An engine develops 5.0 MW at 115 RPM and the ratio of maximum to mean torques is 1.3 to 1. Calculate the diameter (in mm) of the main shaft coupled direct to the engine to transmit the power 1. а. allowing a stress of 50 MPa and assuming the shaft to be solid. b. Calculate the diameter (in mm) of the main shaft coupled direct to the engine to transmit the power allowing a stress of 50 MPa and assuming the hollow with a bore equal to half the outside diameter.

An engine develops 5.0 MW at 115 RPM and the ratio of maximum to mean torques is 1.3 to 1. Calculate the diameter (in mm) of the main shaft coupled direct to the engine to transmit the power 1. а. allowing a stress of 50 MPa and assuming the shaft to be solid. b. Calculate the diameter (in mm) of the main shaft coupled direct to the engine to transmit the power allowing a stress of 50 MPa and assuming the hollow with a bore equal to half the outside diameter.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

None
PLEASE ANSWER NUMBER 3.11 MECH 221: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
2. Two shafts, one solid the other one hollow, are connected end to end by means of a coupling in which there are 8 screws on the pitch diameter D = 250 mm. The solid shaft has diameter d = 50 mm and transfers the power P = 500 kW at 75 rev/s. The external diameter of the hollow shaft is dex = 75 mm. %3D Note: All parts of the system must be equally strong, and able to transfer the required power Calculate: (a) The internal diameter d; of the hollow shaft (b) The diameter of the bolts d, connecting the two shafts (c) If the hollow shaft has to be replaced by a rectangular hollow cross-section with outer dimensions b xh and uniform wall thickness of 4 mm. Calculate the values b, h while following the request to keep h = 2b
8.9 (A/B). A solid steel shaft of 200 mm diameter transmits 5 MW at 500 rev/min. It is proposed to alter the horsepower to 7 MW and the speed to 440 rev/min and to replace the solid shaft by a hollow shaft made of the same type of steel but having only 80% of the weight of the solid shaft. The length of both shafts is the same and the hollow shaft is to have the same maximum shear stress as the solid shaft. Find: (a) the ratio between the torque per unit angle of twist per metre for the two shafts; (b) the external and internal diameters for the hollow shaft. [L.Mech.E.] [2.085; 261, 190 mm.]
Solve the following problem Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Critically evaluate and compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of T N. m. the missing Torque 624 (T).
x Question: The diameter of shaft used in the below design is 90 mm. Identical pulleys are used in the design with a radius of 160 mm. The forces acting on the system are defined as follow: F₁ = 1P kN; F₂ = 8P kN; F3 = 2P kN; F₁ = 6P kN; F5 = 4P kN; F = 7P kN. Employing the maximum shear stress theory, calculate the maximum permissible P for a safe design experience. L₁ = 1.4m; L₂ = 1.8 m; L3 = 1.4m; L4 = 1.6 m; allow = 75 MPa (allowable strength, σs) A F₁ F₂ L2 m F4 B 3 F6 Fs
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
es/ EN6902 / General / Final Exam A Wind Turbine has a maximum output of 2MW at a speed of 20 rpm. A shaft of length 2m made of EN8 steel (properties given in the table below) is to transfer torque from the propeller to the turbine. Using a design stress for EN8 Shafting as 240 MPa. You are to: Calculate the diameter size of a solid shaft in mm, so that it will not fail due to torsion. EN8 Shafting Steel Ultimate tensile stress 850 MPa Ultimate shear stress 490 MPa Tensile Yield stress 530 MPa Shear Yield stress 300 MPa Young's miodulus Modulus of rigidity 210 Gpa 78 GPa Select one: O a. 270 O b. 136 O c. 135 O d. 272 SW
None
A shaft is transmitting 100 kW at 160 rpm. Find a suitable diameter for the shaft if the maximum torque transmitted exceed the mean by 25%. Take maximum allowable shear stress as 70 MPa.
PLEASE ANSWER NUMBER 3.9 MECH 222: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
Solve the following problem Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Critically evaluate and compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of T N. m. the missing Torque 55(T).