum value of w without exceeding the permissible shear stress of 1.2MPa. c. maximum value of w without exceeding the permissible screw strength of 800N for a pitch of 75mm.Please show your clean and complete solution. Thanks
A beam simply supported at the ends of a 25-ft span carries a uniformly distributed load of 1000 lb/ft over its entire length. Select the lightest S section that can be used if the allowable stress is 20 ksi. What is the actual maximum stress in the beam selected? Assume that the beam in the problem is properly braced against lateral deflection. Be sure to include the weight of the beam itself.
Beam Number 1 R₁ 25 kN-m 1m 1m 3m 10 kN/m R₂ 2 m
The steel beam has the cross section shown. The beam length is L = 7.5 m, and the cross-sectional dimensions are d = 385 mm, b = 190 mm, t+= 12 mm, and tw = 10 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 155 MPa. Wo -1/2 Answer: Wo= B sla -1/12 kN/m
A reinforced concrete beam experiences a load as shown. It has a base of 350 mm, and an effective depth of 600 mm, with 4 – 25 mm diameter rebars. The concrete has a compressive strength of 27.6 MPa, Determine the maximum distributed load that the beam can carry. Assume that the allowable stress in steel is 167 MPa (instead of 160 MPa). w 1.5 m 10 kN 1.5 m 5 m
An IPE 330 × 160 carries the load shown below. Compute the stress due to bending. 110 kN 44 KN 44 KN 2 m 2 m 0.75 m 0.75 m