2. Figure A.1 shows I-V characteristics of two diodes, namely A and B. Diode A hashigher dynamic resistance than diode B.UTM &UTID 45UTM 3TM UTMUTM &UTM5 UTM & UTM UTM3 UTM 03 TM 6 UT0.68(a) UTMVDFigure A.1State one possible reason why the diodes have different knee voltage values.UTMOM & UTM3 UTM &TM(b) Based on Figure A.1, identify the knee voltage ofUTM"TM5 UTde BE UTM

Brief description: Diode is a directional device which will allow current to pass only in one…

(a) UState one possible reason why the diodes have different knee voltage values higher dynamic resistance than diode B. 2. Figure A.1 shows I-V characteristics of two diodes, namely A and B. Diode A has higher dynamic resistance than diode B. S UTM &U ID UTM TM & UTM S UTM & UTM & UTM & UTM 5 UTM UTM 03TM & UT 0.68 S UTM (b) Based on Figure A.1, identify the knee voltage of diode B. Figure A.1 3 UTM DM 5 UTM UTM

(a) UState one possible reason why the diodes have different knee voltage values higher dynamic resistance than diode B. 2. Figure A.1 shows I-V characteristics of two diodes, namely A and B. Diode A has higher dynamic resistance than diode B. S UTM &U ID UTM TM & UTM S UTM & UTM & UTM & UTM 5 UTM UTM 03TM & UT 0.68 S UTM (b) Based on Figure A.1, identify the knee voltage of diode B. Figure A.1 3 UTM DM 5 UTM UTM

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

V, is a 60Hz source with a peak voltage VP-120V is feeding a rectifier, assume ideal diode. The load resistance has a value of R= 10 k0. If ripple voltage Vr = 2V, the Diode average current Ipavg is VI Select one: a. + e. None Ob. 580mA Oc. 850mA Od 245mA 425mA D C: www tu Vo Q6
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
Problem # 4 In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VpC e. PIV (Peak Inverse Voltage) 10:1 Dy 1ISV ms Ouiput RL 2.2 k2 D, 50 pF All diodes are IN4001. alleee
Determine the minimum value and the maximumvalue that the series resistor may have in a regulatorcircuit whose output voltage is to be 25 V, whose inputvoltage varies from 35 to 40 V, and whose maximumload current is 75 mA. The Zener diode used in thiscircuit has a maximum current ratingof 250 mA.
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
For the circuit in the figure, let V input = 8V, Ri = 12ohms, RL = 10ohms, and VZ = 3.3V. Determine the voltages and currents of the resistors and the current of the zener diode.
Zener diodes are special purpose diodes designed to operate in their breakdown regions. Describe the working principle and characteristics of a typical Zener diode found in the market place. The Zener-diode regulator circuit shown below is to be used to provide a stabilised output to the load. The zener diode characteristic is also shown. Find the load voltage and source current if the battery voltage is 20 V, series resistance is 1.4 kohm and load resistance is 6 kohm
For the circuit shown below, sketch to scale the output V waveform and draw the transfer characteristic (V versus Vi), Assume the diodes are ideal.
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
Find the interval of values that keep the zener diode “on”. (Draw the Vy-Vi graph)
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
5) The figure below illustrates a simple voltage threshold detection circuit. To understand how it operates, we will analyze its behavior based on the simple constant voltage drop model for both diodes. Assume the Zener diode (Z1) only conducts when its breakdown voltage of 10V is reached. Di is a red light emitting diode (LED). Assume it conducts after its forward bias voltage of 1.8V is reached. Vin is unknown. Assume Zj acts as a perfect Zener diode (without series resistance). What voltage does Vin have to reach before there is a current through R¡? What voltage must Vin reach before current flows through R2? Write an equation for the current through Zi in terms of Vin, Rị and R2 that is valid when Vin is high enough for both diodes to be conducting. a. b. c. R2 Vino R1 LED