with diameter d = 38 mm transmits 37 kW to a gearCalculate the required speed of rotation (number ofat B. The allowable shear stress in the steel is 40 MPa.X7-3 A motor driving a solid circular steel shaftrevolutions per minute) so that the shear stress in theshaft does not exceed the allowable limit.Motord = 38 mmB

We have to determine motor driving a solid circular steel shaft 38 mm transmits 37 kW to a gear with…

X7-3 A motor driving a solid circular steel shaft with diameter d = 38 mm transmits 37 kW to a gear at B. The allowable shear stress in the steel is 40 MPa. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit. Motor d = 38 mm T B

X7-3 A motor driving a solid circular steel shaft with diameter d = 38 mm transmits 37 kW to a gear at B. The allowable shear stress in the steel is 40 MPa. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit. Motor d = 38 mm T B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The composite shaft shown in the figure consists of two steel pipes that are connected at flange B and securely attached to rigid walls at A and C. Steel pipe (1) has an outside diameter of 168 mm and a wall thickness of 5 mm. Steel pipe (2) has an outside diameter of 126 mm and a wall thickness of 8 mm. Both pipes are 2.4 m long and have a shear modulus of 79 GPa. If a concentrated torque of 22 kN-m is applied to flange B, determine (a) the maximum shear stress magnitudes in pipes (1) and (2). (b) the rotation angle of flange B relative to support A. N Swors: LI (1) TB. B L2 (2) C X
The motor supplies 11.1 kW at 19.9 Hz at A. The bearings shown permit free rotation of the shafts. Assume Ng=44 teeth and Ne=28 teeth. (a) Shaft (2) is a solid 36-mm-diameter steel shaft. Determine the maximum shear stress T2 produced in shaft (2). (b) If the shear stress in shaft (1) must be limited to 43 MPa, determine the minimum acceptable diameter d, for shaft (1) if a solid shaft is used. NB В (1) Nc Tp (2) Answers: MPa. (a) T2 = mm. (b) di =
i need the answer quickly
A steel shaft with a constant diameter of 60 mm is loaded by torque applied to gears attached to it as shown in the figure. Using G=83 GPa, determine the relative angle of twist of gear D relative to gear A.The steel shaft shown in figure rotates at 6 Hz with 55 kW taken of at A, 40kW removed at B and 95 kW applied at C. Using G =83 GPa, determine the maximum shearing stress and the rotation of gear A relative to gear C.
4. The shaft shown below, is made of ASTM-A-36 steel with Sy = 250 MPa and p = 7.86 g/cm³. The bearings at A and B only carry vertical loads. A 6m W X -ØD T As shown in the figure, the shaft is carrying a torque T = 400 Nm and its own weight per unit length w. a. Determine the location of maximum stress. b. Using the distortion energy theory, find the diameter of the shaft, D, if the desired safety factor is 2.1. C. Using the result from b. what would be the safety factor if the max shear theory is used?
Please answer by moment area method
A solid steel shaft ABC with diameter d =40 mm is driven at A by a motor that transmits 75 kW to the shaft at 15 Hz. The gears at B and C drive machinery requiring power equal to 50 kW and 25 kW, respectively. Compute the maximum shear stress and angle of twist in the shaft between the motor at A and the gear at C. Assume that G=75 GPa.
P
1. A solid steel shaft ABCDE having diameter d = 40 mm turns with a constant angular velocity and freely in bearings at points A and E. The shaft is driven by a gear at C, which applies a torque T₂ = 625 N_m in the direction shown in the figure. Gears at B and D are driven by the shaft and have resisting torques T₁ and T3, acting in the opposite direction to the torque T2. We know T₁ = 400 N.m, but T3 is not explicitly given in the problem. Segments BC and CD have lengths LBC= 550 mm and LCD = 400 mm, respectively, and the shear modulus G = 80 GPa. Determine the maximum shear stress in each segment of the shaft and the angle of twist between gears B and D. pôrôć -LBC LCD T3 E
B5
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 74 mm and G = 33.05 GPa. For the steel segment BC, the diameter is 47 mm and G = 84.69 GPa. Given that a = 2.18 m and b = 1.33 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 60.08 MPa in the bronze and 82.03 MPa in the steel. Round off the final answer to two decimal places
I really need help with this! Please answer it using the Maximum shear stress theory, and also be very clear with your explanation. Thank you!