A hotel chain based in the United States contracts with a European vacuum cleaner manufacturer to supply a large number of uprightcleaner units. After delivery, the hotel raises questions about manufacturer vacuum cleaner performance claims, pointing out that theunits should have been tested to meet ASTM 558, an American standard. The manufacturer notes the advertised performance is basedon IEC 60312, a European standard, and the two test codes will yield similar, if not exact, results. Investigate both test codes andaddress similarities and differences. Is there a legitimate claim here?

Given-Information:- The United States does a contract with a European vacuum cleaner company. ASTM…

Answered: eaner units. After delivery, the hote…

Engineering

Mechanical Engineering

eaner units. After delivery, the hote mits should have been tested to mee m IEC 60312, a European standard, lics.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(b) 2000 light bulbs were tested by the manufacturer. After 500 hours of testing, it was found that 5 out of all the light bulbs subjected to testing have failed. Strict quality control has been implemented to eliminate premature failures. Assume the light bulb has a constant failure rate. What is the failure rate, Mean Time Before Failure (MTBF) and the reliability of the light bulb after 500 hours? l vang
A multinational business unit has an examination system for the batches of ventilator units bought from dealers. A batch typically comprises 40 ventilators. In the inspection system, a random sample of 20 is selected and all are tested. Suppose there are 5 faulty ventilators in the batch of 40. What is the probability that for a given sample there will be 2 faulty ventilator?
Testing and Rework Bolts installed on a production line are tightened with automatic wrenches. They are to be tightened sufficiently to yield the full cross-section in order to produce the highest possible initial tension. The limiting condition is twisting off the bolt head during assembly. The bolts have a mean twisting off torque of 20 Nm with a standard deviation of 1 Nm. The automatic wrenches have a standard deviation of 1.5Nm. What mean value of torque wrench setting would result in only 1 in 500 twisting off during assembly? Give a rough estimate only. A unit has a constant failure rate of 0.3% per 1000 hours. What is its MTBF? What are the probabilities of the unit successfully completing missions of 10000, 100000 and 1000000 hours? Give a rough estimate only. Please provide an in depth answer for the above questions, thank you so much!
Bottles for room spray are supposed to weigh exactly 16 oz. Inspectors want to develop process control charts. They take o7 boxes of five bottles each and weigh them. They obtain the following data. The mean weights of each of the 07 samples are 14.6,16.5,18.1,13.2,16,15.9, and 14.8 respectively. Likewise, the range values for the each of 07 samples are o.7,0.5, 0.4,0.2,0.4,0.5, and o.9 respectively. Ebr the X-bar charts and R-charts, the Parameters, A2, D3 and D4 are respectively.
Manufacturer's specifications state that the piston in a motorcycle engine must have a diameter of d = 74.940 ± 0.002 mm to be serviceable. Your assistant uses a (presumably accurate) high-precision micrometer which has a precision of ±0.001 mm to measure all of the pistons that he can find. From the following list that he gives you, select all of the measurements that are most certainly within specifications. d = 74.933 mm d = 74.94 mm d=74.9418 mm d=74.940 mm d = 74.944 mm d = 74.938 mm d = 74.939 mm d = 74.941 mm d = 74.9420 mm d = 74.9389 mm
CHAPTER 5 : DIESEL ENGINE POWER PLANT A six cylinder, four-stroke CI engine is tested against a water brake dynamometer for which B.P = WN/17x10' in kW, where W is the brake load in newton and N is the speed of the engine in the r.p.m. The air consumption was measured by means of a sharp edged orifice. During the test following observersations were taken : • Bore • Stroke • Speed • Brake load Barometer reading = 10 cm = 14 cm = 2500 rpm = 480 N = 76 cm Hg • Orifice diameter • Co-efficient of discharge of orifice • Pressure drop across orifice • Room temperature Fuel Consumption = 3.3 cm = 0.62 = 14 cm of Hg = 25°C = 0.32 kg/min Calculate following : i. The volumetric efficiency The brake mean effective pressure ( b.m.e.p) The engine torque The brake specific fuel consumption ( b.s.f.c ) ii. iv.
MECT361 Mechatronics Components and Instrumentation 8.1. Why is it not possible to connect sensors such as thermocouples, strain gages, and accelerometers directly to a digital computer or microprocessor? PLEASE GIVE ME THE REFRENCE I Will get zero if you didn't put the refrence
One step in the manufacture of a certain metal clamp involves the drilling of four holes. In a sample of 100 clamps, the average time needed to complete this step was 80seconds and the standard deviation was 15 seconds. a.Find a 95% confidence interval for the mean time needed to complete the step. b.Find a 99.5% confidence interval for the mean time needed to complete the step. c.What is the confidence level of the interval (78,82)? d.How many clamps must be sampled so that a 95% confidence interval specifiesthe mean to within ±1 seconds? e. How many clamps must be sampled so that a 99.5% confidence interval specifies the mean to within ±1 seconds?
A work measurement analyst at the Dorben Company took 10 observations of a high-production job. He rated the performance of each cycle and then calculated the average normal time for each item. The item with the largest dispersion had a mean of 0.30 minutes and a standard deviation of 0.03 minutes. If it is desired to have sample data within ±5% of the actual data, how many observations should the time study analyst take of this operation?
The data provided by a water bottling company for the year 2020 to carry out Break Even Analysis and provide them the results, is as follows. The fixed cost of the year is 9000.0 R.O The estimated sales are 2200000 units The cost of water treatment / unit 12 baize The cost of bottling / unit 08 baize The cost of labelling / unit 08 baize The cost packing / unit 10 baize The cost of labour and maintenance / unit 20 baize The cost of 1 liter bottle (plastic bottle) 12 baize Each unit is sold at price 95 baize Construct the B.E.P chart on a graph sheet and indicate M.o.S, B.E.P and also indicate the new B.E.P, & M.o.S after the improvement measures has been taken and show all mathematical calculations. 1. Determine the B.E.P 2. Determine the profit 3. Margin of safety. 4. Write your decisions to improve the profits of the company and to reduce the B.E.P
Design a complete and safe experiment to find out how increasing the distance of air that alpha particles must pass through affects their detection by a Geiger Muller tube. G-M In your plan you must include: A hypothesis that can be tested Am-041 . An identification of the independent, dependent, and two control variables A list of any additional equipment needed A justification of why additional equipment is needed A description of your method, How you will collect sufficient data A relevant safety consideration
The data shown in Table 1 are the deviations from nominal diameter for holes drilled in a carbon-fiber composite material used in aerospace manufacturing. The values reported are deviations from nominal in ten-thousandths of an inch. (a) Set up and R charts on the process. Is the process in statistical control? (b) Estimate the process standard deviation using the range method. (c) If specifications are at nominal ±100, what can you say about the capability of this process? Calculate the PCR Cp Table 1. Hole Diameter Data Sample Number X1 X2 1 2 3 4 5 6 7 8 9 10 11 12 14 15 16 17 18 19 20 -30 +50 0 -50 -10 -10 +20 -40 0 0 -30 0 +20 0 0 +70 0 +10 +40 +30 +30 +30 +10 0 +20 +50 +50 -20 +50 -60 +10 0 0 +20 +10 -20 -10 0 +20 X3 X4 X5 -30 +20 +30 +50 +40 +20 +30 +20 +30 +20 +30 0 +20 +10 +40 +10 +10 -10 +50 -10 -30 -10 +50 +40 0 +30 -10 0 +30 +30 -20 +50 +30 +10 +40 +20 0 +30 +10 +30 -20 +30 +30 +20 -20 +50 +20 +10 -40 +20 -20 -10 -10 0 -20 +10 +10 +50 0 +10