The hoisting beam assembly shown is supported by two 20- mm-diameter bolts at A and a 150 mm x 200 mm plate at B. In this problem, a = 1.2 m and b = 2.8 m. If the allowable tensile stress of the bolts at A is 112 MPa, which of the following gives the maximum safe value of W in kN? A. 45 C. 30 B. 60 orld to D. 15 BES H a 8804 + A Plate B 11 11 11 awodas m b lo msh lisme A W musia

The hoisting beam assembly shown is supported by two 20- mm-diameter bolts at A and a 150 mm x 200 mm plate at B. In this problem, a = 1.2 m and b = 2.8 m. If the allowable tensile stress of the bolts at A is 112 MPa, which of the following gives the maximum safe value of W in kN? A. 45 C. 30 B. 60 orld to D. 15 BES H a 8804 + A Plate B 11 11 11 awodas m b lo msh lisme A W musia

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 16 mm thick tension member is connected by two 6.25 mm spliced plates as shown. The tension member carries a service loads of dead load of 110 kN and a live load of 100 kN. 40, 80 , 40 , 40, 80 40 1625 mm 16 mm 1625 mm Fy 248 MPa Fu = 400 MPa Diam. of bolts = 16 mm Fnv = 300 MPa O Determine the nominal strength for one bolt due to shear. O Determine the nominal strength for one bolt due to bearing strength of the connection. ® Determine the number of bolts required for the connection.
The angle bracket shown, 75 mm x 75 mm x 15 mm thick, is 200 mm long. It is connected to the 16 mm thick flange of the column support with 2 of 16 mm diameter bolts. The bracket is subjected to a load of 42 kN from beam A. Assume that the load is applied concentrically at the connection. 1. Determine the resulting bolt shear stress in MPa 2. Determine the resulting bolt shear stress in MPa 3. Determine the critical bolt shearing stress in MPa
H.W The omPound shaft Shown isattached to Kigid SuPprts, for the bronze Segment AB, the diameter is 75mm G=35 GN/m and TS60MNIM. for steel Segment Bc, the dlameter is Somm, G= 836N/mand TS8OMNIMIF a=2m and b= 1.5m,lam Pute the maximum torguelT) that Gan be applier?
g) what is the flexural/local buckling capacity of the shear plate of the shear connection in kips? (2 decimal places)A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
From the bolted connection shown, the diameter of bolts is 20 mm with the hole diameter equal to 3mm larger than the bolt diameter, the angular section is 100x75x8mm, with an area of 1340 mm^2. Thickness of gusset plate is 9 mm. the gusset plate. (a)If T = 200KN, compute the shearing stress on the bolts. (b)If the allowable shearing stress on the bolt is 145MPa, compute the value of T.
A rigid bar AC is supported pinned supported at A and bar DB at B. See typical bolt connection detail. A concentrated weight, denoted as W is attached at the end of the rigid bar. L1 = 2.6 m L2 = 2.1 m H= 1.2 m W= 14 KN What is the required diameter of the bolt (in mm) at connection B given the allowable shearing stress to be 40 MPa ? Consider single shear. L1 L2 A B C H D इस W CONNECTION AT B
2- A 2m COPPER BAR SUBJECTEO TO A TENSILE IS SUSPENDED FROM A LOAD IBO KN SUPPORTED BY TWO IDENTICAL PIN THAT S pOSIS AS SHON OF THE LOWER AFPLIED TENSILE POSTS SUPPORT THE STEEL DETERMINE THE TOTAL DEFORMATION END OF THE LOAD HINT: NOTE THAT THE STEEL PIN WHERE THE COFPER BAR IS ATTACHED. COPPER BAR DUE TO STEEL POST L=0.5m A= 4500mm E- 200GPA COPFER BAR L- am A= 4800 Mn E- l20 GPa 180KN
Instructions:-Write down each step clearly in calculation suggestion what you are doing.( you need to tell why you selected particular value ofø (phi) and U). What and why you are calculating certain step Consider R= 433.5 PROBLEM A welded tension member is consisting of two channels placed 400mm back to back with flanges turned out. Select a channel for factored tensile of 4RKN using A36 steel and AISC specifications.The member is to be 15m long. PLASE USE THE EXAMPLE AS GUIDE OF ALL STEPS AND FORMULAS TO BE USE
7. The yoke-and-rod connection shown below is subjected to a tensile force of 5kN. Determine the minimum thickness of yoke if the bolt has a diameter of 25mm and the bearing stress is limited to 12MPA. 40 mm 5 kN. 30 mm 25 mm 5 kN
أ.د. رمضان المبروك A PL170mm x 10mm tension member is welded to a gusset plate as shown in Figure below. The steel is A36. Assume that Ae = Ag and compute the following. %3D fy = 250 MPa & f, = 400 MPa %3D %3D PL 170mmx10mm a. The design strength for LRFD. . The allowable strength for ASD. roblem (4):
The following image shows a front and side view of the column connection. The bolts have a diameter of ¾”. The W12X65 profile has a thickness of 0.605”. Determine: a. The shear stress in the bolts. Answ. 11.81 ksi b. The axial stress in the bolts. Answ. 23.62 ksi c. The support stress in the W12X65 profile. 11.50 ksi
5. what is the shear rupture capacity of the shear plate of the shear connection in kips? (2 decimal places)A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi