With diagram .In a steam jet refrigeration system, the evaporator is maintained at 6°C. The chilled water leaves at the same temperature and warms to 11°C as it absorbs the load. Make-up water in available at 25°C. For a capacity of 50 tons, determine the volume of a vapor removed. Ans. (a) 8.381 kg/s, (b) 10.07 m3 /s

With diagram .In a steam jet refrigeration system, the evaporator is maintained at 6°C. The chilled water leaves at the same temperature and warms to 11°C as it absorbs the load. Make-up water in available at 25°C. For a capacity of 50 tons, determine the volume of a vapor removed. Ans. (a) 8.381 kg/s, (b) 10.07 m3 /s

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter50: Commercial, Packaged Rooftop, Variable Refrigerant Flow, And Variable Air Volume Systems

Section: Chapter Questions

Problem 22RQ: Variable refrigerant flow systems sense the ______and _____of the refrigerant to determine the...

See similar textbooks

Similar questions

In order to remove moisture from a refrigeration system using a vacuum pump, it must be in a _____state.
Q.1. A refrigeration process with interstage cooling uses refrigerant HFC-134a, and the outlet of the condenser is to be saturated liquid at 40°C. Refer to the following figure for stream numbers in your solution. The pressure of the flash chamber and the intermediate pressure between compressors is to be 290 kPa. The evaporator is to operate at -20°C and the outlet is to be saturated vapor. The flowrate of stream 1 is 23 kg/h. The flash chamber may be considered adiabatic. The compressors may be considered to be 80% efficient. a) What is the power input required to the first compressor? b) What are the flowrates of streams 6 and 7? What is the enthalpy of stream 4? Hot Side 6 5 Condenser 2nd Stage Compressor Throttle Valve 7 Flash Chamber Vapor Phase Only 1st Stage Compressor 8 Throttle Valve Evaporator 1 2 Cold Side
For a 10-ton-capacity refrigeration system, the pressure of refrigerant in the evaporator is 150 kPa, whereas in the condenser it is 950 kPa. If refrigerant R-134a is used under saturated conditions, calculate the theoretical power required to operate the compressor = ... KW
Q.2: A refrigeration system using refrigerant 22 is to have a refrigerating capacity of 80 kW. The cycle is a standard vapor-compression cycle in which the evaporating temperature 42°C. -8°C and the condensing temperature (a) Determine the volume flow of refrigerant measured in cubic is meters inlet at the to the compressor. second per (b) Calculate the power required by the compressor. (c) At the entrance to the evaporator what is the fraction of vapor in the mixture.
3.) The steam power plant requires 100 gallons per minute to cool the steam in the condenser from an exhaust pressure of 100 kPa. The feedwater pressure is 100 bar and 500 degrees Celsius. The condensate leaves the condenser at saturated liquid. The cooling tower temperature for the leaving cooling water is 25 degrees Celsius and the cooling water leaving the condenser is 42 degrees Celsius. Calculate the mass of the steam in kg/s assuming ideal rankine cycle and standard density of cooling water.
Q1: Steum at a pressure of 28kpa is passed into a condenser and it leawes as condensate at a temperature of sac Cooling water circulates through the condenser at the rate of 45 kg/min - It enters at 152 and Veaves at 3oc If the Steam flow rate is 1.25 eg/min, determinė the drynes fraction of Steam as it enters the condenser.
Evaporative cooling PLEASE DO NOT USE PSYCHROMETRIC CHART. THANK YOU In the diagram below inlet air is drawn over a pool of liquid water in a steady-state, steady-flow isobaric process. Evaporation on the pool resultsin saturated air at the exit. The pool of liquid water is assumed to be at the same temperature as the exitair. Discharge fans at the exit provide a volumetric flow rate of 800,000 ft3/min. In the diagram above inlet air is drawn over a pool of liquid water in a steady-state, steady-flow isobaric process. Evaporation on the pool resultsin saturated air at the exit. The pool of liquid water is assumed to be at the same temperature as the exitair. Discharge fans at the exit provide a volumetric flow rate of 800,000 ft^3/min. Problem #1: Assume that the exit temperature is T2 = 90 °F. For this model of the system and from thedata provided determine:a) The mass flow rate dry air through the system (lbm/sec).b) The rate of heat that is output from the R-134a condenser Qout…
A manufacturing company is intending to use its water cooled condenser for its proposed cold storage room. The name plate of the condenser gives the following specifications: refrigerant ammonia condenser water inlet 30 OC condenser water outlet 40 ỌC condensing temperature 35 OC refrigerant flow 3.84 kg/min circulating water flow 120 kg/min If the company decided to purchase a new compressor and evaporator, find the tonnage of the system and the temperature in the evaporator, (b) what is the COP? (c) find the theoretical hp required.
iii) the exit area of the nozzle. Take Cp = 1.005 kJ/kg-K and R=287 J/kg-K Q.B3. A heat engine operates between two reservoirs at 400°C and 30°C. Half the power produced by the heat engine is used to drive a Carnot heat pump that removes heat from the cold surroundings at 2°C and transfers it to a house maintained at 27°C. The heat engine is absorbing heat at a rate of 5 kJ/s. i) Draw the complete schematic of the device ii) Determine the thermal efficiency of the heat engine iii) Determine the coefficient of performance of the heat pump iv) Determine the rate of heat loss from the house. v) Determine the minimum rate of heat extraction by the heat pump, and vi) the total rate of heat rejection.
1. The mean effective pressure of an engine running at 300 rpm is 500 kPa. What is the indicatedpower if the engine has bore of 250 mm x 450 mm. Select the correct answer below: A. 110.5 kW B. 150 kW C. 200 kW D. 182. 2 kW 2. In a certain process, entering is 1500 KJ/kg and 150 m/s. If the energy leaving is 12000 Kj/kg/ Determine the velocity at exit. Select the correct answer below: A.) 145 m/s B. 1020 m/s C. 789 m/s D. 978 m/s
A chiller tank with a water volume capacity of 20 M3. There are 2 chiller units with a capacity of 20 PK each to cool the water in the chiller tub. 1 unit of cold chiller water transfer pump is used to the production area with a capacity of 5 M3/hour. The chiller water temperature sent to production is 15 oC and the pressure is 4 bar. The distance of the 2 inch stainless pipe from the chiller pump to the double jacket mixing tank production is 100 meters. The diameter of the inlet and outlet pipes for the double jacket mixing tank is 1 inch. The chiller water storage capacity in a conventional double jacket mixing tank is 400 liters. (mixing tank capacity is 1500 kg). Questions: 1. How much time is needed to cool the water in the mixing tank from the initial temperature of 90 oC to 40 oC? 2. How much energy (BTU) is needed to cool the water temperature from 90 oC to 40 oC? 3. How much energy is lost along the 100 meters of chiller water transfer pipe? 4. If the number of 1500 Kg…
When an evaporator experiences a heat- load increase, the suction pressure A. remains constant.