Which of the following statements are true if drum D rotates clockwise with a constant angular velocity a) magnitude of point A and point X are the same b) acceleration of point X will have a nonzero tangential component c) the magintude of acceleration of point A is greater than point X d) the magnitude of acceleration of Point X is greater than Point A

Which of the following statements are true if drum D rotates clockwise with a constant angular velocity a) magnitude of point A and point X are the same b) acceleration of point X will have a nonzero tangential component c) the magintude of acceleration of point A is greater than point X d) the magnitude of acceleration of Point X is greater than Point A

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter20: Shop Math And Weld Cost

Section: Chapter Questions

Problem 24R: What is a dimensioning tolerance?

See similar textbooks

Similar questions

10 cm| 10 cml -20 cm B A 20 cm
B P. 200 mm 240 mm 60 30 KN Figure (1.15)
Q6. The thin plate with four holes as shown in Figure Q6 has a mass per unit area of 33 kg/m². The radius r for each hole is 50 mm. The thin plate has the dimension of 400 mm x 400 mm and suspended at pin at A. (a) Calculate the mass moment of inertia of the thin plate with four holes about an axis passing through its mass centre G, Ig.
In this case, the applied force is always pulls upward, but the amount of force that can be applied can vary between 0-350 N (maximum). The locations of the applied force and resistance cannot be changed. Which of these statement is true? Select one: O The system could lift any resistance less than, but could not lift a resistance = 250 N. The system could lift any resistance that was 350 N. O The system could raise, but would be unable to lower a resistance.
Q1 (a) During construction of a highway bridge, the main girders as shown in Figure Q1(a) are cantilevered outward from one pier toward the next. Each girder has a cantilever length of 45 m and an I-shaped cross section with dimensions shown in the Figure Q1(a). The load on each girder (during construction) is assumed to be 9.1 kN/m, which includes the weight of the girder. (Notice that there are four girders used in the construction of the bridge). Determine the maximum bending stress in a girder due to this load.
a)The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is 125 mm. calculate the cubic capacity of the engine in cubic centimetres (cm3 ); and calculate the clearance volume per cylinder for a compression ratio, r, of 8.75. b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 38 mm and the stroke of each piston is 165 mm. During testing, the engine runs at 180 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 3.4 cm2 and a diagram length of 1.2 cm. The pressure scale on the indictor diagram is set to 150 kN/m2 per cm. Calculate the mean effective pressure (m.e.p) and the indicated power developed by this four-cylinder four-stroke engine.
When does the reduction in the dimensions occur?
What is its minimum width if it produces 1000 minima?
1. Is there a difference between the values of Qideal calculated by equation (7) and Qact by using equation (Qaet=Vol/time)? Why? 2. Is there a difference between the values of Qact calculated by equation (8) and Qact by using equation (Qact=Vol/time)? Why? 3. Is there a difference between the values of the ideal diameter and the actual diameter? Why? 4. Is there a difference between the values of Ca calculated by equation (10) and Ca by using equation (11)? Why? 5. What is the relationship type in the plot between the water height in piezometer tube (Ho) and the actual discharge Qact? Why?
This refers to the attached drawing 11A003. What is dimension B?
I'm not sure how the values for the last two rows were found.
When do the actual dimensions occur?