A hollow shaft must transmit 1400 kW at 180 rpm. The outside diameter must be 1.6 times the inside diameter. The maximum forque is 30% more than the mean torque. Calculate: 1. The diameters of the hollow shaft if the allowable stress is 200 MPa. 2. The diameter of the solid shaft if the allowable stress is 200 MPa.

A hollow shaft must transmit 1400 kW at 180 rpm. The outside diameter must be 1.6 times the inside diameter. The maximum forque is 30% more than the mean torque. Calculate: 1. The diameters of the hollow shaft if the allowable stress is 200 MPa. 2. The diameter of the solid shaft if the allowable stress is 200 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A circular shaft of 60 mm diameter is running at 150 r.p.m. What will be the torque transmitted by the shaft if (t = 80 MPa)?
Design a hallow shaft (Diameter and length) that develops 80 kN of power while rotating at a speed of 4000 rpm. The design constrains are as under: The angle of twist not to exceed 0.200 Shear stress is not to exceed 480 MN/m? The outer diameter is to be twice the inner diameter. The shaft length is to be three times the outer diameter. Modulus of rigidity = 79 GN/m?.
Design a hallow shaft (Diameter and length) that develops 80 kW of power while rotating at a speed of 4000 rpm. The design constrains are as under:The angle of twist not to exceed 0.200Shear stress is not to exceed 480 MN/m2The outer diameter is to be twice the inner diameter. The shaft length is to be three times the outer diameter. Modulus of rigidity = 79 GN/m2.
An engine develops 5.0 MW at 115 RPM and the ratio of maximum to mean torques is 1.3 to 1. Calculate the diameter (in mm) of the main shaft coupled direct to the engine to transmit the power 1. а. allowing a stress of 50 MPa and assuming the shaft to be solid. b. Calculate the diameter (in mm) of the main shaft coupled direct to the engine to transmit the power allowing a stress of 50 MPa and assuming the hollow with a bore equal to half the outside diameter. For Solid Shaft:T: = D't For Hollow Shaft:T= 16 16D Tm = P/w
Calculate the maximum allowable torque (in-lbs). A solid steel shaft is made from AISI 1045 steel, with a 9.0" diameter and length of 44". The maximum allowable shear stress on the material is 6200 psi. Based on the answer above, what is the required RPM if this shaft needs to transmit 4500 HP at the maximum allowable torque?
A hollow shaft of outer diameter 40 mm and inner diameter of 20 mm is to be replaced by a solid shaft to trandmit the same torque at the same maximum stress. What should be the diameter of the solid shaft?
Design a hollow circular steel shaft to transmit an applied torque of 360,000 in-lbs. Theallowable shear stress is 6,000 psi and the inside diameter is to be 0.6 times the outsidediameter.
Compute the torsional shear stress in a circular shaft with a diameter of 50 mm that is subjected to a torque of 800N-m.
A solid circular shaft of 35 mm diameter transmits a torque of 1460 Nm. The value of maximum shear stress is?
Compute the torsional shear stress in a circular shaft with diameter of 50mm that is subjected to a torque of 800Nm.
A hollow shaft has an inner diameter of 0.035m and outer diameter of 0.06m. Compute for the torqueif the shear stress is not to exceed120 MPa in N-m.
Two designs for a shaft are being considered. Both have an outside diameter of 60 m and are 800 mm long. One is solid but the other is hollow with an internal diameter of 40 mm. Both are made from steel (G=70 GPa). Compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of T N. m. Use the last THREE digit of your ID Number for the missing Torque (T). 575