You are asked to design a de power supply using a bridge full wave rectifier, as shown in Figure 1.d, to deliver a de voltage of Vo = 12 V to a 3 k2 load resistor with a ripple of less than 0.6 Vpp, where Vpp is the peak to peak voltage. The input voltage is a sine wave with frequency of 50 Hz. The diodes have a forward voltage of 0.7 V. i) Calculate the value of smoothing capacitor C. ii) Calculate the rms value of the input voltage, v(t).

You are asked to design a de power supply using a bridge full wave rectifier, as shown in Figure 1.d, to deliver a de voltage of Vo = 12 V to a 3 k2 load resistor with a ripple of less than 0.6 Vpp, where Vpp is the peak to peak voltage. The input voltage is a sine wave with frequency of 50 Hz. The diodes have a forward voltage of 0.7 V. i) Calculate the value of smoothing capacitor C. ii) Calculate the rms value of the input voltage, v(t).

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is the difference between a diode and rectifier?
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V. V1=5 V and V2=9 V. R www D1 Vin Vout v1 V2 Maximum voltage of output waveform Minimum voltage of output waveform
Draw vx and v0 according to the input voltages in the circuit shown in the figure. note = R1 = 10Kohm R2 = 1kohm R3 = 1Kohm, the threshold voltages of diodes will be VE = 0.7V.
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
A full-wave rectifier uses 2 diodes. The internal resistance of each diode is 20 Q. The transformer RMS secondary voltage from centre tap to each end of the secondary is 50 V and the load resistance is 980 Q. Mean load current will be
For the rectifier in the figure below, state the conduction sequence of the diodes for periods t1 to tó. D1 D2 D3 22) tl: D. & D.. 23) t2: D. & D.. 24) t3: D. & D.. 25) t4: D. & D.. D4 D5 D6 26) t5: D. &D. 27) t6: D.AN A & D....... Vm cot t6
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
You are asked to design a de power supply using a bridge full wave rectifier, as shown in Figure 1.d, to deliver a de voltage of Vo = 12 V to a 3 k2 load resistor with a ripple of less than 0.6 Vpp, where Vpp is the peak to peak voltage. The input voltage is a sine wave with frequency of 50 Hz. The diodes have a forward voltage of 0.7 V. i) Calculate the value of smoothing capacitor C. ii) Calculate the rms value of the input voltage, v(t). Figure 1.d.
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL