2AVa docs.google.comWhich of the channels are classified by functions*O Power canalO Lined canalO Branch canalA clay sample volume and weight are 35 cm3 and 0.50 N, respectively. If assumespecific gravity as 2.65, compute the porosity. *O 45O 553540Water has been applied for 2 hours at rate 70 Lis, Loss of irrigation water asrunoff at 30 Ls for 1 hour. Determine water application efficiency *O 78%100%127%22%Determine the diameter of corrugated field drain required to drain area of (200*100) m if the drainage rate Q = 3mm/day and slope of field drain = 12 cm/km. *110 mm90 mm150 mm82 mmWhat is thA most iO O

Solution Note- According to Bartleby Guideline, you asked multiple questions I solved only first for…

Answered: Which of the channels are classified by…

Which of the channels are classified by functions Power canal Lined canal Branch canal A clay sample volume and weight are 35 cm3 and 0.50 N, respectively. If assume

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter5: Soil Improvement And Ground Modification

Section: Chapter Questions

Problem 5.13P

See similar textbooks

Related questions

Q: Which the following is a functional relation connecting the value of specific gravity, among voids…

A: Given data : Specific gravity=GVoid ratio=eDegree of saturation =SWater content=w

Q: A soil has a discharge velocity of 6 x 10 m/s and a void ratio of 0.5. What is its seepage velocity?

A: Given data : Void ratio (e)=0.5Velocity (V)=6×10-7 m/s

Q: Question attached

A: Calculate the over consolidation ratio by using the equation. OCR=0.58N60Paσo' …… (1) Here, OCR is…

Q: (b) The results of a constant head permeability test for a fine sand having a diameter of 90 mm and…

A: Using formula

Q: A SOIL SAMPLE WAS COMPACTED REDUCING ITS VOID RATIO BY 35%. IF THE WEIGHT AND VOLUME IS 7kN AND…

A: It is required to determine the bulk unit weight of soil. γ=WV=7 kN0.3 m3=23.33 kNm3

Q: The coefficient of permeability of a sand at a void ratio of 0.62 is 0.03 cm/sec. estimate the…

Q: Shear Strength of Soil The following are the results of two consolidated-drained triaxial tests on a…

A: Please refer the attached image for complete solution. THANK YOU.

Q: 8. For a normally consolidated clay specimen, the results of a drained triaxial test are as follows:…

A: Given data: The total axial stress at failure will be major principal stress at failure and is…

Q: If a soil sample of volume =1 cm3 and actual density =2000 kg/m3, and bulk density = 1700 kg/m3, the…

Q: The results of a constant head permeability test for a fine sand are as follows: Diameter of the…

A: solution For constant head permeability dia of sample d=33cm Area=π4d2=π4×332=855.3cm2Length of the…

Q: If a soil sample of volume =1 cm³ and actual density =2000 kg/m³, and bulk density = 1700 kg/m3, the…

A: If a soil sample of lume = 1 cm³ and actual density = 2000 kg/m³, and bulk density = 1700 kg/m3, the…

Q: The critical hydraulic gradient for a soil sample is equal to 1.01. If the specific gravity of the…

Q: he dry unit of a sand with a porosity of 0.387 is 1600 kg/cu.m. Determine the following: a) Void…

A: Given- Porosity n=0.387Dryunit weight γd=1600Kg/Cu.m Unit weight of water γw=1000Kg/m3=10Kn/m3…

Q: If a soil sample of volume =1 cm3 and actual density =2000 kg/m3, and bulk density = 1700 kg/m3, the…

Q: 2.9 A normally consolidated clay has the following values. Void ratio, e k (cm/sec) 0.2 x 10 0.91 X…

A: void ratio and permeability of a soil medium can be related to each other as follows…

Q: Q1: A saturated Sample of clay with an SL of 25% has a natural water content of 35%. What would its…

Q: An undisturbed sample of clay has a wet mass of 30 kg, a dry mas of 25 kg, and a total volume of…

A: Given: Wet mass of clay = 30 kg Dry mass of clay = 25 kg Total volume = 0.014 m3 Specific gravity =…

Q: A soil sample has a bulk unit weight of 9.62kN/m^3 and a dry unit weight of 17.66 kN/m^ 3 .Given…

Q: Two specimens of clay A and B are tested in a consolidated apparatus. If: (m)A=3.6 x 10-4 m²/kN…

Q: Shear Strength of Soil The following are the results of two consolidated-drained triaxial tests on a…

Q: The void ratio and specific gravity of a sample of clay are o.73 and 2.7 respectively. If the voids…

Q: 4. For a normally consolidated clay, the following values are given. k (cm/sec) 0.45 x 106 e 0.78…

Q: A cube soil sPecimen of dimensions loem X locm xlocm has Mass ofl.9o kg and water conten t We = )5 %…

Q: Shear Strength of Soil The following are the results of two consolidated-drained triaxial tests on a…

A: To Determine Shear strength parameters of the soil.

Q: 16. For a constant laboratory permeability test on a fine sand, the following data are given:…

A: Length of specimen, L=16cmDiameter of specimen, D=97mm=9.7cmConstant head difference, h=51cmVolume…

Q: If a soil sample of volume =1 cm3 and actual density =2000 kg/m3, and bulk density = 1700 kg/m3, the…

Q: Estimate the coefficient of permeability for a sand formation, given the following representative…

A: For sand calculating the void ratio by using hazen williams formula:

Q: 4. In a consolidated-drained triaxial test on a clay that is normally consolidated, the results are…

Q: 4. For a normally consolidated clay, the following values are given. k (cm/sec) 0.45 x 10 e 0.78 1.1…

A: For e = 0.78, k = 0.45×10-6 and for e = 1.1, k = 0.88×10-6 we have to find k at void ratio e =0.97

Q: HYDRAULIC CONDUCTIVITY PROBLEM 1: The results of a constant head permeability test for a fine sand…

Q: For a constant laboratory permeability test on a fine sand, the following data are given: Length of…

Q: A consolidated-drained triaxial test was conducted on sand. The results are as follows: Confined…

A: Using formula to get internal friction angle

Q: A soil sample has a void ratio of 0.67. Find the ratio between discharge velocity and seepage…

A: Solution; Given that; Void ratio (e)=0.67

Q: 4. For a normally consolidated clay, the following values are given. k (cm/sec) 0.45 x 10 0.78 I.…

Q: A clay sample volume and weight are 35 cm3 and 0.50 N, respectively. If assume specific gravity as…

A: VT = 35cm3Ws = .50NG = 2.65

Q: A soil has a discharge velocity of 6 × 107 m/s and a void ratio of 0.5. What is its seepage…

Q: A soil sample has a compression index of 0.3. If the void ratio e at a stress of 2940 lb/ft2 is 0.5,…

A: Solved

Q: The porosity of a certain soil sample was found to be 80% and its specific gravity was 2.7; the…

Q: A normally consolidated clay has the following values. Void ratio, e k (cm/sec) 1.4 0.2 x 10-6 1.9…

Q: Use 10 kN/m³ for the unit weight of water. Question 10 A site associated with an excavation project…

A: Stress at middle of clay layer is given by ; σ'o = γsat - γwSand×6 + γsat - γwclay×3 σ'o = 20 -10×6…

Q: A saturated sample of undisturbed clay has a volume of 20 cm³ and weighs 33 g. Af weighteduces to 21…

Q: 20.0 kN/m^3 at a water content of 8.0%. Use Gs=

Q: Q2) A dry sample of soil having the following properties, L.L. = 52%, P.L. = 30%, Gs = 2.7, e =…

A: Given LL=52% PL=30% Gs=2.7 e=0.53

Q: The following data are obtained for a soil specimen: Mt=221gm, Ms=128gm, Gs=2.70 and S=75%. Find the…

A: Given: The total mass of the soil (Mt) is 221 gm. The mass of the dry soil (Ms) is 128 gm. The…

Q: A saturated undisturbed sample from a clay strata has moisture content of 22.22% and specific weight…

Q: The soil sample in a tri axial test have the following stresses Cell pressure 25 Кра 34 Кра Pore…

A: For drained condition .Case 1 : σ1=σ3+σ∝=25+20=45 kpaSo ,σ1-u=σ3-utan2θ+2 C…

Q: A soil sample has an average grain diameter as 0.03 mm. The size of interstices is one eight of the…

A: Given data in question Average grain diameter Surface tension To find out Water rise

Q: PROBLEM 50: Compute the compression index of undisturbed clay having a plastic limit of 32% and a…

A: wL=32% wp=8% Compression index,Cc=0.009(wL-10) => Cc=0.009(32-10)=0.198

Concept explainers

Hydroelectric Energy

Hydroelectric energy is also known as hydropower or hydroelectricity. The term hydropower refers to the power obtained from water motion. By the term 'power', primarily means the generation of electricity. A hydropower plant or hydroelectric power plant utilizes the kinetic energy or pressure energy of flowing water into electrical energy. Unlike conventional energy sources used for power generation, electricity obtained from hydraulic power contributes to zero greenhouse gas emissions.

Question

2AV
a docs.google.com
Which of the channels are classified by functions*
O Power canal
O Lined canal
O Branch canal
A clay sample volume and weight are 35 cm3 and 0.50 N, respectively. If assume
specific gravity as 2.65, compute the porosity. *
O 45
O 55
35
40
Water has been applied for 2 hours at rate 70 Lis, Loss of irrigation water as
runoff at 30 Ls for 1 hour. Determine water application efficiency *
O 78%
100%
127%
22%
Determine the diameter of corrugated field drain required to drain area of (200
*100) m if the drainage rate Q = 3mm/day and slope of field drain = 12 cm/km. *
110 mm
90 mm
150 mm
82 mm
What is thA most i
O O

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q- If a soil has a voids ratio of 0.68 and water percolating through it has a discharge velocity of 1.35*10-2cm/s. Calculate its seepage velocity.
Describe spring analogy system with neat sketch. [5] A clay layer, whose total settlement under a given loading is expected to be 11cm settles 3cm at the end of inonth after the application of load increment. How many months will be required to reach a settlement of Scm? How much settlement will occur in 10 months? Assume the layer to have double drainage system. [7] Maximum size for Files You can drag and drop files here to add them. Accepted file types All file types
A soil sample with Gs=02.75,e=0.8 and w(moistore con dent)= 0.0 8 and has a Volom e of 0.5m3 then fird Va, VT, Vv = ? WsiWwiWT, Vw = ? %3D moisd unid weight=? ? Degiee of Saduradd=? of water wouldyou need do add to thad Soil Sanple to Achieve Sclo0'/. How mucd vol
Earth is required to be excavated from the borrow pits for buildingembankment as shown in the figure. The moisture unit weight ofthe borrow pits is 18 kN/m3 and its water content is 8%. Estimatethe quantity of earth required to be excavated per meter length ofembankment. The dry unit weight required for the embankment is15 kN/m3 with a moisture content of 10%. Assume the specificgravity of the solids as 2.67. Also determine the degree ofsaturation of the embankment and volume of the water in theembankment
Juo Situation 1: alqma Isoubilya s no 300 hom63 28W 120 illdsom bsod terco A Sito be A layer of saturated clay 4 m thick is overlain by sand 5 m deep, the water table being 3 m below the surface. The saturated unit weights of the clay and sand are 19 and 20 kN/m², respectively. Above the water table, the dry unit weight of the sand is 17 kN/m³. Determine the following: 169 11 1. Effective stress. 167 kPa b. 71.38 kPa 2. Water pressure. a. 167 kPa b. 71.38 kPa ASYMENT nim ni PTSS.O d. nimal+vsso d almal 2017.O .b 3. Total stress or pressure. 167 kPa 108.14 kPa 58.86 kPa im ni ni vioolov.sgisdbal 108.14 kPa 58.86 kPa nimal XP240 biov odt li visolev ogeqso? TA24.0 niral 201.I d C. 108.14 kPa dribsnodeb. sin 71.38 kPani benimsieb 26 dalam 58.86 kPa vivibubno osbyd SAT bozu sish edT 191emseneg baad gailiste to seu geblso
2nds X CUC UEF. High High High High High High High ar Users/HC/AppData/Local/Temp/2nd Sessional Soil.pdf .*. O a Search 立业回 + Automatic Zoom the compacter is being used? Q. No. 03 (10 Marks) The soil profile shown below is typical of Miami-Dade County. Estimate the equivalent permeabilities Kvleq) and Kh(eq) in cm/sec, and the ratio of Khfeg)/Kv(eq)? I m Fine Sand k= Ix10" cm/sec Pamlico Formation 5 m Porous Limestone k-2x10 cm/sec Miami Formation 3 m Fine Sand -1x10 cm/sec Fon Thompson Formation 12 m Upper sandy Limestone k- 2x10 cm/sec Fort Thompson Formation Evate Wi Settince TOSHIBA BACK GPACE T Y PI ENTER C. G Y K 4. 0 O SHIFT S ALT CTRL GR
Qus - If the void ratio and discharge velocity for soil is 0.5 and 6 * 10^-7 * m / s respectively, what is the value of seepage velocity (m/s)?
Question 5 Water is flowing in a canal of width 5m at a rate of 20 cumec. Average diameter of the particles of the medium through which water is flowing is 0.53mm. What is the Lacy scour depth of the canal?
3. Three boreholes (BH) along a proposed road intersection are shown in Figure la and b. The soils in each borehole were classified using ASTM-CS. Sketch a soil profile along the center line. BH ВН 2 BH 3 100 m 100 m (a) Plan El: 100.2 El: 99.5 E1: 102.7 SP ML CH 10 SP-SM 15 - GP-GM ВН 2 ВН З 20 ВН 1 (b) Borehole soil Figure 1 Depth (m)
The section through a long cofferdam is shown below, the coefficient of permeability of the soil being 6x10-8 m/s. Determine the quantity of seepage entering the cofferdam. 5.50 m I 0 1 2 3 4 5 As = 0.70 ml +cl 10 B ax 15 m
Question 2 Figure Q2 shows a flownet for a concrete dam with a sheet pile cut-off at the upstream face. The soil beneath the dam has a permeability of 2×10-7 m/sec. 6m AVA 18m Dam Impervious Figure Q2 9m 7m 2m 12m AVAVAVAVAWAY (a) Explain what these solid and dashed lines in Figure Q2 represent and their physical significance in engineering application. (b) Using the flownet above, estimate the flow rate beneath the dam and the uplift water pressure at Points A and B on the bottom of the concrete dam. (c) Using the flownet above, estimate the vertical effective stress at Point C. The saturated unit weights of soil and unit weight of water are taken as 20 kN/m³ and 10 kN/m³, respectively.
here are the answer, only need solutions 1.f = 11.46 MPa 2.Mcr= 88.90 kN-m 3.fconc= 17.14 MPa; fsteel= 318.20 MPa