Which of the following ratings (PIV- Peak Inverse Voltage and temperature) is true? O Si diodes have lower PIV and wider temperature ranges than Ge diodes. O si diodes have higher PIV and narrower temperature ranges than Ge diodes. O Si diodes have lower PIV and narrower temperature ranges than Ge diodes. O Ge diodes have lower PIV and smaller temperature ranges than Si diodes.

Which of the following ratings (PIV- Peak Inverse Voltage and temperature) is true? O Si diodes have lower PIV and wider temperature ranges than Ge diodes. O si diodes have higher PIV and narrower temperature ranges than Ge diodes. O Si diodes have lower PIV and narrower temperature ranges than Ge diodes. O Ge diodes have lower PIV and smaller temperature ranges than Si diodes.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 3RQ: Diodes and rectifiers allow current to _________. flow in one direction only flow in both...

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is the difference between a diode and rectifier?
Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
Assuming an ideal diode model for all the diodes in the circuit below, chose the correct state (bias) for each diode. R1 ww 9kQ 1N1199C R2 D1 18kQ 1N1199C V2 12 V R3 1kQ D3 1N1199C R4 D3: On (Forward Bais) D3: Off (Reverse Bais)
For the circuit shown in the Figure, if the diodes are silicon diodes with Vp(on)=0.7 V, and VIN=50 sin wt V, V1 =6 V and V2 = 16 V, then the value of VouTP-p) is: R, D VaN Vout v1事 2章 Oa. 25.4 V Ob. 27.4 V Oc. 29.4 V Od. 23.4 V
For the circuit below, assume the diodes operate with a constant voltage drop of .7V, find Vx, Vy, VD4 and ID2. 15V 15V Allt V1 V2 R1 1k IDC 1mA Vx R2 2k ww D1N4002 Vy D1N4002 7D1 D1N4002 D2 D3 R3 1k D4 D1N4002
Q4) Determine and sketch the output voltage across the load resistor (RL) for the circuit shown below. (assume Si diodes) V_DC 0.75 0.25 V_SIN Y SIN as RL -1 v SOR V_SQR 0.75 -0.75 V_TRI V TRI as
2. Figure A.1 shows I-V characteristics of two diodes, namely A and B. Diode A has higher dynamic resistance than diode B. UTM &UT ID 4 5UTM 3TM UTM UTM &UTM 5 UTM & UTM UTM 3 UTM 03 TM 6 UT 0.68 (a) UTM VD Figure A.1 State one possible reason why the diodes have different knee voltage values. UTM OM & UTM 3 UTM & TM (b) Based on Figure A.1, identify the knee voltage of UTM" TM 5 UTde BE UTM
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Given the following circuit with VDD= 9.2 V, R=2.3 k2, then the current Iis: Use the CVD model for the diode, with VD = 0.65 V. I VDD a. 0.004000 A O b. 3.717391 A OC. 0 A d. 4.000000 A e. 0.003717 A R + VD -