Which of the following is false for the control system whose block diagram is given? I. Speed error coefficient for zero disturbance input and unit ramp reference input is given with -3Ka. II. The acceleration error coefficient is given by Ka=0. III. The steady state output value for the zero reference input and the unit disturbance input is given with y(x)=0.

Which of the following is false for the control system whose block diagram is given? I. Speed error coefficient for zero disturbance input and unit ramp reference input is given with -3Ka. II. The acceleration error coefficient is given by Ka=0. III. The steady state output value for the zero reference input and the unit disturbance input is given with y(x)=0.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

need handwritten solution only . otherwise downvote.
11 What is the dq component - Park transform The effective stator field current is I, = and the rotor field magnet is oriented at angle 0, = 30" . What is 8. the direct and quadrature components = for the I,. Sketch 1, & 1, in the diagram below to illustrate the relationship between 1,, 0, & L. 0, = 30"
From the phasor diagram in the figure, deduce a expression for the output power, as a function of the armature current, Ia, and angle γ . Draw the curve Power (P) versus current angle (γ), for different levels of excitement Ef. For this consider negligible mechanical losses.
QUESTION 1: For the field current controlled DC Motor, angular velocity control block diagram is given in the figure. Obtain the sensitivity of the steady state error to the variations of the parameters Kp, KD and K. For the variation of which parameter the steady state error is more sensitive? Make a comment. L=0.5[H], J=2[kgm²], R=2[Ohm], B=5[Nms/rad], K=1[Nm/A], Kp=7, Kp=1, K=1. The reference input is assumed to be a unit step input. Wref Kp + Kp. s K7 Ls +R Js + B + K
I have been given the task as a tranee control engineer to design a closed-loop controller an air conditioning unit so that it has the following properties: Maximum overshoot: 10% , maximum time to reach 99% of steady state: 10 seconds, Maximum steady-state error: 10% i have to design a PD controller in a closed-loop system - The steady state error is 1/(1+KP) so i need KP to be at least 9 to meet the brief. I need to choose the K’D parameter so that the zero that it produces is placed somewhere between the open-loop pole, therefore put it at s = -1. I've to assume the closed loop transfer function for this system fits the standard form of a second order response when performing calculations of natural frequency, damping ratio and gain and for plotting the unit step response. I have added the example diagram of a closed-loop system with PD control i was supplied
Explain properly A system with PD controller has a steady-state error and has a long rise time than required. Provide suggestions to eliminate steady-state error while not generating overshoots. Also, the rise time should be decreased
Q4) select the right choice for the following sentences: 1. The critical resistance of the d.c. generator is the resistance of (a) armature (b) field (c) load (d) brushes 2. The external characteristic of a shunt generator can be obtained directly from its......characteristic. (a) internal (b) open-circuit (c) load-saturation (d) performance 3. Which of the following d.c. generator cannot build up on open-circuit? (a) shunt (b) series (c) short shunt (d) long shunt 4. If a self-excited d.c. generator after being installed, fails to build up on its first trial run, the first thing to do is to (a) increase the field resistance (b) check armature insulation (c) reverse field connections (d) increase the speed of prime mover. 5. When load is removed, .......... motor will run at the highest speed. (a) shunt (b) cumulative-compound (c) differential compound (d) series
Q5) The terminal voltage (V), generated voltage (Ẽ), current (Ï), and synchronous reactance (jX) equation of the synchronous motor is as V = Ê + jÏX when the armature resistance (R) is neglected. Also, the angle between the terminal voltage (V) and the generated voltage (Ế) of a synchronous motor is called power angle (8). a) Illustrate phasor diagram of the above synchronous motor for lagging power factor and label all the vectors based on the parameters in the equation. b) Determine at what condition(s) the power angle of the above synchronous motor would be positive? c) If the above synchronous motor is operating at lagging power factor, state how to change its power factor to leading power factor.
Solve it quickly please
Q8. Which of the following quantities should be kept constant when experimentally determining the relationship between load power and the terminal voltage of a self- excited DC shunt generator? (a) Prime mover speed (b) Load resistance (c) Field circuit resistance (d) Prime mover speed and load resistance (e) Prime mover speed and field circuit resistance Q9. Which of the following quantities should be kept constant when experimentally determining the speed regulation characteristics of a self-excited DC shunt motor? (a) Terminal voltage (b) Prime mover torque (c) Field circuit resistance (d) Prime mover torque and field circuit resistance (e) Terminal voltage and field circuit resistance Q10. During an experiment to determine the excitation curve for a separately-excited DC shunt generator at rated speed a student obtained the following measurements: Field current = 148 mA. No-load terminal voltage = 77.2V Prime mover (rotor) speed = 1828 rpm. Which of the following is the correct…
i.A closed-loop control system is created using a proportional controller. Show that such a system has a steady state error of 1/(1+Kp) and therefore the steady state error condition can be achieved with a proportional gain of 9 or more.
A shunt generator on dest is separately encited and driven at 1000 rev /min. The open circuit test chars. are given Field test CA o 0'157 O.477 0 663 O.805 1.0 129 Induced Emf CU) 12a5 300 400 100 450 500 550 ine mlc is then shunt Connected and gun at l000 revlmine with a constant field cicuit esistance of 540R. The agmature docuit resistamee is er. Deduce and plot the load Chargaetesistics of this mle,negleeting effeetof amarterre reaction.what is value of manimum lbud cursrent.