xxx k Pulley. mass moment of inertia J 77777. Fig.Q1 The system shown in Fig.Q1 has a natural frequency of 5 Hz for the following data: Mass moment of inertia of the pulley Jo = 5 kgm², inner radius r₁ = 10 cm and outer radius 12 25cm and attached external mass m = 10 kg. When the system is disturbed by giving it an initial displacement, the amplitude of free vibration is reduced by 80% in 10 cycles. Determine the value of spring constant (k) and damping coefficient (c).

xxx k Pulley. mass moment of inertia J 77777. Fig.Q1 The system shown in Fig.Q1 has a natural frequency of 5 Hz for the following data: Mass moment of inertia of the pulley Jo = 5 kgm², inner radius r₁ = 10 cm and outer radius 12 25cm and attached external mass m = 10 kg. When the system is disturbed by giving it an initial displacement, the amplitude of free vibration is reduced by 80% in 10 cycles. Determine the value of spring constant (k) and damping coefficient (c).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The complete slide- back and forth motion of a single reciprocating compressor piston completes in a 2-sec period. The volume displacement of the piston though the piston cylinder is 8,902.63 in3. The stiffness of crank is said to be equal to 65.5N/m and the mass of the said piston is at 10kgs. 1) The natural frequency 2) Force exerted by the piston 3) Draw the piston assembly along with its motion and position analysis
-For the vibrometer with mass (2kg) & spring stiffness (k), base excitation y(t)=b sin(wt), itation frequency=5Hz, 2Z=24mm & zeta=0.2, frequency ratio (r)=2, find: ● Wn. K. ● ● ● Amplitude ratio Z/Y. b & delta. 2 kg Structure. W D 24 mm
P.S: answer the question and plot 4 separate graphs
Calculate the natural frequencies and vibration modes of a free-vibrating 2-GDL spring-mass system, using the matrices of this system presented below. mass matrix stiffness matrix [":] m 2k -k M K: %3D т ーk 2k
The life of an automotive component can be modelled by a Weibull distribution.∝ = 6.3 ? 105, ? = 1.3 i. Calculate F(t)ii. R(t)iii. h(t) at the end of the rotating period of 36,000 miles
A 11-lb wheel is mounted on a 2-lb plate whose center is attached to a 1.6 in diameter, 30 in long (G = 11606.22 kips/in^2) steel bar, which is fixed at its other end_ The centroidal polar moment of inertia of the plate is 220 slugs-in^2. The period of torsional oscillation of this assembly is 0.15 s. What is the polar moment of inertia of the wheel?
please be specific and explain will up vote if correct
In an oscillatory motion of a simple pendulum, the ratio of the maximum angular acceleration, 0"max, to the maximum angular velocity, O'max, is Tt s^(-1). What is the time needed for the pendulum to comnplete one-half oscillation? O 2 sec O 1 sec O4 sec 0.25 sec 0.5 sec Consider a place where the gravity is one-fourth the gravity on Earth (g = g/4), that place
Please answer with explanation. I will really upvote
Maximum fluctuation of kinetic energy in an engine has been calculated to be 2600 J. Assuming that the engine runs at an average speed of 200 rpm, the polar mass moment of inertia (in kg.m) of a flywheel to keep the speed fluctuation within ±0.5% of the average speed is
1- Finding the values of the critical displacement (x) of the slide with different values of (theta) and drawing the relationship between (x) and (theta) theoretically and also finding the values of velocity and modulation theoretically with the change of angle (theta through equations (1, 2, 3) note:- r=25 mm, l=150 mm.