Answered: X Your answer is incorrect. Iron has a…

X Your answer is incorrect. Iron has a BCC crystal structure, an atomic radius of 0.124 nm, and an atomic weight of 55.85 g/mol. Compute its theoretical density. 7.87 g/cm³

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 5ETSQ

See similar textbooks

Related questions

Q: 1) Draw influence line diagram for reaction at E, shear at D, and moment D. ht & A B 4m ato 2m D E

A: A continuous beam with hinged supported at A, roller supported at C and E. The beam also contains an…

Q: If the average rainfall intensity for 50 years of records is 50 mm/h (2.0 iph) for storm duration of…

Q: The assembly consists of two brass rods AB and CD and one steel rod EF between a rigid bar. If the…

A: Horizontal displacement of end F of rod EF is, ∆=0.47 mm Material Length (mm) Diameter (mm)…

Q: calculate the maximum deflection using double integration

A: Determine the Maximum deflection of the beam using Double Integration Method.

Q: Suppose a hotel having the following data: 80 Lavatories, 30 kitchen sinks, 50 laundry, 75 showers,…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: Q1) The data in the table below used to design a sedimentation tank with depth=4m and detention…

A: Sedimentation tank- Q-1 Depth d= 4 m,Detention time t=2 hr,Q=2000 L/min, SG=1.2,μ=0.89×10-3…

Q: A three-layer soil has the following properties: Layer 1: k = 2.93 x 10^-3 cm/s, H = 3.08 m. Layer…

Q: Problem 1: Determine the reactions and all bar forces for the truss shown below. E=29000ksi and…

A: The given question can be solved with the help of equilibrium equations which are: ΣFx= 0 ΣFy= 0ΣMx=…

Q: Given the following elements of a circular curve: middle ordinate = 2 m; length of long chord = 70…

Q: Please upload your full solution to the following problem. Calculate the bed life, volume of water…

A: Influent concentration of TCE, Ci = 1 mg/L Final concentration of TCE, Cf = 0.005 mg/L K = 55.9…

Q: 9. A 4.5 m saturated clay layer (two-way drainage) subjected to surcharge loading underwent 90%…

A: "Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: In a tri-axial test of a silty soil, the sample failed at normal stress of 475 kPa and a shear…

Q: A partially open sluice gate discharges water at 6 m/s with a depth of 40 cm in a rectangular…

A: A partially open sluice gate discharges water at, V1= 6 m/s. Depth, Y1= 40 cm = 0.4 m. A rectangular…

Q: Determine the shear strength of soil (in kN/m² units) in terms of effective stress on a plane within…

A: Total stress- σ=220 kN/m2, Pore water pressure- u=120 kN/m2, Cohesion C=16 kN/m2, Angle of internal…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: The below structure is given; Where, P = 440 N

Q: Calculate the maximum allowable load that a nominal 203.2) 203.2 mm (8"x8") sawn lumber column, 4.0m…

A: When the amount of load is acting on the body or specimen it goes under some amount of deformation.…

Q: find the moment of inertia of the composite area shown in the figure below. For the X- Y centroidal…

A: Following figure of the composite area is given, it is required to determine the moment of inertia…

Q: Fluid flows through a 20-mm diameter pipe, 150-m long at a Reynold's number of 1750. Calculate the…

A: we have to determine the discharge

Q: define in your own words each of the "5 D's of Development": Density, diversity, design, destination…

A: Planning and policy that incorporates the 5 D's of development can promote health and well-being…

Q: Three specimens of clay having a small air-void content were tested in the shear box. Shear loading…

Q: A 4 m thick of sand overlies a thick layer of clay. The water table is 1.8 m. below the sand…

A: We have to determine the total stress at a point 12 m below the sand surface

Q: a. Determine the safe uniform load that the beam could carry over a 5 meter b. Determine the…

A: We need to first locate the centroid of the section in order to calculate the Moment of inertia…

Q: Prepare a Grade Sheet for top-of-curb cut and fill only using the following information. Centreline…

A: Road width-12m curb face-16 cmGradient to bottom of curb-2.2%Centereline elevation- 107.560 m

Q: Replace the distributed loading by an equivalent resultant force and specify where its line of…

A: Loading structure,

Q: Calculate the MFD (maximum flooding depth) in the following road profile (not to scale). If the MFD…

Q: A circular foundation of diameter 8 m supports a tank. The base of the foundation is at 1 m from the…

A: Given Diameter, d=8m γsat=19 kN/m3γd=17.6 kN/m2ϕ=25° Load , P=20 MN Cu=80 kPa

Q: Determine the moment over the support B and C of the beam shown using Three Moment Equation.

A: ###Moment over Supports B and C using three moment Equation ###

Q: Reinforce Concrete: A rectangular beam having a width of 300mm has an effective depth of 600mm.…

A: Effective depth d = 600 mmWidth of beam b = 300 mmTotal depth of beam h = 680 mmNumber of rebars =…

Q: In the floor plan below, the rigidities of walls A, B, and C are 1.0. The rigidity of wall D is 1.5.…

A: We need to use the diaphragm method to analyze the lateral load resistance of the building. In this…

Q: 3) Explain how blimps/zeppelins are Thin-Walled- Pressure-Vessels. Explain how and give some…

Q: 3) A beam carries uniformly distributed load of 60 kg/m rests on three supports spaced 1.2 m apart.…

A: Determine the overhange length (x) such that all support reaction shall be the same.

Q: Given the following elements of a circular curve: middle ordinate = 2 m; length of long chord = 70…

A: Circular curve Length of long chord (L) = 70m Mid ordinate (M) = 2m Determine the degree of curve…

Q: 50 cm-long circular rod has a diameter of 10 mm and is acted pon by a 20 kN load acting to its…

A: Length of rod = 50 cm Diameter of rod = 10 mm Load = 20 KN E = 200 Gpa

Q: Question 1 The velocity component in x and y direction are given by u= Axy-xy^²: v=x²y - 4y³. the…

A: The velocity component in x and y directions- u=λxy-xy2,&v=x2y-4y3.

Q: Determine the LRFD design tensile strength and the ASD allowable tensile strength for the…

A: Fy = 36 ksi Fu = 58 ksi 3/4 inch diameter A325 grade bolt Calculations shown in steps below

Q: Problem 1. (P10.1). For the truss shown below, compute the horizontal and vertical components of…

A: we have to determine the horizontal and vertical component of displacement of joint BDraw free body…

Q: Question # 3: A cast iron beam is of 1-section as shown in Figure below. supported on a span of 5…

A: Simply supported beam with uniformly distributed load and span of 5m. Maximum tensile stress = 20…

Q: A beam (ABC) has a pin support at the left-hand edge (point A) and is supported by a thinner beam…

A: "Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 3.5 through 3.13 Determine the reactions at the supports for the beam shown. 30 kN/m A FIG. P3.5 10…

Q: A sign of weight 3000 N is supported as shown by a ball and socket support at A and two cables BC…

A: As per guidelines we need to answer only first 3 subparts of question so please repost rest…

Q: he box girder below is subjected to a shear of V=15kN. Determine the shear flow at point B. Give…

A: The magnitude of the shear force on the box girder = V = 15 kN To determine:- a) The shear flow at…

Q: Situation 36 Considering the contraption shown in figure, AB = 450 mm, BC = 225, mm BD = 480 mm, CE…

Q: 4. Determine the moment produced by the 4 forces about point A. Use F = 400 N, a = 0.5 m, and h =…

Q: Check the stability of concrete retaining wall shown in figure against sliding and bearing capacity.…

A: Let us first calculate the active force through the backfill Active force = Area of Active pressure…

Q: Question 4 At a point in a material there are two direct stresses of 60 MPa tensile and 50 MPa…

A: Two direct stresses 60 MPa tensile and 50 MPa compressive acting at right angles to each other. The…

Q: Determine the slope at point D of the beam shown using the Virtual Work Method. (You can verify…

A: To determine the slope at point D

Q: Q.3. For the frame shown in Fig., find all the required equations to find moments by…

Q: 5. Determine the moment over the support B of the beam shown using Three Moment Equation. A 4.5 m B…

Q: A horizontal water pipe is reduced in size from 18 in. in diameter at point A to 6 in. in diameter…

Q: A footing 3m x 3m is supporting a concentric load of 1100 kN. 1.5m 3.0m Xd = 1

Concept explainers

Analysis and Procedures for Material Selection

The term material selection means to select the right material for various engineering applications. There are various engineering materials available and each has different individual properties. Thorough knowledge of the material properties and behavior is crucial in the design process. For instance, a structural member, such as a beam, is used to support vertical shear loads by the building itself. To withstand such loads, the material of the beam must possess adequate strength and stiffness to resist any deformation that might lead to the formation of cracks.

Question

* Your answer is incorrect.
Iron has a BCC crystal structure, an atomic radius of 0.124 nm, and an atomic weight of 55.85 g/mol. Compute its theoretical density.
7.87
g/cm³

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Explanation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis and procedures for material selection

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two hypothetical metals are created with different elements that have the same atomic mass (g/mole) and the same atomic radius. Metal A has a density of 9.50 g/cm3 and metal B has a density of 8.73 g/cm3. If one of these metals has a BCC lattice structure and the other has an FCC lattice structure, identify the structure that corresponds to each of one of them. Justify your answer.
A pure titanium cube has an edge length of 2.74 inin . How many titanium atoms does it contain? Titanium has a density of 4.50g/cm34.50g/cm3. Express your answer in atoms to three significant figures.
Two hypothetical metals are created with different elements that have thesame atomic mass (g/mole) and the same atomic radius. Metal A has a density of 9.50 g/cm3 and metal B has a density of 8.73 g/cm3 . If one of these metals has a BCC lattice structure and the other has an FCC lattice structure, identify the structure that corresponds to each of one of them. Justify your answer.
Question 6 (of 8) 6. The density of platinum is 21500 kg/m³ and that of aluminum is 2702 kg/m³. Find the ratio of the volume of 1.80 kg of platinum to the volume of 1.17 kg of aluminum.
Two hypothetical metals are created with different elements that have the same atomic mass (g/mole) and the same atomic radius. Metal A has a densityof 9.50 g/cm3 and metal B has a density of 8.73 g/cm3. If one of these metals has a BCC lattice structure and the other has an FCC lattice structure, identify the structure that corresponds to each of one of them. Justify your answer.
Determine the density of a hypothetical BCC metal having an atomic mass of 63.5 g/mole and atomic radius of 0.128 nm.
At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown in the figure. Bar (1) is an aluminum alloy (E-10,000 ksi; u= 0,32; a= 12.5 x10°/°F] bar with a width of 3 in, and a thickness of 0.75 in. Bar (2) is a stainless steel |E-28,000 ksi; u=0.12; a=9.6x10°/°F] bar with a width of 2 in. and a thickness of 0.75 in. The supports at A and C are rigid. Determine the normal stress in bar (1) at a temperature of 450°F
Copper has an atomic radius of 0.128 nm (1.28A°), an FCC crystal structure, and an atomic weight of 63.5 g/mol. Compute its theoretical density?
Calculate the radius of the copper atom, given that copper has an FCC crystal structure, a density of 8.89 g/cm3, and an atomic mass of 63.55 g/mole.
Metal X has an atomic weight of 43.1 g/mol, theoretical density of 6.40 g/cm^3, and atomic radius of 122 pm. Determine whether the crystal structure of Metal X is BCC, FCC, or simple cubic. Provide your complete solution.
Calculate the volume of the unit cell of iron in cubic meters, given that iron has a body-center cubic crystal structure and an atomic radius of 0.124 nm.
Draw a bar diagram on your sketch paper based on the table below and determine the non-carbon hardness (permanent hardness) in mg/L of CaCO3. Atomic weight Equivalent weight or molecular Concentration (mg/L) meq/L concentration (mg/meq) weight (g/mol) 100 Ca2+ 40 150 mg/L as CaCO3 150/50=3 (g/mol)/2(eq/mol)=50 Mg2+ 24 100 mg/L as CACO3 100/50=2 Na+ 23 46 mg/L K+ 39 39 mg/L HCO3 61 225 mg/L as CaCO3 225/50=4.5 SO42- 96 72 mg/L CI 35.5 71 mg/L O 25 mg/L of CaCO3 O 50 mg/L of CaCO3 O 100 mg/L of CaCO3 O 150 mg/L of CaCO3