Which of the following is the most suitable for extraction in a system having very low- density difference? a. mixer-settler extractor c. pulsed extractor b. centrifugal extractor d. packed extraction tower

Q: 2. Explain in short major engineering difficulties in water treatment process

A: This question is based on water treatment process and the engineering difficulties associated with…

Q: Derive the Kremser equation for a stripper with three equilibrium stages

A: Kremser equation for stripping section is to be derived.

Q: Use water as a drilling mud to drill a well to a depth of 3000 feet , calculate the pressure…

A: This question is based on pressure gradient. The data given are: Depth = 3000 feet

Q: What is the material and energy balance of liquid liquid extraction process

A: Liquid-liquid extraction: Liquid-liquid extraction is a separation operation in which the solute…

Q: Define the two types of stress waves ?

A: The two types of stress waves are to be defined.

Q: (1) Explain the following terms: i) Slack and Raw wax

A: Slack Wax: It is yellow to dark in color. It is also known as crude paraffin wax. It is separated…

Q: What is the formula for crushing efficiency, given specific surface area of a product, mass…

A:

Q: Discuss the following:1. The similarities and dissimilarities between wet scrubbing process and gas…

A: Wet gas scrubbers are devices that are used to remove a variety of pollutants from exhaust gas from…

Q: 3 Briefly describe the drilling problems related to drilling fluid rheological property.

A: In fluid mechanics, rheology is the type of study of the flow of matter, matter could be in the form…

Q: Use equations and words to describe how stirring a solution will affect the mass-transport limited…

A: The current that flows through a solution at any time is a direct measure of the rate of the…

Q: A B Rate of deformation, duldy Shear stress, 7

A: There are several properties defined for fluid such as density, specific gravity, viscosity, etc. In…

Q: In general, why should the operating pressure be high and the operating temperature be low for an…

A: The reason for the high pressure and low temperature for the absorption process is to be mentioned…

Q: Is pinch point always located at the feed stage?

A: The location of the pinch point is to be mentioned.

Q: If the temperature profile in a rectangular slag is represented by: T(x,y,z)=x2-2y2+z²-xy+2yz…

A: The points where spacial derivatives wrt to time are 0 will be where Temperature won't change. We…

Q: What is the difference between truncation error and stability?

A: To understand the answer to this problem knowledge of Process control systems is required. The given…

Q: crystallization mechanism,

A: Crystallization is a process in which mass transfer of solute takes place from the liquid solution…

Q: A cylindrical rock sample has a porosity of 14%. The dimensions of the core are 13 cm in length and…

A: Given that, Porosity = 14% Length L = 13 cm Diameter D = 6 cm It is required to calculate the pore…

Q: Illustrate and discuss the process flow for the manufacture of porcelain

A: Solution-Step:  (a) Component needed(i) Feldspars K2O.Al2O3.6SiO2 & Na2O.Al2O3.6SiO2(ii) Quartz…

Q: Explain Process of extraction cooking oil about description and conditions process

A: Extraction is a process in which one or more components are separated selectively from a liquid or…

Q: What is the difference between the loading point and the flooding point in a packed column?

A: Loading Point and flooding points refer to the operating conditions of packed column.

Q: In the plate and frame filter press, by plotting the filtrate volume as a function of time per…

A:

Q: Convert a viscosity of 20 (g)/(cm)(s) to the American Engineering units (Ibr)(hr)/(ft?)

A: Given viscosity is 20 g/cm s Viscosity unit of g/cm s have to convert into American Engineering unit…

Q: Calculate the following: Thermal conductivity of brass Calculated quantities Value Difference in…

A: Hi, thank you for posting the question. According to our guidelines, we are allowed to answer only…

Q: Determine the terminal settling velocity of a coal particle of size 400 micron in water at 20 oC by…

A: We need to find settling velocity of coal particle water and then we need to compare it with…

Q: 5. Physical properties of the formation crude oil includes volume coefficient and viscosity.

A: The physical properties of crude oil vary according to its composition, the relative abundance of…

Q: Explain path line in relation to fluid mechanics.

A:

Q: Why are Vertical flow-through beds preferred in RTO technology?

A: Regenerative Thermal oxidizers are used to remove air pollutants. The oxidizers will help in the…

Q: In the laboratory experiment "Plate and Frame Filter Press" 1. Discuss its significance, and…

A: Filtration is the process of separation in which solids from the fluid sepaarted by passing through…

Q: Give an example of a hybrid system that involves recycle.

A: An example of a hybrid system that involves recycle is to be mentioned.

Q: It is necessary to determine the process flow diagram for the plant in the design of the material…

A: A process flow diagram is a diagram that gives the idea about the process, that is to be…

Q: 2. List the most important pipe friction formula.

A: Introduction: The friction loss in uniform, instantly sections of pipe, called "major loss", is…

Q: If the area under the stress and strain curve is less then it is concluded that the material has low…

A:

Q: Calculate the porosity of the core

A: Given data: The density of the oil = 0.85 g/cc Weight of dry sample in air = 42.4 g Weight of the…

Q: Present one example depicting the impact of instrumention on one or more process variables.

A: Consider a Water tank with a level controller. Here consider the different process variables. Input…

Q: Using a flow chart, show how a lubricant oil with high viscosity index can be manufactured from…

A: In petroleum industries, Crude oil is a type of fossil fuel that is a naturally occurring petroleum…

Q: Which of the following material has the least strain? O a. Elastic band O b. Copper wire O c. Steel…

A:

Q: Charpy impact test is conducted in a very similar manner to the Izod impact test. Difference is: *…

A:

Q: Provide an equipment description of Slurry Settler in FCC with reference:

A: To provide an equipment description of Slurry Settler in FCC (Fluid Catalytic Cracking) Dear…

Q: Explain the friction between the mater (soled with soled, liquid with liquid)?

A: Motion: Motion is the phenomenon in which an object changes its position over time. Motion is…

Q: (b) The general characteristics of three oil wells selected for artificial lift as production method…

A: Table of 3 well are given.

Q: Explain Process of extraction oil lubricant about description and conditions process

A: A lubricant is a substance that helps to reduce friction between surfaces in mutual contact, which…