What type of CAD software could be used to test the medical scaffold made out of TPU that will be printed using stereolithography (SLA). The medical scaffold will be surgically implanted around the pancreas to enable the infusion of Islet beta cells which are encapsulated within the scaffold to provide diabetic patients with a functional pancreas. E.g. hydrostatic pressure testing/torsion tests What other type of physical testings should be taken?  E.g. Brunauer–Emmett–Teller (BET) test to check the porosity of the material

Need help

On a rotor wing NVG flight, your aircrew is circling (clockwise) a target area illuminated by an aerial parachute flare. The door gunner on the side of the aircraft opposite the flare (left) notices the ground getting closer and calls, "knock it off". What visual illusion just occurred and which aircrew member(s) were affected? OA. Moth effect; pilot, copilot, right door gunner OB. False horizon; left door gunner OC. Lean-on-the-sun illusion; all crew members O D. G-excess; left door gunner

3. Microfluidic channels will need to be fabricated on a key micro-scale sensor used by aerospace industries. Before running machining tests and analyzing machined quality, preliminary efforts are needed to evaluate selected materials and factors affecting machining process¹. Three material candidates have been selected, including 422SS (stainless steel), IN718 (nickel alloy), and Ti64 (titanium alloy) with their measured tensile properties and equation of true stress-true strain relationship used listed below. Tref25°C. Specifically, three factors will need to be evaluated, including different materials, temperature, and size effect. Please calculate true stress values for true strain ranging between 0-3 for each case listed below. Material A (MPa) & (S-¹) Tm (°C) 870 0.01 1520 422SS (Peyre et al., 2007) IN718 (Kobayashi et al., 2008) Ti64 (Umbrello, 2008) 980 1 1300 782.7 1E-5 1660 Material 422SS (CINDAS, 2011) IN718 (Davis, 1997) Ti64 (Fukuhara and Sanpei, 1993) 0 = X G (GPa) 1+ B…

https://drive.google.com/file/d/1X0Sk9U2pT7lwJ9IB--kLkGngHm46SywH/view?usp=sharing

subject(control engneering) pls show full steps sir take your time sir

MECT361 Mechatronics Components and Instrumentation PLEASE GIVE ME THE short answer and wite it by keyword thanks

Pressurized eyes Our eyes need a certain amount of internal pressure in order to work properly, with the normal range being between 10 and 20 mm of mercury. The pressure is determined by a balance between the fluid entering and leaving the eye. If the pressure is above the normal level, damage may occur to the optic nerve where it leaves the eye, leading to a loss of the visual field termed glaucoma. Measurement of the pressure within the eye can be done by several different noninvasive types of instruments, all of which measure the slight deformation of the eyeball when a force is put on it. Some methods use a physical probe that makes contact with the front of the eye, applies a known force, and measures the deformation. One non-contact method uses a calibrated “puff” of air that is blown against the eye. The stagnation pressure resulting from the air blowing against the eyeball causes a slight deformation, the magnitude of which is correlated with the pressure within the eyeball.…

This exercise requires showing the complete scanned strokes and procedures, adding it to a pdf document with evidence of all the exercises and the honesty letter. A Titanium specimen with a diameter of 0.8 [in] and 2.5 [in] in length is stretched in uniaxial tension. 1. What is the maximum elongation (DI) of the material. If the deformation is completely elastic? 2. What force is being applied Consider the material properties S_UTS=1205 [MPa]; Sy= 1075 [MPa]; E= 100 [GPa] in the following space write the values found as follows, do not forget the units (-0.5 pts if 4d units do not appear): ]; F= [];

Please answer within one hr i will give good rating.