When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.17 in. In segment (2), the normal strain is measured as 1,450 uin./in. Assume L₁ - 45 in. and L₂ - 94 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. P A Answers: (a) in.6₂ = (b) £₁ = L₁ i i B (2) L2 in. uin./in.

When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.17 in. In segment (2), the normal strain is measured as 1,450 uin./in. Assume L₁ - 45 in. and L₂ - 94 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. P A Answers: (a) in.6₂ = (b) £₁ = L₁ i i B (2) L2 in. uin./in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe is subjected to a tension force of P = 70 kN. The pipe outside diameter is 32 mm, the wall thickness is 6.0 mm, and the elastic modulus is E = 180 GPa. Determine the normal strain in the pipe. P Select one: O a. 0.001263 mm/mm O b. 0.000535 mm/mm O c. 0.000568 mm/mm O d. 0.000794 mm/mm e. 0.001382 mm/mm O f. None
QUESTION 2 The rigid bar ACE is supported by two steel rods AB and CD (Esteel = 200 GPa) with the cross sectional areas of each rod is given as shown in Figure Q2. (a) Determine the position d of the 30 kN load so that the average normal stress in each rod is the same. (b) Find the strain in rod CD, ɛcD (c) Determine the horizontal displacement of point E 1.2 m ACD = 600 mm? 0.8 m E 30 kN AAB = 900 mm2 d B 1.8 m Figure Q2
The rigid bar ABC pivots about support B. After application of load P, end C of the rigid bar moves upward by 0.07 in. If the length of bar (1) is L₁-41 in, determine the average normal strain in bar (1). Assume that a-135 in, b-39 in, and c-0.15 in a b C Rigid bar 4 Part 1 * Incorrect Determine the distance that end A of the rigid bar moves downward, if end C moves upward by 0.07 in Answer: in VA i 00361
The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (-0.55 in., -0.17 in.). Assume a = 10 ft, b = 20 ft, c = 7 ft, and d = 14 ft. Determine the normal strain in each bar. Answer: EAB || A EBC= i P a (1) y B με με b (2) C d
5 decimal places Determine the total strain (mm/mm) of a 2.64-m bar with a diameter of 21 mm subjected to a tensile force of 71 kN at a temperature increase of 49 C°. Consider the α=27.3 µm/mC° and E = 122 GPa.
When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.15 in. In segment (2), the normal strain is measured as 1,450 uin./in. Assume L₁ = 44 in. and L₂ = 82 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. (1) P L₁ B (2) L2
When an axial load is applied to the ends of the bar shown, where L₁ = 30 in. and L₂ = 80 in., the total elongation of the bar between joints A and C is 0.100 in. In segment (1), the normal strain is measured as 1700 µin./in. Determine the normal strain in segment (2) of the bar. A (1) L₁ 662 μin./in. O 784 μin./in. O 373 μin./in. O 719 μin./in. O 613 μin./in. B (2) L2
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y = 2.1 lb/in.³ is the specific weight of the material, y = 2.0 in. is the distance from the free (i.e., bottom) end of the bar, L = 5 in. is the length of the bar, and E = 27000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar (c) the maximum normal strain in the bar. Answer: (a) 8 = i (b) avg (c) Emax = i x10 in. με με