Equally spaced trays are placed and provided with downspout and weirs inside the tray tower is to a. No contact between gas and liquid takes place inside the column O b. Increase the contact between gas and liquid outside the column c. Increase the contact between gas and liquid inside the column O d. Reduce the contact between gas and liquid

Q: the equivalent length of the exchanger as a complete unit (in terms of 20 mm diameter tube).

A: Consider a heat exchanger of length 12m, 10 close return bends and 15 x 90° elbows connected in…

Q: Use water as a drilling mud to drill a well to a depth of 3000 feet , calculate the pressure…

A: This question is based on pressure gradient. The data given are: Depth = 3000 feet

Q: Choose the correct option: These are factors that affect permeability, except: a) Soil void ratio b)…

A: Asked; Choose which factors does not affect permeability ?

Q: ind modulus of elasticity of a brass rod of length 200 mm which is subjected to a tensile stress of…

A:

Q: Write the energy balance for the material in a closed container, neglecting potential and kinetic…

A: Energy conservation law states that the total energy of the system and the surroundings can neither…

Q: A 2 mm diameter glass tube is inserted into an open glass of water (contact angle between the tube…

A: Diameter of glass tube =  2 mmContact angle,  = 0

Q: A B Rate of deformation, duldy Shear stress, 7

A: There are several properties defined for fluid such as density, specific gravity, viscosity, etc. In…

Q: In general, why should the operating pressure be high and the operating temperature be low for an…

A: The reason for the high pressure and low temperature for the absorption process is to be mentioned…

Q: Is pinch point always located at the feed stage?

A: The location of the pinch point is to be mentioned.

Q: How we can calculate friction losses due to changes in velocity and direction in side a conduit

A: Friction losses due to changes in velocity and direction in side a conduit can be calculated as

Q: Explain steady flow in relation to fluid mechanics.

A:

Q: For ozone at 25 °C, AG; = 163.2 kJ/mol. a) At 25 °C, compute the equilibrium constant K, for the…

A: Given that  For ozone at 25°C, T = 25 C = 25 +273.15 = 298.15 k   ΔGf' = 163.2 kJ/mole. 3O2(g) = 2O3…

Q: A box is sitting on an inclined plane. One end of the inclined plane is slowly raised, increasing…

A:

Q: Fraction of water

A: To Answer whether the fraction of water in the underflow stream of thickener is zero

Q: Why do positive displacement pumps cause pose more overpressure hazard compared with centrifugal…

A: In a positive displacement (PD) pump, a fixed volume of liquid is trapped inside an enclosed chamber…

Q: Cone has top and bottom diameters of 10 and 20 cm and a height of 10 cm. Calculate the shape factor…

A:

Q: What is the difference between the loading point and the flooding point in a packed column?

A: Loading Point and flooding points refer to the operating conditions of packed column.

Q: Sketch the principle of a hydraulic press.

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: What is a  vane-axial cyclone seperator?

A: This question is from cyclone separators which form an important part in separation processes. The…

Q: The purpose of maintaining vacuum in evaporator is to O a. Reduce in concentration O b. Reduce in…

A: Evaporation is a heat transfer process and evaporators are used to concentrate different types of…

Q: 3. Define the hydraulic and energy grade lines, and explain the method of calculating and drawing…

A: It is asked to define the Hydraulic grade line and energy grade line  and explain the method of…

Q: Rate of movement of fluid passing one another. * O surface tension Shear O Rate of shear O Viscosity

A:

Q: What is a flexible wedge gate used for

A:

Q: Why does the fluid drop in the fluid level measurement experiment when the pump is turned off?

A: In a typical fluid level measurement experiment, the pump is used to recirculate the fluid in a…

Q: Q.3 a). A tensile stress is to be applied along the long axis of a cylindrical brass rod that has a…

A: The magnitude of load is to be calculated.

Q: Explain path line in relation to fluid mechanics.

A:

Q: 8. What type(s) of corrosion occur when metal is subjected to a high- velocity fluid flow with…

A: A) this option is not correct because it is the most general type of corrosion and is caused…

Q: pipe, g/cm', and the melt has a dynamic viscosity of 3.12 g

A: 1. diameter= 10cm = 10*10-2m 2. Density = 7.8 g/cm3= 7800 kg/m3 3. dynamic viscosity= 3.12g/ms=…

Q: Liquid Properties a. Define (note: your definition must be based on the closed conduits/pipe flow):…

A: The definitions of all the terms are written below:

Q: 2. List the most important pipe friction formula.

A: Introduction: The friction loss in uniform, instantly sections of pipe, called "major loss", is…

Q: What is viscosity

A: A fluid is defined as a liquid or gas that flows or deforms continuously when an external force or…

Q: A single crystal is oriented such that the normal to the slip plane and the slip direction are at…

A: Angle between normal to slip  = 60 0 Angle of slip direction = 350 Critical resolved shear stress =…

Q: Which of the following does not affect the rate of liquid flow on porous media A) Type of fluid B)…

A: according to Darcy's law where Q is flow rate K is Permeability is viscosity which is dependent on…

Q: Open loop transfer function for a process is given as 1 , where time constant is in (5s +1)*…

A:

Q: Using a flow chart, show how a lubricant oil with high viscosity index can be manufactured from…

A: In petroleum industries, Crude oil is a type of fossil fuel that is a naturally occurring petroleum…

Q: Which of the following material has the least strain? O a. Elastic band O b. Copper wire O c. Steel…

A:

Q: 1. Determine the maximum allowable vacuum that can be applied to a low-carbon-steel cylindrical…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Explain the friction between the mater (soled with soled, liquid with liquid)?

A: Motion: Motion is the phenomenon in which an object changes its position over time. Motion is…

Q: 5. Absolute pressure is measured relative to atmosphere. Tor F

A: Absolute pressure is measured relative to a full vacuum Whereas the pressure that is measured…

Q: How is pump impeller size calculated

A: The two industrially used pumps are: Positive displacement (PD) pump and Centrifugal pumps. In a…

Q: In a gyratory crusher the size reduction is effected primarily by: 1.impact 2.attrition 3.cutting…

A: This question is based on crushing and grinding operations. We will analyse each option and find the…

Q: What

A: The hydrosphere is combined mass of water on ,above and below surface of earth.

Q: Baffles increases the fluid velocity on the tube side. True False

A: Baffles are used to direct fluid across the tube bundle and run perpendicularly to the shell.…