A car jumps out of gear into neutral, particularlywhen decelerating or going down hills: Technician Achecks the shift lever and external gearshift linkagefirst. Technician B says that the clutch pilot bearingcould be the problem. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor B

Q: While diagnosing a complaint of excessive play in the steering on a vehicle with power steering:…

A: The correct option is b.

Q: when adjusting a heavy-duty pull type manual adjusting clutch what is used to compensate for normal…

A: There are two types of clutch adjustment mechanisms: 1) Manually adjusted clutch 2) Self-adjusting…

Q: Describe the purpose of a viscous clutch.

A: Viscous clutch The clutch is part of the machine that is used to operate for the transmission's…

Q: What is used in a typical 4WD pickup truck to prevent driveline windup during turns?a. Constant…

A: Constant velocity joints in the driveshafts of a typical 4WD pickup truck are used to allow for…

Q: Technician A says that some small cracks in the accessory drive belt may be within tolerance.…

A: Technician A says that some small crack in the accessory drive belt may be within tolerance limits.…

Q: When discussing the possible causes for a shudder during acceleration, Technician A says that a worn…

A: Shudder is taken place during acceleration at higher speed. The main reason of this problem is…

Q: Explain the phenomenon of engine knock

A: The metallic ping sound produced by the engine is known as engine knocking. It may be the result of…

Q: Tech A says that camber changes as the suspension moves up and down.  Tech B says that camber…

A: Camber angle : The angle made by the vertical axis with the wheel is known as camber angle . It is…

Q: Technician A says that some systems use a special modulated shift control solenoid. Technician B…

A: In automobile the transmission system uses shift control solenoid which shift the gear…

Q: Technician A says that a malfunction of the ABS causes the control module to shut off or inhibit the…

A: The system will be shut down if any malfunction is monitored in the ABS because the control module…

Q: 81) Technician A says the quality and feel of a transmission shift depends on the amount of slippage…

A:

Q: Which of the following components is replaced as an assembly?a. The transfer caseb. the viscous…

A: Step 1:The transfer case is often replaced as an assembly due to several reasons :Transfer cases are…

Q: Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the…

A: A drum brake is a brake that uses friction caused by a set of shoes or pads that press outward…

Q: What results from having different axle ratios on thefront and rear of a 4WD vehicle when it is…

A: Given Data : 4WD Axle ratio

Q: what will happen as the clutch disc wears? a. transmission shifting becomes easier b. clutch pedal…

A: The correct option is: c. clutch pedal free play increases. As the clutch disc wears, the friction…

Q: vehicle is producing a sharp, metallic rappingsound originating in the upper portion of the…

A: As per suggestion of Technician A: If the vehicle is producing sharp, metallic rapping sound from…

Q: When discussing shift problems, Technician A says that worn or broken engine and transaxle mounts…

A: A chain of gears which is used to pass on the power to the wheel from the engine is called as…

Q: Technician A says that an in-line six-cylinder diesel engine is usually longer and heavier than a V8…

A:

Q: A rough, growling noise that is heard from a transaxlewhile it is in neutral with the engine…

A: The clutch is engaged, the engine is running, and the gearshift is in neutral. One of the most…

Q: Automatic transmissions use a __ instead of a clutchto transfer power from the flywheel to the…

A: An automated car is one that has an automatic gearbox and does not require the driver to manually…

Q: Technician A says that some shift solenoids can be activated by providing a ground for the solenoid.…

A: The shift solenoid is used in the gear assembly which shifts the gear according to the desire of…

Q: Pinion gear-to-flywheel ring gear clearance is beingdiscussed: Technician A says that if there is…

A: Given  Pinion gear-to-flywheel ring gear To find Which technician is correct

Q: Technician A says that a malfunction of the ABS causes the control module to shut off or inhibit the…

A: Automobile

Q: 49.--------------occurs When the clutch is fully engaged, the driven disc does not rotate at the…

A: Clutch is a machine component that connects/disconnects the engine from the transmission drive. It…

Q: Technician A says that the engine oil drain plug typically needs to be replaced with a new one at…

A: At every maintenance trip of the automobile engine oil is changed by removing the oil drain plug.

Q: While discussing the different types of pressureplates: Technician A says that coil spring types…

A: Option D is the correct naswer

Q: Which of the following is part of the sprung weight ofa vehicle?a. Steering linkageb. Tiresc.…

A: A vehicle’s sprung weight is supported by springs of one kind of or another (coiled springs, air…

Q: Three factors to consider before deciding to apply a transmission of gear drives

A:

Q: When removing the balance shaft assembly: tech a inspects the bearings for unusual wear or damage.…

A: Balance shafts are serviced in the same way as crankshafts.there are two main causes of removing or…

Q: Interaxle differentials are being discussed. Technician A says the interaxle differential is located…

A: It is an separate differential gear box that locks the first and second differential in a tandem…

Q: Technician A says that broken or worn engine and transaxle mounts can cause a transaxie to have…

A: Given Transaxle problem To find Statement with is/are correct Shifting problem of transaxle can be…

Q: clutch is fully engaged, the driven disc does not rotate at the same speed as the driving members *

A: Slipping occurs when the clutch is fully engaged and the driven disc does not rotate at the same…

Q: The typical RWD drive shaft rotates how many times faster than wheels

A: The typical Rear Wheel Drive (RWD) shaft  rotates three times faster than the wheels,

Q: Which of the following ensures proper timing of the intake and exhaust valve events?

A: The timing of the intake and exhaust valve events helps in proper timely working of the engine.

Q: the number one cause of clutch disc failure

A: Clutch :- The function of a clutch is to transmit the power from rotating shaft or motor or engine…

Q: In a typical all wheel drive automatic transaxle, what controls the transfer clutch?a. Transmission…

A: In a typical all-wheel-drive automatic transaxle, the transfer clutch isn't directly controlled by a…

Q: Explain three different methods of clutch pedal adjustment.

A: Clutch plays an important role to help the driver in controlling transmission i.e. gearshift while…

Q: Technician A says a purpose of a lockup piston clutch is to improve fuel economy. Technician B says…

A: As we know that the purpose of lockup piston clutch is to improve fuel economy as well as it is…

Q: Technician A says that negative caster provides directional stability . Technician B says that pos…

A: Caster refers to the angle of the steering axis on a vehicle wheel from the straight line of the…

Q: A clicking noise during transmission/transaxle operationmay be an indication of __ .a. worn…

A: Given Data : Clicking Noise  Transmission operation

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.